1. Manuals
  2. Brands
  3. Bay Networks Manuals
  4. Switch
  5. Centillion 100 00BASE-FX
  6. Reference

Bay Networks Centillion 100 00BASE-FX Reference

8/2-port etherspeed 10base-t/100base-fx switch module
Hide thumbs
1
2
3
4
5
6
7
8
9
Table of Contents

Advertisement

Quick Links

Download this manual
Reference for the
Centillion 100
8/2-port EtherSpeed
10BASE-T/100BASE-FX

Switch Module

Part No. 893-00994-A
May 1997

Advertisement

Table of Contents
loading

Related Manuals for Bay Networks Centillion 100 00BASE-FX

Summary of Contents for Bay Networks Centillion 100 00BASE-FX

  • Page 1: Switch Module

    Reference for the Centillion 100 8/2-port EtherSpeed 10BASE-T/100BASE-FX Switch Module Part No. 893-00994-A May 1997...
  • Page 2 Declaration of Conformity For information about installing and troubleshooting Centillion 100 EtherSpeed Using the Centillion 100 EtherSpeed Switch Modules (Bay Networks part number 893-890-B). Refer to Using SpeedView 2.1 for Windows (Bay Networks part number 893-891-B) for information about how to use SpeedView ™...

  • Page 3: Status Leds

    2). Each fiber port has a correspondingly numbered LED. 100 Mb/s fiber port LEDs Figure 2. EtherSpeed 10BASE-T/100BASE-FX Switch Module LEDs Each numbered LED turns on, turns off, or blinks to indicate link status and/or data activity as described in Table Table 1.

  • Page 4: Default Configuration

    Default Configuration Table 2 lists the factory defaults for ports on the EtherSpeed module. Table 2. Factory defaults for EtherSpeed 10/100 Mb/s ports Parameter Factory default Switching mode Transparent Spanning Tree Protocol None Path cost Port partition state Enabled Filters Disabled PMD type •...
  • Page 5 UTP Port Requirements The RJ-45 connectors for the 10BASE-T ports accept standard unshielded twisted pair (UTP) cable and are wired as MDI-X ports to connect end stations without using crossover cables. Use 100-ohm Category 5 UTP cable with RJ-45 plugs on each end of the UTP cable. Table 3 shows the pin assignments for 10BASE-T UTP ports in the standard MDI-X configuration.

  • Page 6: Technical Specifications

    Technical Specifications Network Protocol and Standards Compatibility IEEE 802.3 for 10 Mb/s ports IEEE 802.3u for 100 Mb/s ports Data Rate 100 Mb/s Interfaces SC fiber optic connectors for 100BASE-FX Ethernet RJ-45 (8-pin modular) connectors for 10BASE-T Ethernet Microprocessors Baseboard: 64-bit MIPS 4700 series processor, 133 MHz Memory Processor:...
  • Page 7 Environmental Specifications Operating temperature: 0 to 40 C Storage temperature: –25 to 70 C Operating humidity: 85% maximum relative humidity, noncondensing Storage humidity: 95% maximum relative humidity, noncondensing Operating altitude: 10,000 ft (3,000 m) maximum Storage altitude: 10,000 ft (3,000 m) maximum Free fall/drop: ISO 4180-s, NSTA 1A Vibration:...

  • Page 8: Declaration Of Conformity

    Declaration of Conformity The following Declaration of Conformity for the Centillion 100 8/2-port EtherSpeed 10BASE-T/ 100BASE-FX Switch Module identifies the product, the Bay Networks name and address, and the applicable specifications that are recognized in the European community.
  • Page 9 © 1997 by Bay Networks, Inc. All rights reserved. Trademarks Bay Networks is a registered trademark of Bay Networks, Inc. Centillion 100, EtherSpeed, and SpeedView are trademarks of Bay Networks, Inc. Other brand and product names are registered trademarks or trademarks of their respective holders. Statement of Conditions In the interest of improving internal design, operational function, and/or reliability, Bay Networks, Inc.

This manual is also suitable for:

Centillion 100

Table of Contents