1. Manuals
  2. Brands
  3. Bay Networks Manuals
  4. Switch
  5. 5399
  6. Quick start manual

Bay Networks 5399 Quick Start Manual

Remote access concentrator
Hide thumbs Also See for 5399:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Manual, Quick Start Manual
Model 5399 Remote
Access Concentrator
Quick Start for Windows
Read before installing and using Remote Annex
Software Release 5.0
These installation notes contain information specific to the
release of the Model 5399 Remote Access Concentrator
module.
Part No. 166-024-865
April 1997
Rev. A

Advertisement

Table of Contents
loading

Related Manuals for Bay Networks 5399

Summary of Contents for Bay Networks 5399

  • Page 1 Access Concentrator Quick Start for Windows Read before installing and using Remote Annex Software Release 5.0 These installation notes contain information specific to the release of the Model 5399 Remote Access Concentrator module. Part No. 166-024-865 Rev. A April 1997...
  • Page 2 Annex, Remote Annex, Annex Manager, Remote Annex 2000, Remote Annex 4000, Remote Annex 6100, Remote Annex 6300, Remote Annex 5390/Async, Remote Annex 5391/CT1, Remote Annex 5393/PRI, 5399 Remote Access Concentrator, BayStack Remote Annex 2000 Server, Quick2Config, Bay Networks, Bay Networks Press, and the Bay Networks logo are trademarks of Bay Networks, Inc.

  • Page 3: Table Of Contents

    Before Installing the Software..............6 Prerequisites .
  • Page 4 Contents 166-024-865 Rev. A...
  • Page 5 5399 Remote Access Concentrator Module (5399 RAC) in a Bay Networks Lattice System 5000 Hub, and configuration of the 5399 RAC using Quick2Config Annex, a Windows-based Annex management tool. The procedures in this guide cover: •...

  • Page 6: Before Installing The Software

    5399 RAC Quick Start for Windows Before Installing the Software Prerequisites To install Remote Annex Server Tools The CD-ROM includes the appropriate Annex software release required by the Remote Annex Server Tools Windows NT Log On Privileges If you install Remote Annex Server Tools for Windows NT on a primary domain controller, all users must have the right to log on locally.

  • Page 7: Software Installation

    To delete users or groups, highlight a name and click on Remove • Operating images that are downloaded to the Annex • NA command line interface for configuring and managing the Annex • Quick2Config Annex for configuring Annex ports 5399 RAC Quick Start for Windows Remove 166-024-865 Rev. A...

  • Page 8: Workstation Software

    5399 RAC Quick Start for Windows To install Remote Annex software on the server: Refer to Installing Remote Annex Network Software for Windows for installation details. Workstation Software The NA command line interface and Quick2Config Annex software can be loaded on Windows NT Workstations (3.51 or 4.0) and on Windows 95 platforms.

  • Page 9: Hardware Setup

    Hardware Setup This section provides abbreviated instructions for installing the hardware. For more detailed information, see Model 5399 Remote Access Concentrator Module Hardware Installation Guide. To set up the 5399 RAC module: Figure 1. Model 5399 Jumper DIP Switch Locations...
  • Page 10 ASCII. Press the Esc key to display the Slot Selection menu. Select the 5399 RAC module and press r to reset the module. Initialize the 5399 RAC as a System 5000 Hub module and enter the Monitor Mode. Follow the instructions in “Remote Access Concentrator”...

  • Page 11: Setting The Network Address

    After initializing the hardware, you initialize the firmware and enter the IP address of the 5399 RAC. For illustration purposes, sample response values indicate a 5399 RAC on an Ethernet network with the IP address 192.9.200.62. The host system address is 192.9.200.55.

  • Page 12: Configuring The Remote Annex

    * read-write The 5399 RAC will accept SNMP sets only from sources using the community string q2cannex. You can further restrict the access by including the IP address of the Annex Manager or Quick2Config Annex host.

  • Page 13: Using Quick2Config Annex

    Choose Help > Contents or click on detailed information on using Quick2Config Annex. Configuring Security By default, the 5399 RAC allows unrestricted access. If you want to configure module security, refer to the Model 5399 Remote Access Concentrator Network Administrator’s Guide for UNIX for information on setting up security files such as acp_passwd and acp_userinfo.

  • Page 14: Connecting The Wan Ports

    When the WAN ports and security have been configured, you can connect the ports to the external lines. Plug the channelized T1, channelized E1 or ISDN PRI lines into the WAN interface ports on the front edge of the 5399 RAC module. 166-024-865 Rev. A...

Table of Contents