Advertisement
IMPORTANT NOTICE
Please read this user manual carefully before setting up and keep this handy for future reference.
Search "Avantree HT5009" on Youtube for a step-by step video guide. You will find solutions for questions listed below from support.avantree.com or contact technical suppport directly via support@avantree.com.
Scan for FAQ
Support.avantree.com
Check your audio source output options before connecting
If your TV has Optical Out>
NOTE: If you don't know how to change the settings on your TV, or if you cannot hear anything through your earbuds after changing the settings, please contact your TV manufacturer for support.
If your TV has Headphone Out>
Now you can stream audio from your TV.
NOTE: If there is no sound playing from your earbuds or if the LED is still flashing, please set the Sound Out/Speaker setting on your TV to "Wired headphones" or "Headset".
If your TV has Red/White Audio Out (RCA- only for TV)>
Now you can stream audio from your TV.
NOTE: If there is no sound playing from your earbuds or if the LED is still flashing, please set the Sound Out/Speaker setting on your TV to "External Speaker".
If your device is AV Receiver, please use 6.35mm Phone Jack at front>
Slide ATT. Switch to "AVR(-8Db)" when you use the AV Receiver function.
Make sure that the "AUX" LED is on; if not, short press once to select AUX audio. The AUX LED should stay SOLID WHITE when streaming audio.
NOTE:
Please do NOT use the RCA ports on the back of your AV receiver. They will not work and may permanently damage the transmitter.
If your TV is connected to a sound system (e.g. external soundbar, AV receiver, external speaker), our unique "Bypass" feature allows you to connect the Oasis Plus to both the TV and its sound system at the same time. Even if the transmitter turns off, the Bypass feature will still work.
Please make sure that you use the same type of input / output, e.g.
The next time you use the set, please turn the AS9S headphone on first. Once connected, turn on the second headphone. If the Oasis Plus fails to reconnect to the second headphone, you can try to turn on the second headphone before turning on the AS9S. Once they are connected, turn the AS9S on and press on the AS9S once to reconnect.
Please charge the headphone if you hear the "low battery" voice prompt. The RED LED will flash once every 10 seconds. You can charge using a phone charger (5V/500mA-2A output), PC USB port, TV USB port or any other USB outlet using the included USB cable.
It takes about 3.5 hours to fully charge the headphones. The LED will turn RED while charging and turn off once charging is complete. You can use it for almost 40 hours at 60% of the full volume.
Status | LEDs indication |
Transmitter and headset are connected | LED "A" is on for transmitter, LED stay BLUE on headset. |
Transmitter gets valid signal from TV / other audio source | LED "AUX" stay SOLID WHITE if select AUX audio LED "OPT" stay SOLID WHITE if select OPT audio |
Transmitter gets invalid signal from TV / other audio source | LED "AUX"flashes if select AUX audio LED "OPT"flashes if select OPT audio |
Audio input not valid
HT5009 transmitter and headphones fail to reconnect
Reboot both the headphones and the transmitter and give them 5-10 seconds to reconnect. If they don't connect, please follow directions below.
Step 1: Clear the pairing history of the headphones: After turning on, Press and hold both "+" and "-" for 10 seconds until the RED and BLUE LEDs are on SIMULTANEOUSLY for 2 seconds (may look PINK), then release your hands. Now the pairing history of the headphones has been cleared. It will enter pairing mode automatically with the LED flashing RED and BLUE alternately.
Step 2: Set the transmitter into PAIRING MODE - Turn the transmitter on then press and hold for 2 seconds until the "TX" LED will start flashing GREEN and WHITE alternately.
Step 3: Keep the headphones and transmitter close and wait for 5-10 seconds. They should auto-reconnect. Once reconnected, the "A" LED on the transmitter will light up and the LED on the headphones will turn SOLID BLUE.
Step 4: Once the 2 devices are connected, press + on transmitter for 10 seconds, until the "TX" LED turns GREEN for 5 seconds. Now, they are locked.
Any questions? Contact:
Support@avantree.com
(Response Time: 1 working day)
Self-service Support:
Telephone Support (Mon-Fri):
Dispose of the packaging and this product in accordance with the latest provisions. Z-PKQG-5009-BLK-V3
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download Avantree HT5009 - Wireless Headphones And Transmitter Set Manual
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the HT5009 that isn't answered in the manual? Leave your question here.