Program Audio Output
Variable audio output — 3.5 mm, 5‑pole captive screw connector outputs the program audio (see
P
The level is controlled by the front panel volume encoder.
Balanced and unbalanced program audio output is available on the MPS 602 using a 3.5 mm,
5‑pole captive screw connector. Refer to the illustration for proper wiring.
ATTENTION:
•
For unbalanced audio, connect the sleeves to the ground contact. DO NOT connect the
sleeves to the negative (–) contacts.
•
Pour l'audio asymétrique, connectez les manchons au contact au sol. Ne PAS connecter
les manchons aux contacts négatifs (–).
NOTE:
Do not tin the audio leads. Tinned wires are not as secure in the connector and
could be pulled out. See below for wire stripping instructions.
100-240V
1.0A MAX
1
Mic Mix — One potentiometer controls the Mic/Line input level (
N
audio output (
O
) (see figure at right).
2
Fixed audio output — The bottom 3.5 mm, 5‑pole captive screw connector is for balanced or
O
unbalanced fixed level program audio output (see
50/60 Hz
audio level from this audio output port.
Amplified program audio output (SA and MA models only)
Q
MA models — One green 5 mm, 2‑pole locking captive screw connector for mono 70V output.
SA models — One green 5 mm, 4‑pole locking captive screw connector for amplified dual channel output to a 4 or 8 ohm
speaker system (see figure at right).
Strip and insert the speaker wires into the
1
connector and tighten the captive screws.
Be sure to observe the correct polarit
C L
1
Amplified Output Connector Wiring (SA and MA Models Only)
Figure 3.
Control
RS-232 remote — 3.5 mm, 3‑pole captive screw connector for connection of a host
R
computer, or a controller using Simple Instruction Set (SIS™). Wire the connector as
shown at right.
Reset button — With the MPS 602 on, press and release this recessed button (see figure at right,
S
4
the MPS 602 to the factory default settings.
RGB OUT
3
5
4
RGB OUT
3
5
O
y.
T
O U
P
A M
V
7 0
MPS 602 MA
G
I N
I R
2 W
S
A S
2
RS-232
IR
OUTPUTS
Tx
Rx G
Tx Rx
SELECT
6
OVER DTP
SIG
LINK
SIG
LINK
OVER DTP
RS-232
IR
DTP IN
DTP OUT
Tx
Rx G
Tx Rx
RS-232
IR
) mixed into the fixed program
G
OUTPUTS
SELECT
Tx
Rx G
Tx Rx
6
OVER DTP
SIG
LINK
SIG
LINK
OVER DTP
RS-232
IR
). The front panel knob does not control the
DTP IN
DTP OUT
Tx
Rx G
Tx Rx
2
Do not tin the wires!
Do not tin
the wires!
L
1
R
L
2
R
L
3
R
HDMI
L
4
R
L
5
R
MIC LINE
figure 1
on page 1).
Tip
Ring
Sleeves
Tip
Ring
Balanced Audio Output
No Ground Here
Tip
Sleeves
Tip
No Ground Here
Unbalanced Audio Output
L
1
R
L
2
R
L
3
R
HDMI
Do not tin the wires!
L
4
R
L
5
R
MIC LINE
Insert the wired connector into the amplifier
output and secure the locking screws on
either side.
T
O U
P
4 Ω
A M
/
R
8 Ω
MPS 602 SA
L
G
I N
I R
2 W
S
A S
C L
1
2
RS-232
Device
Bidirectional
Transmit (Tx)
Transmit (Tx)
Receive (Rx)
Receive (Rx)
Ground (
Ground (
)
L
R
VARIABLE
) to return
S
AMP OUT
REMOTE
8Ω / 4Ω
L
R
RS-232
L
R
FIXED
MIC
MIX
CLASS 2 WIRING
Tx Rx G
L
R
VARIABLE
AMP OUT
8Ω / 4Ω
R
L
L
R
FIXED
MIC
MIX
CLASS 2 WIRING
Tx
Rx
)
MPS 602 SA
R
3