NEC UNIVERGE NEAX 2000 IPS System Manual
Internet protocol server
Hide thumbs
Also See for UNIVERGE NEAX 2000 IPS:
- Command manual (1038 pages) ,
- Installation manual (619 pages) ,
- System manual (448 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for NEC UNIVERGE NEAX 2000 IPS
Summary of Contents for NEC UNIVERGE NEAX 2000 IPS
- Page 1 SIP Trunk System Manual NWA-011436-001 ISSUE 3.0...
- Page 2 NEC Infrontia Corporation reserves the right to change the specifica- tions, functions, or features, at any time, without notice. NEC Infrontia Corporation has prepared this document for use by its employees and customers. The information contained herein is the property of NEC Infrontia Corporation and shall not be reproduced without prior written approval from NEC Infrontia Corporation.
- Page 3 ISSUE No. ISSUE No. PAGE No. PAGE No. ISSUE 1 ISSUE 2 ISSUE 3 ISSUE 4 DATE DECEMBER, 2005 DATE JULY, 2006 DATE APRIL, 2007 DATE ISSUE 5 ISSUE 6 ISSUE 7 ISSUE 8 DATE DATE DATE DATE NEAX 2000 IPS SIP Trunk System Manual Revision Sheet 1/2 NWA-011436-001...
- Page 4 ISSUE No. ISSUE No. PAGE No. PAGE No. ISSUE 1 ISSUE 2 ISSUE 3 ISSUE 4 DATE DECEMBER, 2005 DATE JULY, 2006 DATE APRIL, 2007 DATE ISSUE 5 ISSUE 6 ISSUE 7 ISSUE 8 DATE DATE DATE DATE NEAX 2000 IPS SIP Trunk System Manual Revision Sheet 2/2 NWA-011436-001...
-
Page 5: Table Of Contents
NEAX 2000 IPS SIP Trunk System Manual TABLE OF CONTENTS INTRODUCTION ........................PURPOSE ........................OUTLINE OF THIS MANUAL ..................TERMS IN THIS MANUAL ................... PBX SYSTEM DESIGNATION ..................... REFERENCE MANUAL ....................CHAPTER 1 GENERAL INFORMATION ................SYSTEM OUTLINE ...................... SERVICE CONDITIONS ....................SERVICE FEATURES .................... - Page 6 TABLE OF CONTENTS Fragmented IP Packet Receiving ..................Multiple CODEC Selection ....................Session Timer ........................NAT Support in SIP Trunk ....................Out-band DTMF ........................Source IP Address Check on SIP Trunk ................RTCP Function of SIP Trunk ....................SYSTEM DATA BACKUP ................... SYSTEM RESET ......................
-
Page 7: Introduction
INTRODUCTION PURPOSE/OUTLINE OF THIS MANUAL INTRODUCTION PURPOSE This manual explains the hardware installation and the programming procedure for providing SIP trunk system to the NEAX 2000 IPS System. OUTLINE OF THIS MANUAL This manual consists of four chapters. The following paragraphs summarize Chapters 1 through 4. CHAPTER 1 GENERAL INFORMATION This chapter explains the SIP trunk system outline, service conditions, and the... -
Page 8: Terms In This Manual
INTRODUCTION TERMS IN THIS MANUAL TERMS IN THIS MANUAL PBX SYSTEM DESIGNATION PBX system is designated as “PBX” or “system” usually. When we must draw a clear line between the PBX systems, they are designated as follows. 2000 IPS: NEAX 2000 IPS INTERNET PROTOCOL SERVER NOTE 1: In regard to China market, we have not released NEAX 2000 IPS INTERNET PROTOCOL SERVER but NEAX 2000 is released. -
Page 9: Reference Manual
INTRODUCTION REFERENCE MANUAL REFERENCE MANUAL During installation, refer also to the manuals below: System Manual: Contains the system description, hardware installation procedure and the programming procedure for the NEAX 2000 IPS System. Command Manual: Contains Customer Administration Terminal (CAT) operation, command functions and data re- quired for programming the system, and Resident System Program. - Page 10 THIS PAGE LEFT BLANK INTENTIONALLY. – 4 – NWA-011436-001 Rev.3.0 9ych0001.fm...
-
Page 11: Chapter 1 General Information
CHAPTER 1 GENERAL INFORMATION CHAPTER 1 GENERAL INFORMATION This chapter explains the SIP trunk system outline, service conditions, and the service features. SYSTEM OUTLINE ..............SERVICE CONDITIONS ............SERVICE FEATURES ............... – 5 – NWA-011436-001 Rev.3.0 9ych1001.fm... -
Page 12: System Outline
CHAPTER 1 GENERAL INFORMATION SYSTEM OUTLINE SYSTEM OUTLINE This system provides the IP phone service by TopLink with mounting SIP trunk on PBX. System Outline Router PSTN/ TopLink (IP) GSTN SIP trunk – 6 – NWA-011436-001 Rev.3.0 9ych1001.fm... -
Page 13: Service Conditions
CHAPTER 1 GENERAL INFORMATION SERVICE CONDITIONS SERVICE CONDITIONS SIP trunk system is available for Series 3600 software or later. The maximum number of the SIP card to be mounted is 8 per system including the CCH, CCT, IPT, and virtual IPT. Setting of alternate routing to C.O. -
Page 14: Service Features
CHAPTER 1 GENERAL INFORMATION SERVICE FEATURES SERVICE FEATURES The following is the features to be provided via SIP trunk for IP phone service. Alternate Routing Caller ID Display Direct Inward Dialing (DID) E.164 “+” Addition/Deletion Fault Registration Fragmented IP Packet Receiving Multiple CODEC Selection Session Timer Listed from next page are the service features provided by NEAX 2000 IPS. - Page 15 CHAPTER 1 GENERAL INFORMATION SERVICE FEATURES Method of origination operation PBX originates a call with LCR Number Development. Holding/Transferring features Holding/Transferring features are not available with SIP method. Setting Ringing Tone The ringing tone for SIP transmission can be set by CM08>649. NOTE: All the types of the called numbers are handled similarly on the PBX.
- Page 16 CHAPTER 1 GENERAL INFORMATION SERVICE FEATURES List of PBX Service Features ×: Available –: Not available ∆: Out of Target term term term SERVICE FEATURES REMARKS SP30 × × × × × Hot Line-OUTSIDE × × × × × Call Hold ×...
- Page 17 CHAPTER 2 INSTALLATION CHAPTER 2 INSTALLATION This chapter explains the required equipment and the hardware installation procedure to the SIP trunk system. PRECAUTIONS ................. REQUIRED EQUIPMENT ............INSTALLATION PROCEDURE ..........– 11 – NWA-011436-001 Rev.3.0 9ych2001.fm...
- Page 18 CHAPTER 2 INSTALLATION PRECAUTIONS PRECAUTIONS Static Electricity Guard You must wear a grounded wrist strap to protect circuit cards from static electricity. Static Electricity Guard • WHEN PLUGGING/UNPLUGGING A CIRCUIT CARD FRAME GROUND SCREW WRIST STRAP • WHEN HOLDING A CIRCUIT CARD NEVER TOUCH THE COMPONENTS OR SOLDERED SURFACE WITH BARE HANDS.
- Page 19 CHAPTER 2 INSTALLATION PRECAUTIONS Static Electricity Guard • WHEN MAKING A SWITCH SETTING ON A CIRCUIT CARD CIRCUIT CARD WEAR A WRIST STRAP AND PERFORM THE WORK ON A GROUNDED CONDUCTIVE WORK SURFACE. • WHEN CARRYING A CIRCUIT CARD CONDUCTIVE CIRCUIT POLYETHYLENE CARD...
- Page 20 CHAPTER 2 INSTALLATION PRECAUTIONS CAUTION 1. You must hold the edge of a circuit card when plugging or unplugging the circuit card. If you touch another area, you may be exposed to hazardous voltages. NEVER TOUCH THE COMPO- NENTS OR SOLDERED SUR- FACE WITH BARE HANDS.