Page 2
The trademarks, logos and service marks ("Marks") displayed in this documentation are the property of Arista Networks in the United States and other countries. Use of the Marks are subject to Arista Network Term of Use Policy, available at http://www.arista.com/en/terms-of-use. Use of marks belonging to other parties is for...
Chapter 1 Overview This Quick Start Guide (QSG) describes the CCA-ETM-Q12 appliance. This chapter contains the following topics: • Scope • Receiving and Inspecting the Equipment • Installation Process • Safety Information • Obtaining Technical Assistance • Specifications Scope This guide is intended for properly trained service personnel and technicians who need to install the following Arista appliance: This guide is covers the CCA-ETM-Q12 appliance.
Ultimate disposal of this product should be handled in accordance with all national laws and regulations. Aucune pièce réparable par l'utilisateur à l'intérieur. Confiez toute réparation à un technicien qualifié. Safety Information Refer to the Arista Networks document Safety Information and Translated Safety Warnings available at: https://www.arista.com/en/support/product-documentation.
Overview Obtaining Technical Assistance Any customer, partner, reseller, or distributor holding a valid Arista Service Contract can obtain technical support in any of the following ways: • Email: http://support@arista.com. This is the easiest way to create a new service request.
Chapter 2 Preparation This section describes the initial setup and preparation for installing the CCA-ETM-Q12. This chapters contains the following topics: • Site Selection • Tools Required for Installation • Electrostatic Discharge (ESD) Precautions Site Selection The following criteria should be considered when selecting a site to install the appliance.
Tools Required for Installation These are the tools needed to install the CCA-EMT-Q12 appliance. Table 4: Tools required for installation 1 #2 Phillips screwdriver Electrostatic Discharge (ESD) Precautions Observe these guidelines to avoid ESD damage when installing or servicing the appliance. •...
Chapter 3 Mounting the Appliance The appliance is mounted onto a four-post rack by preparing the chassis for mounting, then securing the appliance to the front posts using the mounting brackets, followed by securing it to the rear posts. The installation kit provides the following four-post mounting parts: •...
Mounting the Appliance Rack Mounting the Appliance 1 Mounting screws 3 Mounting screws 2 Left bracket 4 Right bracket 1. Align the left bracket to the left face plate. 2. Attach the left front mounting bracket using three mounting screws. 3.
Page 11
Mounting the Appliance 1 Back rack post 4 Front rack post 2 Back bracket 5 Front bracket 3 Mounting screws 6 Mounting screws 1. Insert the appliance into the racking at the predetermined height within the left side of the rack. 2.
Chapter 4 Cabling the Appliance This procedure is for the attachment of power and network cables to the appliance. 1. Connect an Ethernet cable from your Internet provider modem or router to the designated Internet port. 2. Connect an Ethernet cable from your management computer or LAN switch to port 1. 3.
You can manage your appliance using the Edge Threat Management Dashboard or from the local network. From Edge Threat Management Dashboard 1. Navigate your web browser to http://edge.arista.com/cmd. 2. Log in with your Edge Threat Management Dashboard account, or click Create Account to set up an account.
Appendix A Status Indicators Front Status Indicators This section describes the front panel LED status of the CCA-ETM-Q12 appliance. Figure 1: CCA-ETM-Q12 Front Status Indicators 1. LAN ports 2. Storage activity...
Page 15
1. Back brackets (2) 4. Power cable 2. Mounting brackets (2) 5. Racking mounting screws (10) 3. Mounting rails (2) 6. Appliance mounting screws (6) The CCA-ETM-Q12 package includes: • Power cable. • Rack mounting hardware. • The CCA-ETM-Q12 appliance.
Regulatory Model Numbers This appendix lists the Regulatory Model Numbers (RMNs), where applicable, for the product models for the appliances described in this document. Table 5: Regulatory Model Numbers and Product Numbers Regulatory Model Number (RMN) Product Number(s) AN2203, CAR-3070-5C21-E90 CCA-ETM-Q12...
Appendix F Taiwan RoHS Information This appendix provides Taiwan RoHS information for appliances covered by this guide. For Taiwan BSMI RoHS Table, go to https://www.arista.com/assets/data/pdf/AristaBSMIRoHS.pdf.
Need help?
Do you have a question about the CCA-ETM-Q12 and is the answer not in the manual?
Questions and answers