Issue Nov. 2014 Rev. Model No: ES15V-Q1(R) GENERAL SAFETY Your safety and the safety of others is extremely important. We have provided many important safety messages in this manual and on the appliance. Always read and obey all safety messages. This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Issue Nov. 2014 Rev. Model No: ES15V-Q1(R) 1.Product Information 1.1 Features Safety: High-quality heat proof stainless steel electric heating element, over-temperature protection; overpressure protection of tank; safe and reliable. “Safe Care” patented design together with the function of monitoring and displaying of live ground wire has become a real safeguard for family safety.
Issue Nov. 2014 Rev. Model No: ES15V-Q1(R) 1.4 Specifications Model No. ES15V-Q1(R) Rated voltage (V) AC 220-240 Rated frequency (Hz) Rated temperature ( ) ℃ Rated Power (W) 2000 Capacity (L) Rated pressure (MPa) 0.80 Installation method Vertical Control method Mechanical Tap water pressure 0.05MPa~0.75MPa Waterproof grade...
Issue Nov. 2014 Rev. Model No: ES15V-Q1(R) 2.Installation 2.1 General requirements The wall for installation shall be solid and reliable which can bear more 4 times of weight of the heater with full of water. The installation position shall be with a floor drain and can facilitate for use and maintenance.
Page 8
Issue Nov. 2014 Rev. Model No: ES15V-Q1(R) Cold water supply It is important to ensure that the cold water main is capable of supplying the increased demand. A minimum pressure of approximately 0.05MPa (0.5 bar ) is required for satisfactory operation. NOTE: THE MAINS WATER SUPPLY MUST NOT EXCEED 0.75MPa (7.5 BAR).
Issue Nov. 2014 Rev. Model No: ES15V-Q1(R) 2.2 Installation Method The water heater must be installed by the installation professionals from our after-sale service department or its designated personnel. The wall-hung type installation shall be adopted for the water heater. As shown in Fig.1, drill four holes of 12 mm in diameter and 65 mm in depth in the wall by a percussion drill, insert and fix expansion hooks and expansion bolts into the corresponding holes, and then raise the water heater, put the wall-mount rack on the hooks and bolts;...
Issue Nov. 2014 Rev. Model No: ES15V-Q1(R) 3.Servicing Procedures 3.1 Remove the shell. Before maintenance, the shell should be removed. Firstly, take off the red and blue rings; then remove four screws, after that the shell can be removed, Attention to the snap joint, Don’t break them. ...
Issue Nov. 2014 Rev. Model No: ES15V-Q1(R) High Temperature Thermostat 3. Label the wires and connections so that 4. Remove the high temperature thermostat you can properly reconnect them later from the claw on back cover, and do the ...
Issue Nov. 2014 Rev. Model No: ES15V-Q1(R) 4 Wiring diagram 5.Trouble shooting Problems Matters to be confirmed Solutions Whether there is no water or too low Check it pressure in the water system? No flow Whether water-use spot is blocked, or Check and clean it hot water valve is open or not? ①...
Page 14
Issue Nov. 2014 Rev. Model No: ES15V-Q1(R) cold water not? ②Whether water temperature is Adjust according to the instructions properly adjusted? in the Manual. ③Whether the heating time is too short Adjust according to the instructions for setting temperature needed? in the Manual. If it is confirmed that the problem is ④Whether components are damaged beyond above ①,②or③, please...
Page 15
Issue Nov. 2014 Rev. Model No: ES15V-Q1(R) Sincere Forever Haier Group Haier Industrial Park, No.1, Haier Road 266101, Qingdao, China http://www.haier.com Printed in China 15 ...