Page 11
8. READ the instructions of test equipment throughly before connecting a test equipment to the transceiver. Icom, Icom Inc. and ICOM logo are registered trademarks of Icom Incorporated (Japan) in the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries.
Page 13
• Antenna impedance • Operating temperature range : –30˚C to +60˚C (–22˚F to +140˚F) • Power supply requirement : Specified Icom's battery pack only (7.2 V DC nominal; negative ground) • Current drain (at 7.2 V DC ; approx.) RECEIVING TRANSMITTING Stand-by Max.
Page 14
SECTION 2. INSIDE VIEWS • MAIN UNIT TOP VIEW BOTTOM VIEW TX/RX switch (D14, D15: MA2S077G0L Pre-drive (Q9: 2SC5110) Power amplifier (Q7: RD07MVS2) AF amplifier (IC12: TA7368FG) +5 Regulator S5 Regulator (IC9: NJM2870F05) Q23: 2SB1132 Q24: XP6501 Q25: UNR9113G0L T5 Regulator (Q21: 2SA1577) Crystal filter Mute switch...
Page 15
SECTION 3. DISASSEMBLY INSTRUCTION 1. REMOVING THE CHASSIS UNIT 2. REMOVING THE MAIN UNIT q Unscrew 1 nut A, and remove 2 knobs B, C. q Unscrew 2 nuts F, and remove the top plate G. w Unscrew 2 screws D. w Unsolder 5 points H, and remove the shield cover.
SECTION 4. CIRCUIT DESCRIPTION 4-1 RECEIVER CIRCUITS 4-1-1 ANTENNA SWITCHING CIRCUIT The antenna switching circuit functions as a low-pass filter The RF signals from the bandpass filter are mixed with the while receiving and a resonator circuit while transmitting. 1st LO signals, where come from the RX VCO circuit via the This circuit does not allow transmit signals to enter the attenuator (R26–R28), at the 1st mixer circuit (Q3) to pro- receiver circuits.
4-1-5 AF AMPLIFIER CIRCUIT • CTCSS AND DTCS The tone squelch circuit detects tone signals and opens the The AF amplifier circuit amplifies the demodulated AF sig- squelch only when receiving a signal containing a matched nals to drive a speaker. subaudible tone (CTCSS or DTCS).
Page 18
4-2-2 MODULATION CIRCUIT 4-2-4 APC CIRCUITS The modulation circuit modulates the VCO oscillating signal The APC circuit (IC2, D1) protects drive and power ampli- (RF signal) using the microphone audio signals. fiers from the reflected signal, and selects output power of HIGH, LOW2 or LOW1.
4-3-2 VCO CIRCUIT 4-3 PLL CIRCUITS The VCO circuit contains a separate RX VCO (Q14, D19, 4-3-1 PLL CIRCUIT D20) and TX VCO (Q13, D16, D17, D21). The oscillated A PLL circuit provides stable oscillation of the transmit signal is amplified by the buffer amplifiers (Q10, Q12) and frequency and receive 1st LO frequency.
4-6 PORT ALLOCATION 4-4 OTHER CIRCUITS LED CONTROL CIRCUITS 4-6-1 D/A CONVERTER IC (IC8) The LED control circuit is composed of the LED driver (Q32) Port and LED (DS1). Description number name Outputs the modulation balance level The CPU outputs “RLED” and “TLED” signals from the pins control signal.
Page 21
4-6-2 CPU (IC13) Port Port Description Description number name number name Input port for the transceiver’s RLED Outputs receiving LED control signal. TEMP internal temperature detecting Outputs transmitting LED control signal. TLED signal. Input port for the detect signal for BATV connecting battery pack’s voltage.
SECTION 5. ADJUSTMENT PROCEDURE 5-1 PREPARATION ¤ REQUIRED EQUIPMENTS EQUIPMENT EQUIPMENT SPECIFICATION SPECIFICATION Adjustment JIG cable Modifi ed OPC-478U/UC (USB type) or "CS-F3010 ADJ" (Revision 1.0 or later) software (see the page 5-3) OPC-478 (RS-232 type) Frequency range : 300–3000 Hz Power attenuation : 30 dB Audio generator Attenuator...
Page 23
• CONNECTION OPC-478 (RS-232C type) to RS-232C port Standard signal generator to the antenna connector 0.1 µV to 32 mV (–127 dBm to –17 dBm) to USB port OPC-478U DO NOT transmit while (USB type) an SSG is connected to to USB port the antenna connector.
Page 24
(3) Boot up Windows, and click the program group 'CS-F3010 ADJ’ in the ‘Programs’ folder of the [Start] menu, then CS-F3010 ADJ’s window appears. (4) Click ‘Connect’ on the CS-F3010’s window, then IC-F3011/IC-F3013’s up-to-date condition appears as below. (5) Set or modify adjustment value as specified in the following guidances.
5-2 FREQUENCY ADJUSTMENT 1) Select an adjustment item using cursor or [↑] / [↓] of the PC’s keyboard. 2) Set or modify the adjustment value as specifi ed using [←] / [→] of the PC’s keyboard, then push [ENTER]. ADJUSTMENT ADJUSTMENT ADJUSTMENT CONDITION OPERATION...
5-3 TRANSMIT ADJUSTMENT 1) Select an adjustment item using cursor or [↑] / [↓] of the PC’s keyboard. 2) Set or modify the adjustment value as specifi ed using [←] / [→] of the PC’s keyboard, then push [ENTER]. ADJUSTMENT ADJUSTMENT ADJUSTMENT CONDITION OPERATION...
5-2 RECEIVE ADJUSTMENT 1) Select an adjustment item using cursor or [↑] / [↓] of the PC’s keyboard. 2) Set or modify the adjustment value as specifi ed using [←] / [→] of the PC’s keyboard, then push [ENTER]. ADJUSTMENT ADJUSTMENT ADJUSTMENT CONDITION OPERATION...
Page 28
SECTION 6. PARTS LIST [CONNECT UNIT] [MAIN UNIT] PARTS PARTS DESCRIPTION DESCRIPTION LOCATION LOCATION C501 4030017460 S.CER ECJ0EB1E102K 8.3/5.3 1110003201 S.IC TA31136FNG(EL) 51.8/19 C502 4030016930 S.CER ECJ0EB1A104K 9.3/5.3 1110002751 S.IC TA75S01F(TE85R,F) 68.9/21 1140005991 S.IC MB15A02PFV1-G-BND-ERE1 38.3/35.7 1110005340 S.IC NJM12902V-TE1-#ZZZB 29.7/11.6 J501 6910016390 CON IMSA-9230B-1-02Z145-PT1...
Page 29
[MAIN UNIT] [MAIN UNIT] PARTS PARTS DESCRIPTION DESCRIPTION LOCATION LOCATION 6200007750 S.COI LQW2BHN56NJ03L 70.6/37.8 7030008370 S.RES ERJ2GEJ 561 X (560) 54.6/34.1 6200008090 S.COI LQW2BHN68NJ03L 64/40.2 7030008370 S.RES ERJ2GEJ 561 X (560) 54.6/32.4 6200007850 S.COI ELJNC R82K-F 66.8/33.9 7030005050 S.RES ERJ2GEJ 103 X (10K) 50.8/36.8 6200002861 S.COI NLV25T-4R7J...
Page 30
[MAIN UNIT] [MAIN UNIT] PARTS PARTS DESCRIPTION DESCRIPTION LOCATION LOCATION R201 7030005240 S.RES ERJ2GEJ 473 X (47K) 23.9/14.9 4030017580 S.CER ECJ0EC1H060C 83.4/37.7 R206 7030005110 S.RES ERJ2GEJ 224 X (220K) [CSA-01] T 13.4/4.1 4030017430 S.CER ECJ0EC1H101J 78.2/33.4 7030005110 S.RES ERJ2GEJ 224 X (220K) [CSA-02] 4030017460 S.CER ECJ0EB1E102K 78.8/35.7 R207...
Page 32
SECTION 7. MECHANICAL PARTS [CHASSIS PARTS] [ANT UNIT] ORDER ORDER DESCRIPTION QTY. DESCRIPTION QTY. MP601 8510016350 2721 ANT PLATE 6910015910 ANT CONNECTOR 104 6910015860 IMSA-6277S-O2A-G 2510001530 PSC-3650P-0806A2 <PRI> [CONNECT UNIT] 8900009640 OPC-963 ORDER DESCRIPTION QTY. 8010019696 2775 CHASSIS-6 8210024550 2775 A-FRONT PANEL (Incl. MP3, 4, 5, 43) J501 6910016390 IMSA-9230B-1-02Z145-PT1 8210024560 2775 A-PTT PANEL...
Page 33
MP13(C) J1(C) MP36(C) MP35(C) MP8(C) MP31(C) MP1(C) MP17(C) ANT Unit S1(C ) MP29( C ) W2 ( C ) CONNECT Unit MP30( C ) S4 ( M ) MP32(C) R226 ( M ) MAIN Unit MP14(C) MP28 ( C ) MP25 ( C ) MP11 ( C ) J2(C)
Need help?
Do you have a question about the IC-F3011 and is the answer not in the manual?
Questions and answers