Related Manuals for Screen Innovations Solo 3 Indoor 575 External
Summary of Contents for Screen Innovations Solo 3 Indoor 575 External
- Page 1 Solo 3 Indoor 575 External Installation Instructions INSTALLERS: PLEASE LEAVE THIS MANUAL WITH THE OWNER. Doc. #400184 | v. 1.1 | 25 January 2023...
- Page 2 Scan the QR code to view the SI warranty for this product. Please use this QR Code to access the updated installation instructions and related documents. Technical Support: 512.832.6939 screeninnovations.com Hours of Support: 7:30am – 5pm CST screensupport@screeninnovations.com...
-
Page 3: Table Of Contents
TABLE OF CONTENTS Operating and Care of Your Screen � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4 Before Proceeding �... -
Page 4: Operating And Care Of Your Screen
OPERATING AND CARE OF YOUR SCREEN • Operation of the screen systems should only be performed by responsible parties. • Always check the path of the Solo 3 Screen before operating to ensure that the path is clear of furniture or obstacles that could prevent full operation. Monitor the Solo 3 Screen for smooth operation through its entire range. -
Page 5: Parts In The Box
PARTS IN THE BOX – SOLO 3 575 EXTERNAL – INDOOR Screen Mounting Bracket Options (2/3) Ceiling Mount Brackets Case Assembly RJ45 Coupler Red Straps (AC – 485 screens only) (2/3) Wall Mount Brackets DUOCoup Required IR Remote RF Remote Hardware (1 per RTF screen) (for low voltage 485) -
Page 6: Installation Methods
INSTALLATION METHODS Before installation, determine your installation method according to your product order and installation preferences. The indoor Solo 3 575 External may be installed preassembled or separately (fabric tube and material installed after the cassette). METHOD 1 – Assembled (pgs 8 - 11) METHOD 2 –... -
Page 7: Installation Method 1 - Assembled
METHOD 1 - MOUNTING BRACKETS BEFORE INSTALL– Check upper corners of the opening clearance, as necessary, to prevent interference with the cassette and end caps. Use appropriate fasteners to mount the ceiling brackets to structural supports. Mount brackets between (2–6’’) from the opening ends (additional brackets are intended to prevent cassette sag and should generally be applied to the middle of the cassette). -
Page 8: Mounting Cassette
METHOD 1 - MOUNTING CASSETTE Installation requires two or more people and/or hoisting equipment. Please use safe lifting and rigging techniques. For METHOD 1, lift and secure assembly onto brackets. Once the bracket engages, the cassette will “click” into place. -
Page 9: Mounting Through Bolting Cassette
METHOD 1 - MOUNTING – THROUGH BOLTING CASSETTE NOTE: Be careful not to over-torque or aggressively drill retention hardware when mounting the cassette as deformation to the case could occur; this is especially important when ceiling mounting. The structure behind the mounting points should be flat and level. WARNING! Select a screw or anchor type that has a shallower head profile to eliminate the risk of contact with the screen material roll. -
Page 10: Installation Method 2 - Disassembled
METHOD 2 – UNPACKING NOTE: The following section of the Solo 3 Indoor 575 External instructions applies to separately assembled projects where the cassette is installed prior to the fabric tube and material. Starting with the cassette on a soft, clean surface, remove the screws from the fascia door and open to reveal the inside. -
Page 11: Material Roll Removal
METHOD 2 – MATERIAL ROLL REMOVAL Using the red straps, loop the straps under the material roll, being careful to avoid contact with the material or any obstructions. With the help of the straps on both the ends, slowly pull out material roll and set it aside. -
Page 12: Mounting Cassette
METHOD 2 – MOUNTING CASSETTE Installation requires two or more people and/or hoisting equipment. Please use safe lifting and rigging techniques. Lift and secure the cassette onto the brackets. Once the bracket engages, the cassette will “click” into place. -
Page 13: Material Roll Reinsertion
METHOD 2 – MATERIAL ROLL REINSERTION With the cassette mounted, open the door and slide the material roll with mounting plates on each end into the cassette. Each end will “click” into place as the brackets engage. NOTE: The roll must remain level while installing into the cassette. Fasten the silver safety screws on the mounting plates to secure the material roll. -
Page 14: Fascia Door
METHOD 2 – FASCIA DOOR To close the fascia door, set the door into the cassette; the door will hook in by gravity. Secure with screws. -
Page 15: Installation Ceiling Mount - Moab
INSTALLATION – CEILING MOUNT – MOAB Push cassette all the way to the flanges and ceiling; fine tune as needed with a mounting key. Plug the motor power cable into the barrel connector (AC power), located within the cassette, or the terminal blocks (DC power) to connect Moab (see pages 5 - 7 for power options). -
Page 16: Wiring
INSIDE CASSETTE WIRING – 24V DC 1. Terminate the wires using the provided terminal block, shown below. To head end/equipment connects to bottom terminal To head end/equipment block of Moab Data cable from motor connects 24v Wire: to top terminal Light Grey block of Moab Optional relocation of IR Reciever... -
Page 17: Internal Cassette Wiring - 110V/220V Ac
INSIDE CASSETTE WIRING – 110V/220V AC 1. Terminate the wires with the provided terminal block, as shown below. 2. Locate junction box appropriately. Installer must follow all local electrical codes when connecting 110v AC power. Certified electrician is required to connect pigtail power. To 110v AC To head end/equipment To 110v AC Data cable... -
Page 18: Commissioning Guide Reference
COMMISSIONING GUIDE REFERENCE Moab Quick Start Guide (contains 485 instructions only): Scan the QR code, alternately use the link below to access https://files.screeninnovations.com/Downloads/Installation+Instructions/Connectivity/ moab-quick-start-guide.pdf Note: to get more detailed instructions refer to the Moab installation instructions below. Moab Installation Instructions (contains 485 detailed instructions): Scan the QR code, alternately use the link below to access https://files.screeninnovations.com/Downloads/Installation+Instructions/Connectivity/ moab-installation-instructions.pdf... - Page 19 NOTES...
- Page 20 Screen Innovations 9715-B Burnet Rd, Suite 400 Austin, TX 78758 512.832.6939 www.screeninnovations.com Doc. #400184 | v. 1.1 | 25 January 2023...