Related Manuals for Pilz PSS u2 ES 8PTD 24V 0V
Summary of Contents for Pilz PSS u2 ES 8PTD 24V 0V
- Page 1 PSS u2 ES 8PTD 24V 0V Control system PSS u2 Remote I/O system PSS u2 Operating Manual-1003768-EN-03...
- Page 2 We do assure you that all persons are regarded without discrim- ination and on an equal basis. All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made for the user's internal purposes. Suggestions and comments for improving this documenta- tion will be gratefully received.
-
Page 3: Table Of Contents
General wiring guidelines ......................6.1.1 Connection mechanism for terminal blocks ................Terminal configuration ......................Operation ..........................Display elements and messages ....................Technical details ........................Order reference ........................Product ............................. Accessories ..........................Operating Manual PSS u2 ES 8PTD 24V 0V 1003768-EN-03... -
Page 4: Introduction
This operating manual explains the function and operation, describes the installation and provides guidelines on how to connect the product. This documentation is valid for the product PSS u2 ES 8PTD 24V 0V hardware version 01 or higher. It is valid until new documentation is published. - Page 5 Introduction INFORMATION This gives advice on applications and provides information on special fea- tures. Operating Manual PSS u2 ES 8PTD 24V 0V 1003768-EN-03...
-
Page 6: Overview
Details of the terminal blocks that can be used are available under "Intended Use". Module features Application of the product PSS u2 ES 8PTD 24V 0V: Electronic module with voltage outputs and terminals for tapping the 0 V periphery supply for standard applications. -
Page 7: Safety
Any use of the module that is not in accordance with the technical details. Please also refer to Installation manual PSS u2. The module PSS u2 ES 8PTD 24V 0V may be used in conjunction with the following ter- minal block: 16-pin terminal block System requirements... -
Page 8: Safety Regulations
Any type of modification has been made (e.g. exchanging components on the PCB boards, soldering work etc.). 3.3.3 Disposal When decommissioning, please comply with local regulations regarding the disposal of electronic devices (e.g. Electrical and Electronic Equipment Act). Operating Manual PSS u2 ES 8PTD 24V 0V 1003768-EN-03... -
Page 9: Function Description
Supply Supply Supply +24 V DC Fig.: Block diagram PSS u2 ES 8PTD 24V 0V Supply The module is supplied with voltage via the head module. The periphery supply provides the voltage outputs with voltage When the supply voltage for the periphery supply is interrupted, the periphery supply is buf- fered for 20 ms. -
Page 10: Energy-Saving Functions
– The module switches off the voltage at the voltage outputs. Standby mode – All module functions are inactive. – The LEDs for displaying the module and terminal status are switched off. Operating Manual PSS u2 ES 8PTD 24V 0V | 10 1003768-EN-03... -
Page 11: Installation
5.1.1 Dimensions The dimensions include the backplane, electronic module and terminal block. 12,5 51,1 111,1 Fig.: Dimensions in mm, including backplane, electronic module and terminal block Operating Manual PSS u2 ES 8PTD 24V 0V | 11 1003768-EN-03... -
Page 12: Inserting And Removing An Electronic Module
Inserting an electronic module 1. Insert the electronic module into the suspen- sion lug on the back- plane. 2. Swivel the electronic module downwards until you hear it click into place. Operating Manual PSS u2 ES 8PTD 24V 0V | 12 1003768-EN-03... - Page 13 Installation 3. Insert the terminal block into the suspen- sion lug on the module. 4. Swivel the terminal block upwards until you hear it click into place. Operating Manual PSS u2 ES 8PTD 24V 0V | 13 1003768-EN-03...
-
Page 14: Removing An Electronic Module
2. Press the unlocking mechanism that is shown by the arrow and pull off the electronic module upwards. Operating Manual PSS u2 ES 8PTD 24V 0V | 14 1003768-EN-03... -
Page 15: Changing An Electronic Module During Operation
– Restart of the head module. After a restart, the system behaves as after a warm reset using a reset pushbutton (see operating manual of the head module, chapter “Reset pusbutton", section "Carrying out a warm reset (restart)"). Operating Manual PSS u2 ES 8PTD 24V 0V | 15 1003768-EN-03... -
Page 16: Wiring
Strip the wire back 9 mm. Feed the stripped cable as far as it will go into the opening for the spring-loaded terminal. Check that the cable is firmly seated. Operating Manual PSS u2 ES 8PTD 24V 0V | 16 1003768-EN-03... -
Page 17: Terminal Configuration
12: 0 V 13: Output O12 13: Voltage output S6 14: Output O13 14 0 V 15: Output O14 15: Voltage output S7 16: Output O15 16: 0 V Operating Manual PSS u2 ES 8PTD 24V 0V | 17 1003768-EN-03... -
Page 18: Operation
[1] Module status display [2] Terminal status display The terminal status display [2] is only active for the 24 V terminals (terminal 1, 3, 5, 7, 9, 13 and 15). Operating Manual PSS u2 ES 8PTD 24V 0V | 18 1003768-EN-03... - Page 19 – the voltage outputs are switched off After the "too hot" message has been received, if the temperature drops back below the "too warm" threshold value, the module will switch to an error-free state. Operating Manual PSS u2 ES 8PTD 24V 0V | 19 1003768-EN-03...
-
Page 20: Technical Details
In accordance with the standard EN 60068-2-6 Frequency 8,4 - 150 Hz Acceleration 10 m/s² Shock stress In accordance with the standard EN 60068-2-27 Acceleration 150 m/s² Duration 11 ms Operating Manual PSS u2 ES 8PTD 24V 0V | 20 1003768-EN-03... - Page 21 Mechanical data Material Housing Mounting type plug-in Dimensions Height 110,8 mm Width 12,5 mm Depth 72,5 mm Weight 33 g Where standards are undated, the 2015-04 latest editions shall apply. Operating Manual PSS u2 ES 8PTD 24V 0V | 21 1003768-EN-03...
-
Page 22: Order Reference
Label holder for terminal block 328912 (10 pcs.) 61 x 11.5 mm, scope of supply: 10 pieces Codierelemente Produkttyp Merkmale Bestell-Nr. PSS u2 A CE E (10 pc.) Codierelemente für Elektronikmodule, 10 328860 Stück Operating Manual PSS u2 ES 8PTD 24V 0V | 22 1003768-EN-03... - Page 23 Order reference Backplanes Product type Features Order no. PSS u2 B 1 Backplane, 1 slot 328811 PSS u2 B 4 Backplane, 4 slots 328810 Operating Manual PSS u2 ES 8PTD 24V 0V | 23 1003768-EN-03...
- Page 24 We are represented internationally. Please refer to our homepage www.pilz.com for further details or contact our headquarters. Headquarters: Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany Telephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: info@pilz.com, Internet: www.pilz.com...
Need help?
Do you have a question about the PSS u2 ES 8PTD 24V 0V and is the answer not in the manual?
Questions and answers