Table Of Contents - Honeywell ADEMCO VISTA Series Programming Manual

Table of Contents

Recommended Programming Procedure................. 3
Program Field Index ................................................. 4
VISTA-32FB/VISTA-128FB Programming Form...... 5
Partition-Specific Fields .......................................... 10
Programming With #93 Menu Mode....................... 12
Zone Programming................................................. 13
5800 Series Transmitters Loop Designations ........ 16
Expert Mode Zone Programming ........................... 17
Report Code Programming .................................... 21
Alpha Descriptors Programming ............................ 24
Alpha Descriptor Vocabulary.................................. 28
Device Programming .............................................. 29
NOTE: All references in this manual for number of zones, user codes, partitions, VistaKey modules, the master
partition and the event log capacity, use the VISTA-128FB's features. The following table lists the differences between
the VISTA-32FB and the VISTA-128FB control panels. All other features are identical for both panels.
Also, all procedures in this guide for entering zone numbers or user numbers show 3-digit entries, which is valid for
the VISTA-128FB. For the VISTA-32FB these entries are only 2-digit.
Partitions
Number of Zones
Number of User Codes
Master Partition
VistaKey Modules
The purpose of this document is to provide a quick and easy way to program your entire system.
programming procedure is included, followed by a list of program fields with the corresponding program group they belong to
(system-wide, partition-specific, scheduling, etc.). Two program forms are included. One contains all the programming fields,
and the other contains the partition-specific fields. If you are setting up a single-partition system, the partition-specific fields
become system-wide fields.
Following the program forms are system layout worksheets. We recommend that you use these sheets to plan your system
before programming is performed. If you need further information about specific programming options, see the VISTA-
32FB/VISTA-128FB Installation and Setup Guide.
Make sure that one two-line alpha keypad is connected to the control and is set to device address "00."
Single-Partition System
The system default is for a single-partition system.
PROGRAMMING FORM when programming for single-partition usage. Follow the steps outlined in RECOMMENDED
PROGRAMMING PROCEDURE of this document for proper programming procedure.
Multiple-Partition System
You must enter the number of partitions you are using in data field 2*00 to set the system for multiple partitions. Use the
VISTA-32FB/VISTA-128FB SINGLE PARTITION and the PARTITION-SPECIFIC PROGRAM FORMS when programming
the system for multiple partitions. Follow the steps outlined in RECOMMENDED PROGRAMMING PROCEDURE of this
document for proper programming procedure.
• To enter program mode, enter installer code + [8] + [0] + [0] + [0]. For the VISTA-32FB installer code + [8] + [0] + [0].
To set standard defaults, press ✱97
•
To change to next page of program fields, press ✱94
•
To return to previous set of fields, press ✱99
•
• To erase account and phone number field entries, press [✱] + field number + [✱]
• To assign zone descriptors, press #93 + follow menu prompts
• To add custom words, press #93 + follow menu prompts
• To enter Installer's Message, press #93 + follow menu prompts
To exit program mode, enter ✱99 OR ✱98: ✱99 allows re-access to programming mode by installer code.
•
✱98 prevents re-access to programming mode by installer code.
Standard default (✱97) values are shown in brackets [ ], otherwise default = 0.
Feature
SUMMARY OF PROGRAMMING COMMANDS
Output Programming .............................................. 32
Relay Voice Descriptors ......................................... 36
Relay Voice Descriptors and Custom Word
Substitutes Vocabulary........................................ 37
Custom Word Substitutes for VIP Module
Annunciation........................................................ 37
System Layout Worksheets.................................... 38
Output Devices Worksheets ................................... 50
Scheduling Menu Prompts ..................................... 56
Scheduling Worksheets .......................................... 57
VISTA-32FB Summary of Connections Diagram ... 62
VISTA-128FB Summary of Connections Diagram . 63
VISTA-32FB
2
32
75
3
4
Use the VISTA-32FB/VISTA-128FB SINGLE PARTITION
-2-
VISTA-128FB
8
128
150
9
8
A recommended