Page 1
24/10/2022, 09:59 UVC-G3-FLEX Quick Start Guide UVC-G3-FLEX Quick Start Guide Package Contents Camera Flush Mount Pole/Wall Mount Outdoor Cover Security Screw (Qty. 1) Screws (Qty. 3) Screw Anchors (Qty. 3) Zip Ties (Qty. 2) Installation Requirements Phillips screwdriver Drill and 6 mm (1/4") bit for drywall anchors and 3 mm (1/8") for screws)
Surge protection should be used for all outdoor installations. We recommend that you use two Ethernet Surge Protectors, model ETH-SP-G2, one near the UVC-G3-Flex and the other at the entry point to the building. The ETH-SP-G2 will absorb power surges and safely discharge them into the ground.
24/10/2022, 09:59 UVC-G3-FLEX Quick Start Guide Hardware Overview UVC-G3-FLEX Quick Start Guide Device is busy; do not touch or unplug it. This Alternating White/Blue usually indicates that a process such as a firmware upgrade is taking place. Connected to UniFi Protect Controller; Reset...
24/10/2022, 09:59 UVC-G3-FLEX Quick Start Guide Bottom View UVC-G3-FLEX Quick Start Guide Ethernet Port The Ethernet Port is a 10/100 Mbps port used to supply power from a PoE 802.3af-compliant switch to the camera. The switch should be connected to a LAN running DHCP services and the UniFi Protect Controller software.
Page 5
24/10/2022, 09:59 UVC-G3-FLEX Quick Start Guide surface outdoors. The Outdoor Cover is not required UVC-G3-FLEX Quick Start Guide for indoor installations. Use the Pole Mount with two plastic zip ties and the Outdoor Cover to install the G3 Flex camera on an outdoor pole.
24/10/2022, 09:59 UVC-G3-FLEX Quick Start Guide Installation UVC-G3-FLEX Quick Start Guide The UVC G3 Flex can be installed using one of the following methods: Desktop For installing on a flat surface such as a desktop or table/shelf; could be set up for temporary installations.
Page 7
24/10/2022, 09:59 UVC-G3-FLEX Quick Start Guide UVC-G3-FLEX Quick Start Guide 3. Attach the camera to the Flush Mount by lining up the notches with the slots in the base of the camera. Press firmly together until the camera is secure.
Page 8
24/10/2022, 09:59 UVC-G3-FLEX Quick Start Guide UVC-G3-FLEX Quick Start Guide Installation complete. Desktop / Table Install Wall/Ceiling 1. If the Ethernet cable is coming from the inside of a wall: a. Drill or cut a hole in the wall and feed the Ethernet cable through the opening.
Page 9
24/10/2022, 09:59 UVC-G3-FLEX Quick Start Guide UVC-G3-FLEX Quick Start Guide Top Side Down Mounting Vertical Upright Mounting 3. Connect the Ethernet cable to the Ethernet Port in the base of the camera. 4. Attach the camera to the Flush Mount by lining up the notches with the slots in the base of the camera.
Page 10
24/10/2022, 09:59 UVC-G3-FLEX Quick Start Guide UVC-G3-FLEX Quick Start Guide Vertical mounting on ceiling Vertical mounting on a wall Installation complete. Horizozntal Surface / Ceiling with Flush Mount https://dl.ui.com/qsg/UVC-G3-FLEX/UVC-G3-FLEX_EN.html 10/18...
Page 11
24/10/2022, 09:59 UVC-G3-FLEX Quick Start Guide UVC-G3-FLEX Quick Start Guide Indoor Wall with Flush Mount Pole Note: If you are mounting the camera outdoors, it must be installed in the upright position to prevent water from getting into the base of the camera.
Page 12
24/10/2022, 09:59 UVC-G3-FLEX Quick Start Guide UVC-G3-FLEX Quick Start Guide Note: When using the Outdoor Cover, use an Ethernet cable without strain-relief boots on the connector. This will prevent unnecessary tension on the cable ends. 3. Connect the Ethernet cable to the Ethernet Port on the G3 Flex camera.
Page 13
24/10/2022, 09:59 UVC-G3-FLEX Quick Start Guide UVC-G3-FLEX Quick Start Guide 5. Attach the camera to the Pole Mount: a. Press the camera against the Pole Mount and line up the notches on the mount with the slots on the bottom of the camera.
Page 14
24/10/2022, 09:59 UVC-G3-FLEX Quick Start Guide 6. Use a phillips screwdriver to install the Security Screw through the Outdoor UVC-G3-FLEX Quick Start Guide Cover and into the base of the camera. This helps secrure the camera to the mount. 7. Adjust the camera to the desired viewing angle by:...
UVC-G3-FLEX Quick Start Guide Pole Mount Install Setting Up UniFi Protect via App Download and install the UniFi Protect Mobile App to configure the UVC-G3-Flex. Note: When you first launch UniFi Protect, the app will prompt you to enable Bluetooth and other relevant features necessary to provide the best user experience possible.
24/10/2022, 09:59 UVC-G3-FLEX Quick Start Guide Limited Warranty UVC-G3-FLEX Quick Start Guide ui.com/support/warranty The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and, where applicable, specify arbitration instead of jury trials or class actions.