Related Manuals for Moxa Technologies NPort W2150A-W4 Series
Summary of Contents for Moxa Technologies NPort W2150A-W4 Series
- Page 1 NPort W2150A-W4/ NPort W2250A-W4 Series Quick Installation Guide Version 1.1, January 2023 Technical Support Contact Information www.moxa.com/support 2023 Moxa Inc. All rights reserved. P/N: 1802021503052 *1802021503052*...
-
Page 2: Package Checklist
Overview The NPort W2150A-W4/W2250A-W4 wireless device servers are an ideal choice for connecting serial devices or Ethernet devices, including PLCs, meters, and sensors, to an IP-based wireless LAN or Ethernet LAN. Features • Links serial and Ethernet devices to an IEEE 802.11a/b/g/n network •... -
Page 3: Hardware Introduction
ATTENTION 이 기기는 업무용 환경에서 사용할 목적으로 적합성 평가를 받은 기기로서 가정용 환경에서 사용하는 경우 전파간섭의 우려가 있습니다. ATTENTION 「取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不 得擅自變更頻率、加大功率或變更原設計之特性及功能。低功率射頻器材 之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即 停用，並改善至無干擾時方得繼續使用。前述合法通信，指依電信管理法 規定作業之無線電通信。低功率射頻器材須忍受合法通信或工業、科學及 醫療用電波輻射性電機設備之干擾。」 「應避免影響附近雷達系統之操作。」 NOTE Before connecting the NPort W2150A-W4 and NPort W2250A- W4 Series DC power inputs, make sure the DC power source voltage is stable. - Page 4 NPort W2150A-W4 NPort W2250A-W4 NPort W2150A-W4-T NPort W2250A-W4-T Reset Button: The reset button is used to load the factory default settings. Use a pointed object to hold the reset button down for five seconds to load the factory defaults. Name Color Function End Panel LED Indicators...
- Page 5 Name Color Function 1 Red - The signal strength (RSSI) is lower than -88 dBm. 2 Red - The signal strength (RSSI) is between -87 to -79 dBm. Signal 3 Green - The signal strength (RSSI) is between Strength -78 to -68 dBm. 4 Green - The signal strength (RSSI) is between Green...
-
Page 6: Wall Mounting (Optional)
First-Time Hardware Installation STEP 1: After removing the NPort W2150A-W4/W2250A-W4 from the box, use a crossover Ethernet cable to connect the NPort’s RJ45 Ethernet port directly to your computer’s Ethernet port. STEP 2: Attach the power adapter to the NPort and then plug the adapter into an electrical outlet. -
Page 7: Software Installation
Software Installation For the NPort’s configuration, the default IP address of the NPort is: LAN: Static; IP = 192.168.126.254; netmask = 255.255.255.0 WLAN: Static; IP = 192.168.127.254; netmask = 255.255.255.0 If the NPort is configured for DHCP, but the DHCP server cannot be found, then the NPort will use the factory default IP settings. -
Page 8: Pin Assignments And Cable Wiring
Pin Assignments and Cable Wiring RS-422, RS-232 2w RS-485 4w RS-485 TxD-(A) – TxD+(B) – RxD+(B) Data+(B) RxD-(A) Data-(A) – – – – – – – – – Specifications Power Requirements Power Input 12 to 48 VDC Input Rating 1-port: 12 to 48 VDC, max 429 mA @ 12 VDC 2-port: 12 to 48 VDC, max 455 mA @ 12 VDC Power Connector Screw-type power jack or terminal block (only one...