1. Manuals
  2. Brands
  3. DIGITIZE Manuals
  4. Controller
  5. System 3500
  6. Installation and operation manual

DIGITIZE SYSTEM 3500 Installation And Operation Manual

Network controller
Hide thumbs Also See for SYSTEM 3500:
Table of Contents

Advertisement

Quick Links

Download this manual
SYSTEM 3500 NETWORK CONTROLLER
INSTALLATION and OPERATION
Digitize, Inc.
158 Edison Road
Lake Hopatcong, New Jersey 07849
Tel:
(973) 663-1011
Fax:
(973) 663-4333
E-Mail:
<info>@digitize-inc.com
Website: http://www.digitize-inc.com
MANUAL
Part Number:
700232-0001
Issue Revision:
A
Issue Date:
02/00

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SYSTEM 3500 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for DIGITIZE SYSTEM 3500

Summary of Contents for DIGITIZE SYSTEM 3500

  • Page 1 SYSTEM 3500 NETWORK CONTROLLER INSTALLATION and OPERATION MANUAL Digitize, Inc. 158 Edison Road Lake Hopatcong, New Jersey 07849 Tel: (973) 663-1011 Fax: (973) 663-4333 Part Number: 700232-0001 E-Mail: <info>@digitize-inc.com Issue Revision: Website: http://www.digitize-inc.com Issue Date: 02/00...
  • Page 2 TRADEMARKS DIGITIZE (stylized) is a registered trademark of Digitize, Inc. All of the above are trademarks of Digitize, Inc. Any logos or product names mentioned in this document may be trademarks and are used for identification purposes only.
  • Page 3 FAX: (973) 663-4333 Website: http://www.digitize-inc.com This manual has been prepared by DIGITIZE, INC. for use by its licensees, distributors and customers. The information contained herein is the property of DIGITIZE, INC. and may not be copied, disclosed or reproduced, in whole or in part, without the prior written approval of DIGITIZE, INC. Any unauthorized disclosure to, or use of the enclosed information by, unauthorized third persons shall void any and all representations, warranties and obligations on the part of DIGITIZE, INC.
  • Page 5 FCC NOTICE In compliance with Paragraph 15.105 of the FCC Rules and Regulations, the following notice is pro- vided. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protec- tion againste harmful interference when the equipment is operated in a commercial environment.

  • Page 7: Table Of Contents

    Table of Contents SECTION 1 GENERAL INFORMATION 1.1. SYSTEM DESCRIPTION ......................1-1 1.2. NETWORK CONTROLLER ..................... 1-1 1.3. DISPLAY (FIGURE 1) ......................1-2 1.4. MEMORY ..........................1-2 1.4.1. MEM-600 MEMORY CHIP ..................1-2 1.4.2. MBD-4800 MEMORY MOTHERBOARD ..............1-4 1.5. SPECIFICATIONS ........................1-4 1.5.1.
  • Page 8 3.4.2. DC POWER ........................3-1 3.4.3. POWER TRANSFER ....................3-2 3.5. PROGRAM INITIALIZATION ....................3-2 3.6. CONNECTIONS AND SETTINGS ................... 3-3 SECTION 4 USER TEXT 4.1. USING THE EXTERNAL KEYBOARD .................. 4-1 4.1.1. GENERAL ........................4-1 4.1.2. INITIAL SET-UP ......................4-1 4.1.3.
  • Page 9 6.3.5. TAKING A ZONE TEMPORARILY OUT OF SERVICE ........... 6-9 6.3.7. INITIATING STATUS PRINTOUT FOR NON-SECURE ZONES ......6-9 6.3.8. CHECKING STATUS/MESSAGE OF INDIVIDUAL ZONE ........6-9 6.3.10. CHANGING THE PAPER TAPE ................6-9 6.3.11. SERIAL OUTPUT FROM THE SYSTEM 3500 NETWORK CONTROLLER ..6-10...
  • Page 10 9.2.2. UPLOAD COMMAND ....................9-4 9.2.3. RUN COMMAND ......................9-5 APPENDIX A USER TEXT STEP-BY-STEP PROCEDURES ........A-1 APPENDIX B SYSTEM 3500 NETWORK CONTROLLER SET MENUS STEP-BY-STEP PROCEDURES ............B- 1 APPENDIX C INSTALLATION DRAWINGS SYSTEM 3500 NETWORK CONTROLLER ............C-1...

  • Page 11: Section 1 General Information

    1.2. NETWORK CONTROLLER The overall unit is known as the SYSTEM 3500 Network Controller. The SYSTEM 3500 Network Controller is a totally solid state system that uses state of the art devices and circuitry to continuously monitor and display the status of all system connected alarms.

  • Page 12: Display (Figure 1)

    There are seven empty memory sockets available on the system supplied memory motherboard. Nonvolatile, nonmagnetic storage may be added to the SYSTEM 3500 Network Controller by installing memory modules and additional motherboards. Each of these is explained below.
  • Page 13 NETWORK CONTROLLER INSTALLATION AND OPERATION MANUAL Figure 1 - NETWORK CONTROLLER DISPLAY DIGITIZE, INC. 700232-A 02/00 1 - 3 Specifications Subject to Change Without Notice...

  • Page 14: Mbd-4800 Memory Motherboard

    4800 screens. The MBD-4800 contains all 4800 screens, and is installed in any of the card slots of the SYSTEM 3500 Network Controller. Each MBD-4800 has a DIP switch to allow you to set the address of the board. A total of eight motherboards may be installed in one system.

  • Page 15: Construction

    NETWORK CONTROLLER INSTALLATION AND OPERATION MANUAL 1.5.5. CONSTRUCTION The enclosure and cover of the SYSTEM 3500 Network Controller is made of 0.062" aluminum. A membrane keypad is mounted on a 0.093" aluminum front panel. 1.5.6. DIMENSIONS Height ............. 6.97" (17.7 cm) Width .............

  • Page 16: Display

    The SYSTEM 3500 Network Controller utilizes the CAPS II protocol. 1.7. FCC REQUIREMENTS The SYSTEM 3500 Network Controller complies with the limits set for a Class A computing device as specified in Subpart J of Part 15 of the Federal Communications Commission “Rules and Regulations”.

  • Page 17: Section 2 Installation

    Each unit has been thoroughly inspected prior to shipment. 2.2. INSTALLATION PROCEDURE The SYSTEM 3500 Network Controller is designed for 19 in. rack mounting and occupies seven inches of vertical rack space. Each unit has four mounting holes located on the front panel and is supplied with four special mounting washers in a small envelope attached to the front panel.
  • Page 18 NETWORK CONTROLLER INSTALLATION AND OPERATION MANUAL 2 - 2 DIGITIZE, INC 700232-A 02/00 Specifications Subject to Change Without Notice...

  • Page 19: Section 3 System Initialization

    Connect the branch circuit to a UL listed outlet box with duplex outlets, rigidly mounted in the bottom, per installation requirements of the National Electrical code and any local code. System 3500 is designed to be installed in a standard 19" equipment rack.

  • Page 20: Power Transfer

    ON and steady. AC failure and restoral will be annunciated and printed. 3.5. PROGRAM INITIALIZATION Upon power-up, the SYSTEM 3500 Network Controller will momentarily display the following screens, in sequence, while performing internal diagnostic tests: Awaiting Link...

  • Page 21: Connections And Settings

    Press “0” to accept no changes. If you are not sure whether or not to accept changes, press “0” to not accept changes. The system will then go into standard operation. During standard operation, the SYSTEM 3500 Network Controller will display the current date and time.

  • Page 22: Section 4 User Text

    Should a new unacknowledged ALARM, TROUBLE, or SECURE event occur while in the data entry mode, the SYSTEM 3500 Network Controller will automatically revert to the “Operator Mode” so that the new event may be processed. After the event has been processed and the ACK LED is no longer illuminated, the data entry mode can be re-entered by pressing any active key on the external keyboard.

  • Page 23: Access

    If the ESC key is pressed enough times it will completely back out of the Field Programmable mode, and into the SYSTEM 3500 Network Controller normal operation. It is, therefore, a valid alternative to pressing F1 when the operator wishes to exit the Field Programmable mode.

  • Page 24: External Keyboard Menu Selections

    NETWORK CONTROLLER INSTALLATION AND OPERATION MANUAL 4.2. EXTERNAL KEYBOARD MENU SELECTIONS Data for alarm points can be changed in the SYSTEM 3500 Network Controller via the external keyboard. In the data entry mode, the operator may ADD, CHANGE, or DELETE information based on options supplied with, or added to, the system.
  • Page 25 NETWORK CONTROLLER INSTALLATION AND OPERATION MANUAL Priority Level 8 is reserved for the SYSTEM 3500 Network Controller to automatically assign to any alarm that has no message programmed for it. Priority Level 8 also has significance should your system be expanded into a network configuration.

  • Page 26: User Text Types

    STU. The SYSTEM 3500 Network Controller identifies a zone specific or generic message by its STU number. The following are examples of generic and zone specific numbers.
  • Page 27 When STU 23-5 is received as an alarm, the display will bring up page 1 of the zone specific message in large type. The SYSTEM 3500 Network Controller will present the remainder of ther text messages in small type, just below the zone specific message. The small type messages appear in the following order: Page 1 of the generic (if any), page 2 of the generic (if any);...

  • Page 28: Generic

    ** FIRE 555-1234 POLICE 555-3333 SHUT OFF VALVE CORNER ELM AND BROAD ST The user may press the ZONE LOOK UP key on the SYSTEM 3500 Network Controller to view the other pages of text messages. After pressing ZONE LOOKUP, the SYSTEM 3500 Network Controller will present the text screens in this order: Page 1 of the zone specific, page 1 of the generic (if any), page 2 of the generic (if any);...

  • Page 29: Changing Zone Text

    234-. Generic messages are displayed on the SYSTEM 3500 Network Controller by pressing the LOOK UP key on the front panel. When the SYSTEM 3500 Network Controller displays a generic message (as part of a zone specific condition) the fourth line of the display will contain an underline across the entire display.

  • Page 30: Deleting Zone Text

    (if any exist) will decrement by one page number. The ESC key may be used at any time to abort the DELETE mode (prior to pressing F10). DIGITIZE, INC 700232-A 02/00 4 - 9 Specifications Subject to Change Without Notice...

  • Page 31: Password Menu

    To change the master password, enter “4”, then press the RETURN (or ENTER) key. The display will read: ENTER OLD MASTER PASSWORD TO BE CHANGED ENTER ___________ 4 - 10 DIGITIZE, INC 700232-A 02/00 Specifications Subject to Change Without Notice...

  • Page 32: Exit Data Entry Mode

    4.3.9. EXIT DATA ENTRY MODE When data entry mode is complete, press F1 to exit. You may also exit the field program mode at any time by unplugging the external keyboard jack from the SYSTEM 3500 Network Controller. 4.3.10. TOTAL PAGES INSTALLED, USED, AND DELETED...

  • Page 33: Section 5 Front Panel Access

    Direct access to a specific menu is possible by entering the menu number and pressing the SET button. The following is a list of the directly accessible menus: DIGITIZE, INC. 700232-A 02/00 5 - 1 Specifications Subject to Change Without Notice...

  • Page 34: Front Panel Menus

    As described in the revolving message, pressing the FUNC button will select the screen shown and move the cursor to the first selection of that menu. Refer to Appendix B, SYSTEM 3500 Network Controller Set Menus Step-by-Step Procedures for detailed directions for each menu.
  • Page 35 ↑↓ keys to select day and month, enter the correct numeric data for date and year, then press the SET button to save when complete. DIGITIZE, INC. 700232-A 02/00 5 - 3 Specifications Subject to Change Without Notice...

  • Page 36: Alarm Level / Tone

    Enter “2” to discard any modifications made during this session; the system printer will report “SOUNDS UNCHANGED.” Enter “3” to revert to the original factory settings for all tones. 5 - 4 DIGITIZE, INC. 700232-A 02/00 Specifications Subject to Change Without Notice...

  • Page 37: Thermal Printer Intensity

    FUNC button to move to the next field, then use the ↑↓ keys to step through the available settings. Press the CLEAR button to exit this menu. DIGITIZE, INC. 700232-A 02/00 5 - 5 Specifications Subject to Change Without Notice...

  • Page 38: In/Out Service Password Yes/No

    To change a password requirement to YES or NO, select the desired level screen, and press FUNC twice. The underline should now be at the first character of YES or NO. Use the ↑↓ keys on the SYSTEM 3500 Network Controller keypad to toggle the word from YES to NO or NO to YES.

  • Page 39: Status Printout Setup Mode

    The revolving message will read: <<Use ↑↓ keys to change value. Use FUNC to move to next field. Press CLEAR to end. All changes are accepted when entered. DIGITIZE, INC. 700232-A 02/00 5 - 7 Specifications Subject to Change Without Notice...

  • Page 40: Section 6 Operation

    “User Text” message exists for a dialer account number, a “canned” message will be displayed. The DIALER LOOK UP button may also be used to view the subsequent pages of “User Text” for any dialer account currently displayed. DIGITIZE, INC. 700232-A 02/00 6 - 1 Specifications Subject to Change Without Notice...

  • Page 41: Zone Look Up

    Press the FUNC button to print out a list of the available functions in your system. For example, to print out the program revision in the system, enter ‘‘10,’’ then press FUNC . The thermal printer will now print out the system revision number. 6.1.11. SET BUTTON 6 - 2 DIGITIZE, INC. 700232-A 02/00...

  • Page 42: On / - Button

    However, if the button is held in too long (approximately 60 seconds), the SYSTEM 3500 Network Controller will override the button and display any new conditions if they exist.

  • Page 43: Shift Key ( )

    As an example, to enter 123-E9. Press “1” “2” “3” “-” “SHIFT” “5” “9”. The SHIFT 5 will enter the hexadecimal value “E”. In some SYSTEM 3500 Network Controller units the STATUS key is the second function of the PAPER ADVANCE key.

  • Page 44: History

    OUT OF SERVICE. 6.1.20. SCROLL KEYS Upon activation of an Alarm, Trouble, or Restore condition, the SYSTEM 3500 Network Controller will automatically display all generic and zone specific messages (if any). If the item currently displayed in bold text has multipage pages, a SNGL/MULT PAGE DISP key will appear.

  • Page 45: Sngl/Multi

    Located just inside the printer door, on the right hand side, this button will restart the unit if the program should stop for any reason. If the SYSTEM 3500 Network Controller should stop running, a built-in watchdog timer will turn on a Trouble Buzzer in 4 seconds. Try to...

  • Page 46: Alarm Indicator

    When an alarm is actuated, the user programmed priority level will determine the response of the SYSTEM 3500 Network Controller. Of course if only one alarm is active, it will be displayed and processed regardless of the priority level. If this alarm is not acknowledged, and a higher priority alarm comes in, the higher priority alarm will replace the lower priority alarm on the screen.

  • Page 47: Normal Quiescent Operation

    NOTE: A new ALARM will automatically take priority over any TROUBLE condition. 6.3.2. NORMAL QUIESCENT OPERATION Under normal condition, the SYSTEM 3500 Network Controller displays the current date and time on the lower line of the screen. 6.3.3. ALARM CONDITION...

  • Page 48: Taking A Zone Temporarily Out Of Service

    Then switch the ON/ STBY switch to the STBY position. Refer to the diagram located inside the unit, under the printer mechanism. DIGITIZE, INC. 700232-A 02/00 6 - 9 Specifications Subject to Change Without Notice...

  • Page 49: Serial Output From The System 3500 Network Controller

    6.3.11. SERIAL OUTPUT FROM THE SYSTEM 3500 NETWORK CONTROLLER Data on the alarms into the SYSTEM 3500 Network Controller can be sent out over a two- wire serial data link. One such use is Computer Aided Dispatch. The output is based on standard data output format with a selection of preset BAUD rates from 150 to 9600.

  • Page 50: Section 7 Derived Channel Network Controller

    Contact the factory for details on the Network Receiver. The DCX scanner can be controlled with a single SYSTEM 3500 Network Controller via two data links or two SYSTEM 3500 Network Controllers with a single data link per SYSTEM 3500 Network Controller to the scanner.

  • Page 51: Initialization And Port Settings

    Failure of one or more XR’s will not break communication. Up to 16 XR cards are installed in each scanner. Scanners are communications controllers located at the telephone exchange. If the SYSTEM 3500 Network Controller has already recognized and read the XR card, when the thermal printer prints the Derived Channel details the second line will read: XR= 1XXXXXXX XXXXXXXX where 1= Installed and X=Not Installed.

  • Page 52: Derived Channel Setup Screen

    The System reports each downed link as it occurs. The system will operate normally if one link is down. However, if both links are down, the SYSTEM 3500 Network Controller sends a third message alerting the operator that the system is totally down.

  • Page 53: Password

    It is recommended that the supervisor select ‘2’ to verify that all Global Settings are correct. If Global Settings are correct there is no action required. If the Global Settings have never been set, or if they must be changed, select ‘2’. 7 - 4 DIGITIZE, INC. 700232-A 02/00 Specifications Subject to Change Without Notice...

  • Page 54: Global Settings

    Channel B to the scanner. When using two Systems, one System can communicate to the scanner on Channel A and the other System can communicate via Channel B. The ‘extra’ channel on each System is then used to communicate to the other SYSTEM 3500 Network Controller. This is the ‘Cross Unit’ feature.
  • Page 55 Pressing the ADD STU key will add the STU to EEPROM memory in the SYSTEM 3500 Network Controller only. In order to make the STU operational, the operator must press the UP STU programmable key. Or, press the UP STU key via the Derived Channel Programmable keys.

  • Page 56: Derived Channel Programmable Keys (Figure 7-1)

    7.5 DERIVED CHANNEL PROGRAMMABLE KEYS (FIGURE 7-1) The Derived Channel Network Option utilizes the factory programmable keys located on the bottom of the SYSTEM 3500 Network Controller display. Refer to Figure 7-1for a listing of all Derived Channel programmable keys.

  • Page 57: Stu Info Keys

    START POLL sends a query to the scanner to update the status of all STUs (one every 20 seconds) until all STUs have reported. This allows the SYSTEM 3500 Network Controller to verify that it’s database matches that of the scanner.
  • Page 58 LOAD SIM provides scanner with information about which STU is connected to a given STU card. LIST STU DISP permits the operator to list the STU connected to the SYSTEM 3500 Network Controller. The STU can be accessed by the STU #, the HID # or the telephone number.
  • Page 59 NETWORK CONTROLLER INSTALLATION AND OPERATION MANUAL 7 - 10 DIGITIZE, INC. 700232-A 02/00 Specifications Subject to Change Without Notice...

  • Page 60: Section 8 Computer Interface Options

    Also sent via the serial port are any System errors. These errors include AC power fail, ribbon cables removed, data links down, etc. The BAUD rate and Parity, as well as the number of data and stop bits, are user programmable via the SET features of all SYSTEM 3500 Network Controller units.

  • Page 61: Type Number

    The CONDITION is a seven character string. It will always be either “ALARM / /”, “TROUBLE” or “SECURE /”. 8.4. CAPS PLUS Standard CAPS option has been expanded and includes handshake capability between computer and SYSTEM 3500 Network Controller to provide supervision. NUMBER OF CHARACTERS PER BLOCK 0Ah P-1 20H MESSAGE TYPE TYPE NUMB...

  • Page 62: Section 9 Uploading New Software Versions

    UPLOADING NEW SOFTWARE VERSIONS 9.1 OVERVIEW The CPU VI provides the SYSTEM 3500 Network Controller with a RS-232 serial port to be used to upload new program versions to the unit. The serial port is connected to the CPU VI by a 9- conductor plug-in ribbon cable.
  • Page 63 Attempting to establish link on COM1 Choose another COM port Quit connection attempt Press reset switch on the System 3500 now to establish the link-up. COM1 now connected Configure COM port and sync with System 3500 If you need to select another COM port, Press ‘C’, the PC screen will display:...

  • Page 64: Save Command

    After pressing any key, the next screen will display: SYSTEM 3500 UTILITIES PACKAGE Quit back to MSDOS Link Status Link PC to SYSTEM 3500 (reconnect) SYS3000 Kernel Version: 1.00 Upload new program to SYSTEM 3500 Save program from SYSTEM 3500...

  • Page 65: Upload Command

    Get Program from SYSTEM 3500 Network Controller and save to disk. 9.2.2. UPLOAD COMMAND When the Save is completed, Press U to upload the new program to the SYSTEM 3500 Network Controller. The PC screen will now display: SYSTEM 3500 Network Controller UTILITIES PACKAGE...

  • Page 66: Run Command

    Link Status portion of the screen. 9.2.3. RUN COMMAND Press R to run program in the SYSTEM 3500 Network Controller. The link between the PC and the SYSTEM 3500 Network Controller will be broken. Pressing the reset switch inside the SYSTEM 3500 Network Controller will also sever the link.

  • Page 67: Appendix A User Text Step-By-Step Procedures

    APPENDIX A USER TEXT STEP-BY-STEP PROCEDURES DIGITIZE, INC. 700232-A 02/00 APPENDIX A - 1 Specifications Subject to Change Without Notice...
  • Page 68 APPENDIX A - 2 DIGITIZE, INC. 700232-A 02/00 Specifications Subject to Change Without Notice...
  • Page 69 ENTER _________ ENTER 12 (RET) ENTER 12 (RET) (type desired (type desired) changes user message) user message) CHANGE ZONE ADD ZONE PRESS F10 PRESS F10 (CONTINUE) DIGITIZE, INC. 700232-A 02/00 APPENDIX A - 3 Specifications Subject to Change Without Notice...
  • Page 70 LEVEL 1 from 1 (1 - 255) ENTER _____ END FIELD PROG ESC = PREVIOUS F1 = GET OUT llllll PRESS 2 (RET) MAKE SELECTION _ APPENDIX A - 4 DIGITIZE, INC. 700232-A 02/00 Specifications Subject to Change Without Notice...

  • Page 71: Set Menus Step-By-Step Procedures

    APPENDIX B SYSTEM 3500 NETWORK CONTROLLER SET MENUS STEP-BY-STEP PROCEDURES DIGITIZE, INC. 700232-A 02/00 APPENDIX B - 1 Specifications Subject to Change Without Notice...
  • Page 72 5. PRINT indicates PRESS PRINT to obtain a listing on thermal printer of options already set. 6. << indicates the scrolling message, which provides directions to users. APPENDIX B - 2 DIGITIZE, INC. 700232-A 02/00 Specifications Subject to Change Without Notice...
  • Page 73 << Enter numeric value 8 SET DDI-7/8 IN/OUT SERVICE Q-MUX SETUP 16 SET SET UP MODE 24 SET PASSWORD ON/OFF (NEEDS OPTION) DEFINE PRI LEVEL (NEEDS OPTION) DIGITIZE, INC. 700232-A 02/00 APPENDIX B - 3 Specifications Subject to Change Without Notice...
  • Page 74 18:02:30 TIME 4:28:30A PRESS ↑ PRESS SET TO SAVE TIME AND EXIT SET MODE << Use ↑↓ keys to MODE = PM TIME 4:28:38P PRESS ↑ APPENDIX B - 4 DIGITIZE, INC. 700232-A 02/00 Specifications Subject to Change Without Notice...
  • Page 75 << Use ↑↓ keys to TODAY IS FRI TODAY IS FRI FEB 27, 1991 JAN 24, 1990 PRESS SET TO SAVE NEW DATE AND EXIT SET MODE DIGITIZE, INC. 700232-A 02/00 APPENDIX B - 5 Specifications Subject to Change Without Notice...
  • Page 76 << Use keys to ↑↓ << Use keys to BUZZ TONE=B22 SECUR TONE=180 VF=2 ENV=1 VF=4 VR=4 TIME ON=28 AMT OFF=88 ON=20 PRESS ↑ PRESS ↑ APPENDIX B - 6 DIGITIZE, INC. 700232-A 02/00 Specifications Subject to Change Without Notice...
  • Page 77 7. CLICK is keypad click, BEEP & BUZZ are system responses to keypad entries. These sounds are front panel only. 8. VF = volume front, VR = volume rear. In addition to master volume adjustment inside System 3500, volume is user adjustable in 15 steps. DIGITIZE, INC. 700232-A 02/00 APPENDIX B - 7...
  • Page 78 <<With KBD-2 type 16 LOW PAPER = OFF 143.6' TO ->->EMPTY PRINT INTENSITY 4 PRINTER INTENSITY SELECTION MIN, 1 through 14, MAX, selectable using ↑↓ keys APPENDIX B - 8 DIGITIZE, INC. 700232-A 02/00 Specifications Subject to Change Without Notice...
  • Page 79 4. STOP BITS - 1 & 2 5. SYSTEM 3500 is shipped with four serial ports installed. User must add configurator cards to adapt output to RS-232, RS-422, Current Loop, Audio Modem, Fiber Optic or Radio Polling. Serial ports are not operational unless a serial option is ordered.
  • Page 80 2. User text area = User can enter any 16 alpha-numerica character to describe the location of the DGM panel. Press FUNC to move curser to start of third line, insert External Keyboard and type desired 16 character message. 3. oP =Press PRINT for DGM list. APPENDIX B - 10 DIGITIZE, INC. 700232-A 02/00 Specifications Subject to Change Without Notice...
  • Page 81 ENTER 12 ,,,,,,, PRESS SET PRESS SET ENTER 2 PRESS CLEAR PRESS CLEAR SYNC TIME/DATE FROM MASTER 1=YES 2=NO ENTER _ llllllll ENTER 1 or 2 DIGITIZE, INC. 700232-A 02/00 APPENDIX B - 11 Specifications Subject to Change Without Notice...
  • Page 82 IN / OUT service use password? use password? PRESS ↑ << Use ↑↓ keys to LEV 5 "INDUST " IN / OUT service use password? PRESS ↑ APPENDIX B - 12 DIGITIZE, INC. 700232-A 02/00 Specifications Subject to Change Without Notice...
  • Page 83 << Enter number o << Enter number o SST SLOW SPEED SST FAST SPEED PREFIX = AS IS PREFIX = AS IS 0=AS IS 1=COMBIN 0=AS IS 1=COMBIN DIGITIZE, INC. 700232-A 02/00 APPENDIX B - 13 Specifications Subject to Change Without Notice...
  • Page 84 LIMIT TO X RNDS FROM 23:00-23:59 Notes: Allows user to set how many rounds to retransmit based on time of day. Allows user to set ‘transmit after what round’. APPENDIX B - 14 DIGITIZE, INC. 700232-A 02/00 Specifications Subject to Change Without Notice...
  • Page 85 ENTER ****______ ENTER _________ PRESS CLEAR AT ANY TIME TO ABORT ↑↓ << Use keys to RADIO BOX (1221) CARRIER ALM=15 S NEG BX only= NO DIGITIZE, INC. 700232-A 02/00 APPENDIX B - 15 Specifications Subject to Change Without Notice...
  • Page 86 << Enter number o 1221 RAD TEST BX 1221 RAD TEST BX ADD TEST DIALER DEL TEST DIALER ENTER 123-E9___ ENTER 123-E9___ PRESS SET PRESS FUNC APPENDIX B - 16 DIGITIZE, INC. 700232-A 02/00 Specifications Subject to Change Without Notice...
  • Page 87 PRESS CLEAR AT ANY TIME TO ABORT PRINT BASED ON 1ST IN - 1ST OUT PRINT DATE= NO PRESS ↑ PRINT BASED ON TYPE CONDITION PRINT DATE=NO DIGITIZE, INC. 700232-A 02/00 APPENDIX B - 17 Specifications Subject to Change Without Notice...
  • Page 88 UP ARROW USE PASSWORD? N USE PASSWORD? Y USE PASSWORD? Y GROUP #1 GROUP #1 GROUP #1 θP ZN _________ θP ZN _________ θP ZN _________ APPENDIX B - 18 DIGITIZE, INC. 700232-A 02/00 Specifications Subject to Change Without Notice...
  • Page 89 AFTER ENTERING ALL VALUES FOR PRINTER #1, PRESS FUNC TO RETURN TO FIRST PRINTER SCREEN, AND ENTER VALUES FOR PRINTER #2, ETC. PRESS CLEAR AT ANY TIME TO ABORT. DIGITIZE, INC. 700232-A 02/00 APPENDIX B - 19 Specifications Subject to Change Without Notice...
  • Page 90 θP CONFIG # 1 ZONE|ALM|TRB|SEC PROCESS | FOR 01 | 01 | -- | 21 DAILY TEST | -- PRESS CLEAR AT ANY TIME TO ABORT APPENDIX B - 20 DIGITIZE, INC. 700232-A 02/00 Specifications Subject to Change Without Notice...
  • Page 91 PAGER#_ _ _ _ _ _ _ _ _ PHONE# _ _ _ _ _ _ _ _ _ DO NOT PAGE PRESS CLEAR AT ANY TIME TO ABORT DIGITIZE, INC. 700232-A 02/00 APPENDIX B - 21 Specifications Subject to Change Without Notice...
  • Page 92 SET UP MODE oENTER_________g ↑↓ <<Use keys to ABM DCC-3500 USE OPER ACK= NO USE ABM O/S = NO PRESS CLEAR AT ANY TIME TO ABORT APPENDIX B - 22 DIGITIZE, INC. 700232-A 02/00 Specifications Subject to Change Without Notice...
  • Page 93 SET UP MODE ∗∗∗∗ oENTER_________g oENTER ___g ↑↓ <<Use the keys to TELG/DD AUTO CLR AUTO CLEAR BX/DD IN XX SEC PRESS CLEAR AT ANY TIME TO ABORT DIGITIZE, INC. 700232-A 02/00 APPENDIX B - 23 Specifications Subject to Change Without Notice...
  • Page 94 20 SET NOT USED AT THIS TIME ENTER 20, PRESS SET APPENDIX B - 24 DIGITIZE, INC. 700232-A 02/00 Specifications Subject to Change Without Notice...
  • Page 95 ___g ↑↓ <<Use keys to MARK VI TX (1221) BOX FORMAT = 4-2 99 ZONE BOX 5-2 PRESS CLEAR AT ANY TIME TO ABORT DIGITIZE, INC. 700232-A 02/00 APPENDIX B - 25 Specifications Subject to Change Without Notice...
  • Page 96 SET UP MODE ∗∗∗∗ oENTER ___g oENTER_________g ↑↓ <<Use the keys to MOMENTARY=2 SEC PPO-64 PT OUTPUT DEFAULT= MOMENTRY PRESS CLEAR AT ANY TIME TO ABORT APPENDIX B - 26 DIGITIZE, INC. 700232-A 02/00 Specifications Subject to Change Without Notice...
  • Page 97 VIA ZUX RELAY ∗∗∗∗ oENTER ___g oENTER_________g ↑↓ <<Use keys to ALM/TRB RELAY ALM RLY ON PRI PRI LEV = 12345678 PRESS CLEAR AT ANY TIME TO ABORT DIGITIZE, INC. 700232-A 02/00 APPENDIX B - 27 Specifications Subject to Change Without Notice...
  • Page 98 θP Q-MUX SETUP NODE # 9001 ACTIV ID # 1 Q-1R DISP Select ID Module: Q-1C Q-1CL Q-I/O Q-1R Q-EOL ARM/DISARM C/INTELGNC NONE After selection, press FUNC APPENDIX B - 28 DIGITIZE, INC. 700232-A 02/00 Specifications Subject to Change Without Notice...
  • Page 99 REQUIRE PASSWORD=NO PRESS FUNC ↑↓ << Use the keys to DCX NETWORK CONTROLLER CHANNEL A=TO SCANNER CHANNEL B=TO SCANNER CONNECTED TO SCANNER # ___1 REQUIRE PASSWORD=NO DIGITIZE, INC. 700232-A 02/00 APPENDIX B - 29 Specifications Subject to Change Without Notice...
  • Page 100 APPENDIX C INSTALLATION DRAWINGS SYSTEM 3500 NETWORK CONTROLLER DIGITIZE, INC. 700232-A 02/00 APPENDIX D - 1 Specifications Subject to Change Without Notice...
  • Page 101 Digitize’s products by salesmen, dealers, distributors or agents, unless confirmed in writing by a Digitize officer. If the firmware or hardware is altered or modified by the Buyer, this firmware and hardware is not covered within this limited warranty and the Buyer bears sole responsibility and liability for that firmware and hardware.

Table of Contents