Table of Contents
Advertisement
Owners &
Installation
LISTINGS AND CODE APPROVALS
These gas appliances have been tested in
accordance with AS4553-2000, NZS 5262
and have been certifi ed by the Australian Gas
Association for installation and operation as
described in these Installation and Operating
Instructions.
Your unit should be serviced annually by
an authorised service person.
Freestanding Gas Stove
PLEASE KEEP THESE INSTRUCTIONS
FOR FUTURE REFERENCE
WARNING:
Improper installation, adjustment, altera-
tion, service or maintenance can cause
injury or property damage. Refer to this
manual. For assistance or additional in-
formation consult an authorized installer,
service agency or the gas supplier.
FOR YOUR SAFETY
Do not store or use gasoline or other fl am-
mable vapours and liquids in the vicinity of
this or any other appliance.
Installation and service must be performed
by an authorized installer, service agency or
the gas supplier.
918-534
Models: F38-NG2
F38-LPG2
FOR YOUR SAFETY
What to do if you smell gas:
Do not try to light any appli-
ance
Do not touch any electri-
cal switch: do not use any
phone in your building.
Immediately call your gas
supplier from a neighbour's
phone. Follow the gas sup-
plier's instructions.
If you cannot reach your
gas supplier, call the fi re
department.
07/18/07
Advertisement
Table of Contents
Related Manuals for Regency F38-NG2
Summary of Contents for Regency F38-NG2
- Page 1 Installation and service must be performed by an authorized installer, service agency or the gas supplier. 918-534 Models: F38-NG2 F38-LPG2 FOR YOUR SAFETY What to do if you smell gas: Do not try to light any appli-...
- Page 2 fl ick of a switch. The models F38-NG2, and F38-LPG2 of this series has been approved by AGA for both safety and effi ciency. As it also bears our own mark, it promises to provide you with economy, comfort and security for many trouble free years to follow.
-
Page 3: Table Of Contents
SAFETY LABEL Safety Label ...5 INSTALLATION General Information ...5 Important ...5 Before You Start ...5 General Safety Information ...5 Clearances to Combustibles ...6 Draft Diverter ...6 Flueing ...6 Installation Checklist ...6 Gas Connection ...7 Gas Pipe Pressure Testing ...7 Conversion Kit# 731-968 from NG to LPG ...8 Aeration Adjustment ...9 Log Set Installation ...9 Front Door Installation ... -
Page 4: Safety Label
SAFETY LABEL This is a copy of the label that accompanies each Freestanding Gas Stove. We have printed a copy of the contents here for your review. The safety label is located on the inside of the drop down pedestal door. -
Page 5: Installation
Regency F38-2 Freestanding Gas Heater IMPORTANT The F38-2 Freestanding Gas Stove must be installed in accordance with these instructions. Carefully read all the instructions in this manual fi rst. Consult the "authority having jurisdiction" to determine the need for a permit prior to starting the installation. -
Page 6: Clearances To Combustibles
Use the minimum clearances shown in the diagrams below for all installations. F38-NG2 & F38-LPG2 Clearances A Side Wall to Unit 7-1/2" / 190 mm B Back Wall to Unit 6" / 155 mm E Side Wall to Unit 2"... -
Page 7: Gas Connection
11) Alternative TC Connection Point 12) Thermoelectric Unit 13) Additional Valve Mounting Hole INSTALLATION System Data F38-2 F38-NG2: For 0 to 610 meters altitude F38-LPG2: For 0 to 610 meters altitude Burner Inlet Orifi ce Sizes: Burner Max. Input 38 mj 31 mj Min. -
Page 8: Conversion Kit# 731-968 From Ng To Lpg
19) Reverse steps 3) to 2). 20) Attach the label "This unit has been con- verted to LPG" near or on top of the Serial # decal. 21) Replace yellow "NG" label with red "LPG" label. Regency F38-2 Freestanding Gas Stove... -
Page 9: Aeration Adjustment
ADJUSTMENT The burner aeration is factory set but may need adjusting due to either the local gas supply or altitude. F38-2 with 38 mj F38-NG2 Full open F38-LPG2 LPG: 6.4 mm open Caution: Carbon will be produced if the air shutter is closed too much. - Page 10 11) Test fi re to ensure proper light off (make sure fl ame fl ows smoothly from one end of burner to the other. If there is any fl ame hesitation, check that area for any blockage of the burner port. A)02-65 E)02-45 Regency F38-2 Freestanding Gas Stove...
-
Page 11: Front Door Installation
3) Close the door. The latch plate must be centered around the alignment pin. See diagram 2. If the latch plate interferes with the corner of the stove you may want to angle the plate slightly so the door closes easier. -
Page 12: Optional Wall Thermostat
First allow the unit to burn for 15 min. to stabilize. 3) Check for proper draft. CAUTION Any alteration to the product that causes sooting or carboning that results in damage to the exterior facia is not the responsibility of the Regency F38-2 Freestanding Gas Stove... -
Page 13: Wiring
No electrical power supply is required for the gas control to operate. However, a 240V A.C. power supply is needed for the fan/blower operation. Caution: Ensure that the wires do not touch any hot surfaces and are away from sharp edges. Regency F38-2 Freestanding Gas Heater WIRING WARNING: Electrical Grounding... -
Page 14: Operating Instructions
Set the fan speed on control panel at the top rear of the unit to adjust to the desired speed. The fan will turn on as the stove comes up to operating temperature. After the unit has been turned off and the unit cooled... -
Page 15: Copy Of The Lighting Plate Instructions
OPERATING INSTRUCTIONS COPY OF THE LIGHTING PLATE INSTRUCTIONS Gas Inlet WARNING: DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IN OPERATION. Regency F38-2 Freestanding Gas Heater... -
Page 16: Pilot Adjustment
Unit Body/Firebox: Different types and thicknesses of steel will expand and contract at different rates resulting in some "cracking" and "ticking" sounds will be heard throughout the cycling process. Regency F38-2 Freestanding Gas Stove... -
Page 17: Maintenance
MAINTENANCE INSTRUCTIONS 1) Always shut the valve off before cleaning. For relighting, refer to lighting instructions. Keep the burner and control compartment clean by brushing and vacuuming at least once a year. When cleaning the logs, use a soft clean brush as the logs are fragile and easily damaged. -
Page 18: Fan Maintenance
WARNING: Electrical Grounding In- structions This appliance is equipped with a three pronged (grounding) plug... -
Page 19: Removing Valve
If your valve requires maintenance or replace- ment, follow these instructions: NOTE: Always shut off the gas supply before removing the valve. 1) Open front pedestal door and unhook chain. You may want to put a soft cloth on the base of the unit so that when the pedestal door is open it doesn't scratch the paint. -
Page 20: Parts List
*Not available as a replacement part. Mounting Bracket - Fan Thermodisc Thermodisc Cover Rear Panel Firebox Baffl e False Top Assembly Ult. 6" Flue Collar (Optional) Rear Control Panel Conversion Kit - to LPG Logo Plate Manual Regency F38-2 Freestanding Gas Stove... -
Page 21: F38-2 Burner & Log Assembly
F38-2 BURNER & LOG ASSEMBLY Part # Description 52) 910-190 Piezo Ignitor & Nut 54) 910-373 Knob - S.I.T. Valve Extension 55) 910-372 Flame Adjusting Knob 56) 918-088 Control Panel Decal 57) * Control Panel Plate 750-527/P Valve Assembly - NG 750-526/P Valve Assembly - LPG 60) 910-478 Valve S.I.T. -
Page 22: F38-2 Door Assemblies
106) 940-323/P Side Glass 107) 936-243 Glass Gasket 108) 940-322/P Centre Glass 111) Door Frame Fibre Paper 112) 750-015 Door Glass Extrusion 208) 940-325/P Wrap Glass *Not available as a replacement part. F38-2 DOOR ASSEMBLIES Regency F38-2 Freestanding Gas Stove... -
Page 23: Warranty
Regency Fireplace Products are designed with reliability and simplicity in mind. In addition, our internal Quality Assur- ance Team carefully inspects each unit thoroughly before it leaves our door. Regency Industries Ltd. is pleased to extend this limited lifetime warranty to the original purchaser of a Regency Product. - Page 24 Printed in Canada © Copyright 2007, FPI Fireplace Products International Ltd. All rights reserved.
Need help?
Do you have a question about the F38-NG2 and is the answer not in the manual?
Questions and answers