Hitachi SH1 Series Basic Manual page 56

Chapter 4
[AC-30]～[AC-88]
Setting for two-stage Acc/Decel time
Code/Name
AC-30
Acc. time for Multispeed-1
AC-32
Decel. time for Multispeed-1
AC-34
Acc. time for Multispeed-2
AC-36
Decel. time for Multispeed-2
AC-38
Acc. time for Multispeed-3
AC-40
Decel. time for Multispeed-3
AC-42
Acc. time for Multispeed-4
AC-44
Decel. time for Multispeed-4
AC-46
Acc. time for Multispeed-5
AC-48
Decel. time for Multispeed-5
AC-50
Acc. time for Multispeed-6
AC-52
Decel. time for Multispeed-6
AC-54
Acc. time for Multispeed-7
AC-56
Decel. time for Multispeed-7
AC-58
Acc. time for Multispeed-8
AC-60
Decel. time for Multispeed-8
AC-62
Acc. time for Multispeed-9
AC-64
Decel. time for Multispeed-9
AC-66
Acc. time for Multispeed-10
AC-68
Decel. time for Multispeed-10
AC-70
Acc. time for Multispeed-11
AC-72
Decel. time for Multispeed-11
AC-74
Acc. time for Multispeed-12
AC-76
Decel. time for Multispeed-12
AC-78
Acc. time for Multispeed-13
AC-80
Decel. time for Multispeed-13
AC-82
Acc. time for Multispeed-14
AC-84
Decel. time for Multispeed-14
AC-86
Acc. time for Multispeed-15
AC-88
Decel. time for Multispeed-15
・Individual Acc/Decel times can be set for multispeed
functions[Ab-11]～[Ab-25].
This will be effective only for Acc./Dec.
time if the set frequency is the same.
Speed 3 [Ab-13],
Speed 4 [Ab-14]
Speed 2 [Ab-12]
Speed 1 [Ab-11]
Acc. 1 Acc. 3
Acc. 2
Acc/decel time
[AC-30] [AC-34] [AC-38]
Speed 1 Speed Speed
Multispeed
2
FW
Range (unit) Unit value
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00～
3600.00(s)
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
Same
Decel. 3 Acc. 4 Decel. 3
Acc. 4 Decel. 4
as
[AC-40] [AC-42] [AC-40] [AC-42] [AC-44]
before
Speed Speed Speed Speed
Speed 4
3 2 4 3 1
For parameter configuration
2nd motor When Intelligent Input terminal 024[SET] is enabled.
Code/Name
AC215 Select method to switch to
Acc2/Decel2 Profile, 2nd-motor
AC216 Acc1 to Acc2 frequency
transition point, 2nd-motor
AC217 Decel1 to Decel2 frequency
transition point, 2nd-motor
AC220 Acceleration time 1, 2nd-motor
AC222 Deceleration time 1, 2nd-motor
AC224 Acceleration time 2, 2nd-motor
AC226 Deceleration time 2, 2nd-motor
Torque control function setting
Code/Name
Ad-01
Torque reference input
source selection
Ad-02
Torque reference value
setting
Ad-03
Polarity selection for
torque reference
Ad-04
Switching time of speed
control to torque control
・Operations settings of torque control.
For more information, refer to the User's guide.
Torque bias setting
Code/Name
Ad-11
Torque bias input
source selection
Ad-12
Torque bias value setting
Ad-13
Polarity selection for torque bias
Ad-14
Terminal [TBS] active
・For setting the torque bias.
For more information, refer to the User's guide.
Speed limitation for torque control
Code/Name
Ad-40
Input selection for
speed limit at torque control
Ad-41
Speed limit at torque
control (at Forward rotation)
Ad-42
Speed limit at torque
control (at Reverse rotation)
・In middle of the torque control the speed limit can be
set.
For more information, refer to the User's guide.
*1) 00(Disable) /01 (Setting by Terminal [Ai1]) /02 (Setting by Terminal
[Ai2]) /03(Setting by Terminal [Ai3]) /04 (Setting by Terminal [Ai4]) /05
(Setting by Terminal [Ai5]) /06 (Setting by Terminal [Ai6]) /07 (Setting by
parameter) /08 (Setting by RS485) /09 (Option-1) /10 (Option-2) /11
(Option-3) /12 (Pulse train input(internal)) /13 (Pulse train
input(Option)) /14 (Setting by EzSQ) /15 (PID function)
4-13
[AC215]～ [Ad-15]
Range (unit) Initial value
Same as AC115
Same as AC116
Same as AC117
Same as AC120
Same as AC122
Same as AC124
Same as AC126
Initial
Range (unit)
value
00～15 *1) 07
-500.0～500.0(%) 0.0
00(According to
sign)/
00
01(Depend on the
operation direction)
0～1000(ms) 0
Initial
Range (unit)
value
00～15 *1) 00
0.0
-500.0～500.0(%)
00(According to
sign)/
00
01(Depend on the
operation direction)
00(Disable)/
00
01(Enable)
Range (unit) Initial value
01～13 *1) 07
0.00
0.00～
590.00(Hz)
0.00