Related Manuals for Metec Telescopic Angle Plow
Summary of Contents for Metec Telescopic Angle Plow
- Page 1 Telescopic Angle Plow OWNER'S MANUAL METEC Metal Technology Inc. 613-678-3957 info@metec.ca 2021...
-
Page 2: Table Of Contents
Warranty ..............................24 DISCLAIMER METEC Metal Technology Inc. provides this publication "as is" without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual METEC assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. -
Page 3: Understanding The Manual
Refer to the model and serial number when requesting parts or service. Enter your serial number and date of purchase in the space provided below. MODEL NUMBER SERIAL NUMBER DATE OF PURCHASE METEC Metal Technology Inc. 613-678-3957 info@metec.ca... -
Page 4: Safety Information
SAFETY INFORMATION General safety practices are listed on the safety information pages and specific safety information is located throughout this manual. SAFETY SYMBOL IMPORTANT Indicates that equipment or This is the safety alert symbol. property damage could result if It is used in the manual and on instructions are not followed. safety labels to remind operators and repair personnel of important safety practices and procedures. -
Page 5: Owners' Responsibilities
Unauthorized persons are prohibited around the vehicle and equipment area while in operation! Spotters, safety personnel are essential during all operations and maintenance. All safety instructions and hazard warning stickers must be kept legible. Replacements may be purchased from your distributor. METEC Metal Technology Inc. 613-678-3957 info@metec.ca... -
Page 6: Important Precautions
Important Precautions to take to avoid accidents Notify your service department immediately if maintenance is required that poses a risk to humans, animals, property and other. Do not attempt maintenance work while machine is running. Engine must be turned off and ignition key removed! Refer to your internal lock-out and safe working procedure. -
Page 7: Safety Rules
Wear protective gloves and safety glasses or goggles when working with hydraulic systems. SEEK MEDICAL ATTENTION. If an accident occurs, see a doctor familiar with this type of injury immediately. Any fluid injected into the skin or eyes must be treated within a few hours or gangrene may result. Damaged hydraulic hoses must be replaced immediately. Only certified personnel are to service the hydraulic systems. METEC Metal Technology Inc. 613-678-3957 info@metec.ca... -
Page 8: General Safety Guidelines
GENERAL SAFETY GUIDELINES Prior to operation, the equipment must be thoroughly inspected and every operator must have a clear understanding of the potential dangers inherent with the operation of this equipment. 2. Children and equipment do not mix; do not allow children to play on or around the equipment or work area. -
Page 9: Safety During Operation
4. Remove chute or other visual obstructions to insure a clear view of the road way. 5. Spotter, warning signs, lights and acoustic signals are recommended for safe transportation. METEC Metal Technology Inc. 613-678-3957 info@metec.ca... -
Page 10: Warning Labels
Warning labels Listed below are all our Warning Labels. Some of these labels might not be required for your attachment. Please refer to the “Location of Labels” picture on the following page. Figure 1 Figure 2 Figure 3 Figure 6 Figure 7 Figure 4 Figure 5... - Page 11 9 “Grease Nipple” label MET-009 Figure 9 10 “Slow Moving Vehicle” label MET-010 Figure 10 11 “Shear Bolt” label MET-012 Figure 11 12 “METEC logo” label MET-013 Figure 12 13 “Rotation” label MET-014 Figure 13 14 “Crush Zone” label MET-015 Figure 14 15 “PTO Rotation Direction”...
-
Page 12: Location Of Labels
1. Figure 1 — MET-001 2. Figure 12 — MET-015 “Caution” Label “Pinch Point” Label 3. Figure 7 — MET-009 4. Figure 6 — MET-008 “Grease Nipple” Label “Refer to Manual” Label 5. Figure 10 — MET-013 “METEC Logo” Label... -
Page 13: General Operating Instructions
3. Do not wear loose clothing when operating the equipment. 4. Use extreme caution when operating on gravel surfaces as the telescopic angle plow may dig into the gravel and cause the tractor to swerve or stop suddenly as well as throwing gravel or debris. -
Page 14: Maintenance
2. Secure hydraulic hoses to prevent chafing against other parts. 3. Upon reception of your new Telescopic Angle Plow and after 20 operational hours, re- torque all the bolts. 4. Tighten and check bolts prior to operating and then every 3-4 hours of operation. -
Page 15: Maintenance Record
MAINTENANCE RECORD Use this log to record maintenance performed on your unit. Type of maintenance Performed by Comments Date and time performed METEC Metal Technology Inc. 613-678-3957 info@metec.ca... -
Page 16: Bolt Torque Specifications
= nominal thread diameter in millimeters x thread pitch The nominal torque values listed are for general use only with the assumed wrenching accuracy of 20%, such as a manual torque wrench. METEC will not assume any responsibility for errors and omissions in the above chart. DO NOT use these values if a different torque value or tightening procedure is given for a specific application. -
Page 17: Imperial And Metric Conversion Tables
Cubic Yards . 1.308 Milliliters Fluid Ounces 0.034 Liters Pints 2.113 Liters Quarts 1.057 Liters Gallons 0.264 Kilograms Pounds 2.205 Newton-Meters Pound-feet 0.738 Pounds per Square Inch 14.50 Kilometers per Hour Miles per Hour 0.621 METEC Metal Technology Inc. 613-678-3957 info@metec.ca... -
Page 18: Parts
Parts List Telescopic Angle Plow Illustrations may not necessarily reproduce the full detail and exact shape of the parts or depict the actual models and are intended for reference only. Please include the model, make, serial number, and the part number to place an order. - Page 19 Notes METEC Metal Technology Inc. 613-678-3957 info@metec.ca...
- Page 21 METEC Metal Technology Inc. 613-678-3957 info@metec.ca...
- Page 23 METEC Metal Technology Inc. 613-678-3957 info@metec.ca...
-
Page 24: Warranty
METEC. b. If different lubricants as those prescribed by 2. METEC undertakes to repair or replace free of METEC are used; charge, all components proved to be defective c. For damaged parts on which repairs or... - Page 25 Warranty requests can only be considered by METEC once they are in possession of the said defective parts. 4. If the warranty case is accepted by METEC; the inquirer will obtain a credit note a. for the replaced parts b. for the spent working time, according to the standard time-rate of METEC or third suppliers.
- Page 26 MANUFACTURER Tel. Email 1 613-678-3957 info@metec.ca METEC Metal Technology Inc. 20 Terry Fox Drive, Vankleek Hill Ontario, Canada, K0B 1R0 www.metec.ca 1 613-678-3956 All Rights to this document and its contents are reserved by METEC Metal Technology Inc.
Need help?
Do you have a question about the Telescopic Angle Plow and is the answer not in the manual?
Questions and answers