Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Torque Fitness ANKER-3
Summary of Contents for Torque Fitness ANKER-3
- Page 1 ANKER-3 ASSEMBLY GUIDE VERSION: ANKER-3-001-150LB/200LB/225LB PART #: 5777301-B...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Important safety instructions: • Important safety instructions for using equipment: Page 3 • Important safety instructions for assembling equipment: Page 3 • Obtaining service: Page 3 General Notes: • Unpacking equipment: Page 4 • Tools Required: Page 4 •... -
Page 3: Important Safety Instructions For Using Equipment
Do not disassemble, remove any parts or components or otherwise attempt to repair this product. DO NOT use product if product appears damaged. DO NOT attempt to fix a broken or jammed machine, obtain assistance from your authorized Torque Fitness Dealer. Failure to comply with these instructions will void any and all product warranties. -
Page 4: General Notes
• In a continual effort to improve our page. If any items are missing, contact Torque Fitness products, specifications are subject to Customer service at: 763-754-7533 (8:30 am - 5:00 pm •... -
Page 5: Parts List
ITEM NO. PART NUMBER DESCRIPTION QTY. ITEM NO. PART NUMBER DESCRIPTION QTY. 2031101 SCREW, 3/8" LAG X 2.5"L CLEAR ZINC 57721PA PTD ASSY, LOWER FRAME 2002601 NUT, 1/2 JAM ST ZN 57734PA PTD ASSY, UPPER FRAME BOLT, 3/8-16 X 3/4" (19mm) ST HT SOCKET HEAD 57740PA PTD ASSY, SIDE FRAME 2009402... -
Page 6: Assembly Instructions: Pages
STEP 1 1. ALIGN TAB WITH THE SLOT IN THE LOWER AND UPPER FRAMES. 2. SECURELY TIGHTEN PRE-INSTALLED BOLT TO THE SIDE FRAMES NOTE: Endcaps hidden for assembly clarity NOTE: Position of label SECURELY TIGHTEN bolt connections in this step. - Page 7 Carefully tip the unit up to the wall in desired location. Align slots with the studs and mark drilling locations. Predrill holes as needed for anchoring. ANKER-3 is shown being mounted to a typical wall with wood studs 16" on center. For 24" wall studs follow the same steps as shown.
- Page 8 STEP 3 WARNING: THE ANKER-3 MUST BE ANCHORED TO THE WALL USING EIGHT OR MORE WALL ANCHORS SUITABLE FOR THAT PARTICULAR WALL CONSTRUCTION. Level sides before tightening upper anchor bolts NOTES: The image above shows how to attach the gym to the wall using wall anchors to a typical wood stud wall.
- Page 9 STEP 4 Loosen 1/2 turn Loosen 1/2 turn NOTE: LOOSEN BOLTS 1/2 TURN but do not remove bolts (8). Loosen 1/2 turn NOTES: Loosen bolts to prevent damage to wall when loading plates. Carpet and other soft surfaced flooring may cause movement of the frame when loading weight plates.
- Page 10 STEP 5 TEMPORARILY REMOVE BOLTS, WASHERS, AND NUTS...
- Page 11 STEP 6 NOTE: POSITION OF THREADED HOLES 200 LB OPTION 150 LB OPTION 225 LB OPTION...
- Page 12 STEP 7 NOTE Push down the guide rods and slide collars to the top. Securely tighten set screws. NOTE Install hardware removed in Step 5. Lift up on guide rods and insert bolts. Tighten until hardware doesn't move. Do not crush tube. SECURELY tighten all bolt connections in this step.
- Page 13 STEP 7B Tighten bolts Tighten bolts NOTE: SECURELY TIGHTEN bolts (8) Tighten bolts SECURELY tighten all bolt connections in this step and in previous steps.
- Page 14 STEP 8 FRONT VIEW NOTE: Apply the weight stack labels to the right of the holes on weight plates by following the installation instructions printed on the label. NOTE: Discard labels 16-20 NOTE: After weight stack labels have been applied, use a rubber mallet to carefully install insert plug of the weight stack pin into the center hole of the head plate.
- Page 15 STEP 9 1-1/4" NOTE: ASSEMBLED VIEW SECURELY tighten jam nut. SECURELY tighten all bolt connections in this step.
- Page 16 STEP 10 3) SLIDE OVER CABLE END 2) SLIDE OVER CABLE END 4) ASSEMBLE 48 TO 50 1) SLIDE OVER CABLE END CABLE END ASSEMBLY TO START: ROUTE BALL END IN DIRECTION OF ARROWS. SEE CAUTIONS BELOW. TO END: ONCE THE CABLE IS ROUTED AS SHOWN, THE 2ND CABLE END CAN BE ASSEMBLED.
- Page 17 STEP 11 TO START: THREAD JAM NUT ON TO CABLE END. THREAD CABLE END INTO THE LOWER FRAME AS SHOWN. ROUTE CABLE IN DIRECTION OF ARROWS. SEE CAUTIONS BELOW. REPEAT STEPS FOR BOTH SIDES. TO END: ASSEMBLE CABLE ENDS AS SHOWN BELOW. REPEAT STEPS FOR BOTH SIDES.
-
Page 18: Cable Adjustments
STEP 12 NOTE: If there is a gap between the head plate and first plate, loosen jam nut and turn threaded end counter clockwise until the head plate touches the first plate. SECURELY tighten jam nut. To add tension to the cable, turn the threaded end clockwise. - Page 19 STEP 13 (ACCESSORIES) WARNING: DO NOT DROP WEIGHT STACK WHEN USING PHONE HOLDER NOTE: Magnetic phone holder attachment can be positioned and adjusted to desired height and position.
-
Page 20: Optional Attachments
STEP 14 (OPTIONAL PULL UP ATTACHMENT) 3/8 x 1-3/4" Bolt (2) 3/8" Flat Washer (2) Flanged Spacer (2) NOTE: Mounting hardware is included with the attachment being assembled. SECURELY tighten all bolt connections in this step. -
Page 21: Maintenance
STEP 15 MAINTENANCE: GUIDE RODS: Clean and lubricate with a silicone or teflon base lubricant. NUTS/BOLTS: Tighten and/or adjust as needed. CABLES: Check tension, end fittings, and coating. Replace if damaged or worn. Check jam nuts on cable ends. (NOTICE: NEW CABLES ALWAYS STRETCH DURING USE. -
Page 22: Resistance Ratio Chart
ONE HEAD PLATE FOURTEEN 10 LB PLATES 150 LB STACK ONE HEAD PLATE FOUR 10 LB PLATES 15 LB PLATES 200 LB STACK... - Page 23 ONE HEAD PLATE FOURTEEN 15 LB PLATES 225 LB STACK...
Need help?
Do you have a question about the ANKER-3 and is the answer not in the manual?
Questions and answers