Chicco FULLY Manual page 51

MAINTENANCE
If necessary, lubricate the moving parts with dry silicone
lubricant. Regularly check the condition of the wheels and
clean off all dust and sand. To avoid friction that may com-
promise the correct functioning of the stroller, make sure
that all plastic parts that slide on the metal tubes are free of
dust, dirt and sand. Keep the stroller in a dry place.
The Fully stroller, with the use of specific adaptors, can be
used with two seats, with the possibility of transforming
them into wheelchairs or, possibly, in combination with the
KeyFit child car sear.
USING ADAPTORS "2" – "3" FOR FITTING THE SECOND SEAT
Before fitting the seat, the relevant adaptors are to be fas-
tened to the frame.
1. The adaptors have numbers to identify the pair of adapt-
ers and symbols to guide correct installation on the
frame (Fig. 1- 1A).
2. The same symbols are repeated on the front and rear
legs of the frame as on the adaptors. The pair of adaptors
identified with "2" can only be used on the front legs of
the stroller (Fig.2 - 2A), while the adaptors "3" can only be
used on the rear legs (Fig. 2B - 2C).
After installing the adaptors needed to create the chosen
configuration, you can install the second seat on the frame.
To fasten the adaptors on the frame, it is necessary to open
them, lay one of the two parts on the tube and close the
second side on the first one, until you hear a click.
WARNING: Correct fastening requires that the adaptors
adhere well to the plastic component of the wheel assem-
bly, either at the rear or at the front, depending on the cho-
sen configuration.
FITTING THE SECOND SEAT: STROLLER CONFIGURATION
WARNING: The second Fully seat fits only in adaptors "2"
and "3" supplied.
3. To fit the seat on the stroller, open it acting on it (Fig. 3 –
3A) until you hear the locking click (Fig. 3B).
4. Fasten the buckle A, placed externally in the area of the
seat near the child's feet (Fig. 4); Then fasten buckles B,
located under the seat (Fig. 4A).
5. To attach the seat, introduce the two hooks in the adap-
tors until you hear a locking click. When fitting on the
front legs with adaptors "2", the seat can only be mounted
parent-facing (Fig.5). If you wish to position the seat on
the rear legs, using the adaptors "3", it can only be fitted
forward facing (Fig.5A).
WARNING: Make sure the seat is installed properly by pulling
it upwards.
WARNING: The second seat on adapters "2" and "3" (parent
facing and/or forward facing) must only be used with the
first seat installed. It is not possible to use the Fully stroller
with the second seat only.
6. To remove the seat from the frame, press the side buttons
and pull upward (fig. 6). These operations must not be
performed when the child is inside the seat.
WARNING: Do not remove the seat from the stroller when
the child is inside it.
HOODS
The seat features an extendable hood.
7. To adjust the hood (in three positions) push it forward as
far as it goes (Fig. 7). To increase the extension, open the
zipper (Fig. 7A) and then push forward.
To close the hood, act on the button on the central part of the
handle and push it towards the backrest (Fig. 7B).
8. To remove the hood, open the zipper near the tube of
the backrest completely and press the buttons located
outside on the hood's joints; then pull the hood upwards
(Fig. 8).
To fasten the hood, follow the steps described above in re-
verse order.
WARNING: The canopy must be fixed to both sides of the
stroller. Ensure that the canopy is correctly fastened.
ADJUSTING THE SECOND SEAT
Once the seat is fitted on the frame, it can be reclined in
three different positions.
9. The entire seat can be adjusted by pressing simultaneously
the buttons located above the central articulated joint (fig.
9).
10. The angle of the backrest can be modified compared to
the seat by acting on the adjuster located behind the
backrest (Fig. 10).
11. It is possible to adjust the leg rest in various positions, by
pressing simultaneously the side buttons (Fig. 11).
12. The seat features a detachable bumper bar. To remove it,
press the buttons located on the sides (Fig. 12).
To position and remove the child, unhook the bar from one
side only (Fig. 12A).
WARNING: Always fasten the safety harnesses. The BUMP-
ER bar IS NOT a device for containing your child.
WARNING: The bumper bar must not be used to lift the
stroller with the child inside of it.
HOW TO USE THE SAFETY HARNESS
The seat seat is equipped with a retaining system with five
anchoring points, consisting of two shoulder straps, two
adjusting holes, a waist belt and a crotch strap with buckle,
already assembled.
13. WARNING: To adapt the belts to the body of the child,
use the shoulder straps, passing them through the two
regulation holes (Fig. 13).
After placing the child in the seat, fasten the belts by thread-
ing first the two forks inside the shoulder straps' slot (fig. 13A)
and then introduce them inside the crotch strap buckle (fig.
13B); adjust the length of the straps, ensuring that they ad-
here to the child's shoulders and body correctly.
14. To unfasten the waist belt, press and pull the lateral
prong (Fig. 14).
15. The waist belt must always be passed through the 2
D-shaped rings on the sides of the stroller seat (fig. 15).
WARNING: Always use the restraint systems. For the safety
of your child use all five fixing points of the safety harness
belts.
REMOVING THE SAFETY BELTS
The safety belts can be removed (to be washed or used in
pram/semi-rigid carrycot configuration).
To remove the belts, unfasten the waist belt from the rela-
tive "D''-shaped rings and the shoulder straps from the fab-
ric slots located on the backrest. After removing the safety
belts, make sure that the belts are re-assembled properly
using the anchoring points.
WARNING: Once the safety belts are removed, keep them
23