Table of Contents
Advertisement
Quick Links
Greenfire GF55-2 Freestanding Pellet Stove
Model
Heat Output BTUs
Emissions (grams/hr) EPA Certified
Efficiency (EPA HHV)*/**
24"
Efficiency (EPA LHV)
(610mm)
Flue Size
US Biomass Tax Rebate Eligible**
*US Biomass Tax Rebate eligibility is based on the HHV value being
greater than or equal to 75%.
** When using optional top vent adaptor kit (GF55-920) and 3'' to 6''
flue adaptor (3PVP-X6). See instruction manual for further information.
GF55-2 DIMENSIONS
1
9
/
"
16
(40mm)
19
/
"
7
16
(494mm)
13
1
/
"
16
(332mm)
1
5
/
"
8
(41mm)
14
5
/
"
8
(356mm)
14
5
/
"
8
(371mm)
7
11
/
"
16
(291mm)
GF55-2
7,751-32,739 BTUs
1.8 gram/hr
75%
81.9%
3" (76mm)
Yes
23
/
"
1
16
(586mm)
34
(866mm)
24
/
"
7
16
(620mm)
23
1
/
"
16
(586mm)
5
3
/
"
4
(146mm)
20
5
/
"
16
(508mm)
6
11
/
"
16
1"
(170mm)
(25mm)
1" (25mm)
1
/
"
8
3"
(76mm)
20
/
"
5
16
(516mm)
12
9
/
16
(319mm)
5
11
/
" (145mm)
16
24"
(610mm)
"
GF55-2 Pellet Stove |
19
1
/
"
8
(866mm)
1
Advertisement
Table of Contents
Related Manuals for Regency Greenfire GF55-2
Summary of Contents for Regency Greenfire GF55-2
- Page 1 Greenfire GF55-2 Freestanding Pellet Stove Model GF55-2 Heat Output BTUs 7,751-32,739 BTUs Emissions (grams/hr) EPA Certified 1.8 gram/hr Efficiency (EPA HHV)*/** 24" Efficiency (EPA LHV) 81.9% (610mm) Flue Size 3" (76mm) US Biomass Tax Rebate Eligible** *US Biomass Tax Rebate eligibility is based on the HHV value being greater than or equal to 75%.
-
Page 2: Clearances To Combustibles
CLEARANCES CLEARANCES TO COMBUSTIBLES ALCOVE CLEARANCES These dimensions are minimum clearances to combustibles, however it is highly recommended that you leave sufficient room on each side (20" where possible) for servicing, routine cleaning and maintenance. Minimum Width 36" (914mm) This pellet stove requires floor protection. The floor protection must be non-combustible, extending 6"... -
Page 3: Vent Termination Requirements
VENT TERMINATION REQUIREMENTS Minimum Clearance Letter Description 24 in (61cm) Above grass, top of plants, wood, or any other combustible materials. 48 in (122cm) From beside/below any door or window that may be opened. (18" [46cm] if outside fresh air installed). 12 in (30cm) From above any door or window that may be opened. -
Page 4: Corner Through Wall Installation
EXHAUST AND FRESH AIR INTAKE LOCATION Outside Fresh Air Connection: Outside fresh air is mandatory when installing this unit in EXHAUST: airtight homes and mobile homes. Base of unit to center of flue 20-5/16" (508mm) A Fresh-air intake is strongly recommended for all installations. Failure to install intake air may result in improper combustion as well Side of unit to center of flue 6-11/16"... -
Page 5: Horizontal Exhaust Through Wall Installation
HORIZONTAL EXHAUST THROUGH WALL INSTALLATION Vent installation: install vent at clearances specified by the vent manufacturer. A chimney connector shall not pass through an attic or roof space, closet or similar concealed spaces, or a floor, or ceiling. Where passage through Exhaust Tube a wall or partition of combustible construction is desired, the installation 3"... -
Page 6: Inside Vertical Installations
VERTICAL RISE WITH HORIZONTAL INSIDE VERTICAL INSTALLATIONS TERMINATION INSTALLATION 1. Choose a stove location that is ideal. Refer to "Locating Your Pellet A 45° elbow may be used in place of the termination cap (or stainless Appliance" section. steel termination hood). 2. -
Page 7: Hearth Mount Installation
Steel Plate or Flashing Flexible or Rigid 6" Stainless Steel Liner HEARTH MOUNT INSTALLATION Refer to Figures on the left: Damper Removed 1. Install the hearth pad. or Fastened Open 2. Lock the fireplace damper in the open position. 10" (25.4 cm) Mantel 3. - Page 8 TOP VENT ADAPTOR KIT & 3” (76 MM) TO 6” (152 MM) FLUE ADAPTOR (APPROVED TOP VENT ADAPTOR KIT & 3” (76 MM) TO 6” (152 MM) FLUE ADAPTOR (APPROVED FOR FOR VERTICAL INSTALLATIONS ONLY) VERTICAL INSTALLATIONS ONLY) 3PVP-X6 3” (76mm) pipe lengths to class A chimney GF55-920 *In order to achieve the maximum rated efficiency of 75% HHV purchase of a top vent adaptor kit (GF55-920) is required.