EN-1 Ranger™ Count 3000 Series 1. INTRODUCTION 1.1 Definition of Signal Warnings and Symbols Signal Words CAUTION Note Warning Symbols 1.2 Safety Precautions 2. INSTALLATION 2.1 Package Contents ...
Page 4
EN-2 Ranger™ Count 3000 Series 2.2 Installing Components 2.3 Selecting the Location 2.4 Leveling the Equipment...
Page 5
Notes lo.bat CAUTION: Battery is to be replaced only by an authorized Ohaus service dealer. Risk of explosion can occur if the rechargeable battery is replaced with the wrong type or if it is not properly connected. Dispose of the lead...
Page 10
EN-8 Ranger™ Count 3000 Series Entering a known APW: ------ 3.3.3 Simple Counting Tare 3.4 Accumulation and Statistics 3.4.1 Accumulating Displayed Values 3.4.2 Viewing and Clearing Statistical Data Tare Clr.aCC Notes: When Legal for Trade is ON, the display must return to 0 gross. Otherwise, the ∑ pointer will continue flashing.
Page 11
EN-9 Ranger™ Count 3000 Series Tare 3.6 Check-Counting Target Target Check Count Target Under Over Tare Positive Check Negative Check Tare Zero Check Tare...
Page 12
EN-10 Ranger™ Count 3000 Series 3.7 Library Storing a record: Store Retrieving a record: reCall reCall Editing a record: reCall edit 000000 000000 save Clearing a record: reCall delete Printing Library record:...
EN-11 Ranger™ Count 3000 Series 4. MENU SETTINGS 4.1 Menu Navigation User Menu: C.A.L S.E.t.U.P r.E.A.d U.n.i.t P.r.i.n.t.1 C.O.M.1 L.O.C.k E.n.d Notes: C.A.L...
Page 14
EN-12 Ranger™ Count 3000 Series Back Exit...
Page 15
EN-13 Ranger™ Count 3000 Series 4.2 Cal Menu Initial Calibration Procedure: Menu mMeNU C.A.L SpaN --C-- --C-- done Capacity Mass Capacity Mass Note:...
Page 16
EN-14 Ranger™ Count 3000 Series *Bold always represents factory default value. Zero2 [ZErO] Span1 [SpaN] Span2 [SpaN2] Lin1 [LIN] Lin2 [LIN2] GEO [GEO] End Cal [End]...
Page 17
EN-15 Ranger™ Count 3000 Series 4.3 Setup Menu bold auto manual Reset reset Dual Scale [d.scale] Cap2 [CAP2] Grad2 [GrAd2] Power on unit pwWr.UN Zero Range ZErO Auto Opt [A.OPt]...
Page 18
EN-16 Ranger™ Count 3000 Series Auto Tare A.tArE Beeper Opt [bp.OPt] Beeper Signal Bp.sIG Beeper Key BP.key Accumulation aCCUmM End Setup End...
Page 19
EN-17 Ranger™ Count 3000 Series 4.4 Readout Menu bold medium auto Reset reset Stable Range Stable Filter FILtEr AZT AZt Light LIGHt Auto off A.OFF End Readout End...
Page 20
EN-18 Ranger™ Count 3000 Series 4.5 Unit Menu Units...
Page 21
Ranger™ Count 3000 Series EN-19 4.6 Print1 Menu bold Note: Line Reset reset Stable Only Stable Auto Print A.Print Content CONtNt Part Number Note:...
Page 22
EN-20 Ranger™ Count 3000 Series Result Gross Tare Header Note: Footer Note: Mode Unit Info...
Page 23
Ranger™ Count 3000 Series EN-21 Accu Note: Layout layOUt Format Feed Data Transfer data.tr Notes: Print Library P.lib End Print End...
Page 24
EN-22 Ranger™ Count 3000 Series 4.7 COM1 Menu bold 9600 8 none none Note: Reset reset Baud Rate BAUD Parity paritY Stop bit stOP Handshake H.shake...
Page 25
Ranger™ Count 3000 Series EN-23 Alternate command Alt.CmM Print Tare Zero End COM1, End COM2 End 4.8 Lock Menu bold Reset reset Lock Cal l.CAL Lock Setup L.SetuP Lock Read L.read Lock Unit l.Unit...
Page 26
EN-24 Ranger™ Count 3000 Series Lock Print l.print Lock COM l.COmM End Lock End 4.9 End Menu 4.10 Additional Features Note:...