Table of Contents
Advertisement
Playing Bluetooth® Audio
You can set up the STAGEPAS 200BTR/200 so it will play audio files stored in Bluetooth devices, such as a mobile
device.
Registering (pairing) a
Bluetooth® device
Before you can connect a Bluetooth device for the first time,
you need to "pair" the device. "Pairing" refers to registering
one Bluetooth device with another Bluetooth device.
Once pairing is complete, you will be able to reconnect those
devices easily after you terminate a Bluetooth connection.
1
Make sure that the
indicator is turned off. If it is lit steadily or
is flashing, press the [
switch to set the Bluetooth function to
standby mode.
2
Press and hold down the
switch for three seconds or longer.
The [
] (Bluetooth) indicator will flash rapidly,
indicating that the unit is ready for pairing.
3
Turn on the Bluetooth function on the
Bluetooth device that you want to
connect.
For more information, refer to the owner's manual for
the Bluetooth device.
4
Once the Bluetooth device displays a list of
other Bluetooth devices that are available
for connection, select STAGEPAS 200
AUDIO.
NOTE
You can change the name of the unit in the Device Name
setting of STAGEPAS Controller.
When the pairing process is complete, the Bluetooth
connection is established and the [
indicator lights up.
NOTE
• The STAGEPAS 200BTR/200 enables you to pair (register) up to
eight Bluetooth devices. However, only one such device can
establish the connection. Once the ninth Bluetooth device has
been paired successfully, the pairing information for the Bluetooth
device that was connected earliest will be deleted.
• You must complete the pairing process on the Bluetooth device
within two minutes.
20
STAGEPAS 200BTR STAGEPAS 200 Owner's Manual
(Bluetooth)
[
]
(Bluetooth)
]
(Bluetooth)
[
]
] (Bluetooth)
Connecting a Bluetooth® device
Connecting from the STAGEPAS 200BTR/200
1
Press and hold down the
switch for one second.
The [
] (Bluetooth) indicator flashes slowly, and the
unit starts searching for a registered Bluetooth device.
2
Turn on the Bluetooth function on the
Bluetooth device that you want to connect.
When the connection is made automatically, the [
(Bluetooth) indicator lights up.
Connecting from a Bluetooth device
Even if Bluetooth on the unit is in standby mode, you can still
use your Bluetooth device to connect it by following the
procedure below.
1
Turn on the Bluetooth function on the
Bluetooth device that you want to connect.
2
Select STAGEPAS 200 AUDIO from the list of
Bluetooth devices displayed on your
Bluetooth device.
Playing audio files stored on a
Bluetooth® device
You can use the STAGEPAS 200BTR/200 to listen to an audio
file playing on your Bluetooth device.
Signals from the Bluetooth device are input to channel 4/5.
We recommend that you set the volume on the Bluetooth
device a little higher than normal, and then adjust the
volume for channel 4/5 using the channel [LEVEL] control.
If you receive a call or text message while playing audio files
on your Bluetooth device such as a smartphone, audio file
playback might be paused momentarily.
To avoid this interruption, enable Airplane Mode, and then
set Bluetooth to ON on your Bluetooth device.
Disconnecting the Bluetooth® device
To disconnect the Bluetooth device, do one of the following:
• Use the Bluetooth device to disconnect. (The [
(Bluetooth) indicator on the unit turns off ).
• Press the [
] (Bluetooth) switch on the unit to engage
Bluetooth standby mode. (The [
turns off.)
NOTICE
Before you turn off the power to the unit, make sure that the
Bluetooth function is turned off. (The [
should be off.) If you turn off the power to the unit while the
Bluetooth function remains enabled, the unit might lose the pairing
information.
(Bluetooth)
[
]
]
]
] (Bluetooth) indicator
] (Bluetooth) indicator
Advertisement
Table of Contents
