Related Manuals for SeeEyes SC-IPC1201TW
Summary of Contents for SeeEyes SC-IPC1201TW
- Page 1 Release Version 1.0 1Channel 2-wire IP Transmission System SC-IPC1201TW User’s Manual SC-IPT1201TW SC-IPR1201TW...
-
Page 2: Safety Warnings And Cautions
Release Version 1.0 Safety Warnings and Cautions This is to protect user safety and prevent property damage. Please read it carefully and use it correctly. Warning (If not observed, the user may be killed or seriously injured.) ■ Be sure to unplug the power cord before installation. Also, do not plug in multiple power plugs at the same time. - Page 3 Release Version 1.0 Caution (If this is not observed, the user may be injured or property damage may occur.) ■ It is recommended that the ambient temperature and humidity be appropriate. - Avoid places where the temperature is too high (over 50°C) or too low (below -10°C) or where there is a lot of humidity.
- Page 4 Release Version 1.0 1. Introduction 1-1. Overview This product is composed of SC-IPT1201TW and SC-IPR1201TW as an IP power superimposition device (supplying camera power through PoE by sending/receiving 2-Wire). Since it is equipped with a power superimposition function, it is possible to supply power to the transmitter and camera, so there is no need for separate power construction.
- Page 5 Release Version 1.0 3. Product Parts & Functions 3-1. SC-IPT1201TW ④ ① ② ② ③ ⑤ ① Receiver Side: Receiver connection terminal and video output terminal. ② Status LED location designation LED status indication function lights out Not Link LINK Orange Steady/Flashing Link Check 및...
- Page 6 Release Version 1.0 3-2. SC-IPR1201TW ① ② ③ ④ ④ ① Transmitter Side : Transmitter connection terminal and video input terminal. ② Status display LED designation LED status indication function lights out Not Link Orange Link Check and Link Retry LINK Steady/Flashing Green...
-
Page 7: Connection Diagrams
Release Version 1.0 4. Connection Diagrams 4-1. Power supply with PoE HUB (CAM PoE SW ON) MAX : 700m @ TP Cable (based on 10Mbps FD) (When camera power is supplied separately or when Extra Power is supplied to the transmitter) 4-2. - Page 8 Release Version 1.0 5. Transmission distance per cable 5-1. 1 vs 1 Connecting to configuration product SC-IPC1201TW maximum transmission distance Max. 700m (TP-Cable @ CAT.5e) specification Maximum Power Available Max. 30W input power DC 48V/1.04A bandwidth (TCP/IP) 56V/1.2A transmission cable type...
-
Page 9: Troubleshooting Method
Release Version 1.0 6. Troubleshooting method Condition Check Method • Check the adapter connections. • Make sure that the dedicated adapter is used. No power • Check whether the product's PWR LED is operating normally. • Check the cable connections. •... -
Page 10: Product Specification
Release Version 1.0 7. Product specification MODEL SC-IPT1201TW power output Midspan PoE support (Type B only, PoE SW can be On/Off) transmission bandwidth 1Gbps (PHY RATE) RECEIVER SIDE Terminal Block(24 ~ 12AWG) access port CAMERA SIDE RJ-45 (TIA/EIA568B Type) EXTRA POWER IN DC-Jack 1Pin: TX +, 2Pin: TX-, 3Pin: RX+, 4Pin: PWR+ RJ-45 Connector... -
Page 11: Warranty Certificate
Release Version 1.0 8. Warranty Certificate Product No. Model No. Date of Purchase Place of Purchase Name Purchaser Address & Contact No. Name Distributor Address & Contact No. Warranty Period Two(2) years from the date of purchase Any failure that occurs in the normal use for only two years after purchase will be repaired free of charge. - Page 12 Release Version 1.0 SeeEyes Co., Ltd #503~509, 511~512, Sunil Technopia, 555 Dunchon-daero, Jungwon-gu, Seongnam City, Gyeonggi Province, Korea (Zip Code: 13215) TEL: +82-(0)31-730-5833 FAX: +82-(0)31-777-3512 EMAIL: overseas@sscctv.com http://www.sscctv.com/eng...
Need help?
Do you have a question about the SC-IPC1201TW and is the answer not in the manual?
Questions and answers