Subscribe to Our Youtube Channel
Related Manuals for Draper 98921
Summary of Contents for Draper 98921
- Page 1 Version 2: September 2022 230V SUBMERSIBLE DEEP WATER WELL PUMP WITH FLOAT SWITCH 98921...
-
Page 2: Preface
All photographs and drawings within this manual are document is part of the product; retain it for the life supplied by Draper Tools to help illustrate correct of the product, passing it on to subsequent holders. operation of the product. -
Page 3: Table Of Contents
2. Contents Preface 1.1 Product Reference 1.2 Revisions 1.3 Understanding the Safety Content of This Manual 1.4 Copyright © Notice Contents Warranty Product Introduction 4.1 Scope 4.2 Specification Health and Safety Information 5.1 General Health and Safety Precautions 5.2 Additional Safety Information for This Submersible Water Pump 5.3 Connection to the Power Supply 5.4 Residual Risk Identification and Unpacking... -
Page 4: Manual
This warranty period covers parts and labour for 12 months from the date of Your Draper Tools guarantee is not effective until you can purchase. Where tools have been hired out, the warranty produce, upon request, a dated receipt or invoice to period covers 90 days from the date of purchase. -
Page 5: Product Introduction
Where the pump is used temporarily in a fish pond, Draper Tools STRONGLY recommends that the fish are removed for the duration of operation or a guard is placed around the pump inlet to prevent fish from being drawn into the mechanism. -
Page 6: Health And Safety Information
• If the supply cord is damaged, it must be replaced by operating current of no greater than 30mA. Draper Tools or its authorised service agent in order to avoid a hazard. • ONLY connect the pump to a power supply matching the rated voltage of the product. -
Page 7: Connection To The Power Supply
If the power supply cord is damaged, it must be replaced clamp recess during use. by Draper Tools, an authorised service agent or similarly qualified personnel in order to avoid a hazard. • The float switch attached to this product is NOT suitable for continuous use as an ON/OFF switch. -
Page 8: Identification And Unpacking
Carefully remove the product from the packaging and examine it for any signs of damage that may have occurred during shipment. If any part is damaged or missing, do not attempt to use the product. Please contact the Draper Helpline; contact details can be found at the back of this manual. -
Page 9: Packaging
6. Identification and Unpacking 6.2 Packaging WARNING! Keep packaging materials out of reach of children. Dispose of packaging Keep the product packaging for the duration of the correctly and responsibly and in accordance warranty period for reference should the product need to with local regulations. -
Page 10: Preparation Instructions
Important: Draper Tools recommends that clear water 7.1 Using the Outlet Adaptors pumps are used ONLY in reservoirs that are completely free from debris. -
Page 11: Positioning The Float Switch
7. Preparation Instructions Pump on above this level CAUTION! Draper Tool recommends that the pump is fully submerged before it is connected to the mains power and remains submerged throughout the entire operation. This ensures that the motor remains cool during use. DO NOT Pump off below this level run the pump when it is dry. -
Page 12: Operating Instructions
8. Operating Instructions Important: To prevent the pump from overheating, Draper Tools strongly recommends that the pump remains completely submerged for the entire operation. Exposure of the motor housing above the water level may cause the motor to overheat and damage the product from the inside. -
Page 13: Maintenance And Troubleshooting
Technical maintenance and servicing may ONLY be performed by authorised Draper Tools service agents. 9.1 General Care and Storage • Periodically flush the pump through with fresh clean water, particularly if it is left in water for extended periods or it has not been used for some time. -
Page 14: Troubleshooting
The power cable or plug is faulty. DO NOT continue to use the product. Contact Draper Tools for repair and replacement options. The fuse in the plug has blown. Replace the fuse. The residual circuit breaker has tripped. -
Page 15: Spares, Returns And Disposal
Draper Tools will invalidate your warranty. Important: ALWAYS drain and clean the product of any water and debris before returning it to Draper Tools or its authorised agent. A charge may be applicable if Draper Tools must clean the product before investigating a fault. -
Page 16: Explanation Of Symbols
11. Explanation of Symbols IP rated for continuous submersion of Read the instruction manual over 1m Warning! Class I appliance Rated input WEEE – Waste Electrical & Electronic Equipment Do not dispose of Waste Electrical & Electronic Equipment in with domestic rubbish Max. -
Page 17: Notes
Notes – 17 –... - Page 18 Telephone Sales Desk: +44 (0) 23 8049 4333 General Enquiries: +44 (0) 23 8026 6355 General Fax: +44 (0) 23 8026 0784 Please contact the Draper Tools Product Helpline for repair and servicing enquiries. © Published by Draper Tools Limited © Published by Draper Tools Limited...
Need help?
Do you have a question about the 98921 and is the answer not in the manual?
Questions and answers