Page 1 MAGIC THipPro (Pure) Lite Configuration Guide Version: 3.810 (09. January 2023) info@avt-nbg.de www.avt-nbg.de © AVT Audio Video Technologies GmbH...
Page 2: Table Of Contents
Content ▪ Documents ▪ Configuration ▪ System Settings ▪ Overview Date and Time and Login ▪ ▪ Hardware ▪ Operation Settings Basic Features ▪ Local Settings ▪ ▪ Optional Features ▪ Factory Settings Accessories ▪ ▪ Maintenance ▪ PC Software Resources Backup / Restore ▪...
Page 3 Additional Documents Get further information in the following documents which are available in ▪ the Download section of our website at www.avt-nbg.de. Quick Guides: ▪ Audio over IP (AES67-DANTE-RAVENNA-LIVEWIRE) ▪ ▪ Signalling and Control with DHD SetLogic Signalling and Control with Ember+ ▪...
Page 4: Overview
MAGIC THipPro Lite Overview ▪ Hardware ▪ Basic Features ▪ Optional Features Accessories ▪ info@avt-nbg.de www.avt-nbg.de © AVT Audio Video Technologies GmbH...
Page 5 Hardware – Front ▪ Five Status LEDs ▪ Two RJ10 Handset/Headset interfaces for PRETALK (Not available for MAGIC THipPro Pure ▪ POWER Lite). SYNC (On while booting) ▪ ▪ ALARM (Indicating hardware problems) ▪ Illuminated graphic display with 160 x 32 pixels & front keypad.
Page 6 THipPro Lite Hardware – Rear ▪ Two independent LAN interfaces ▪ 2 x AES3/EBU stereo audio in-/outputs (Digital AES 3 -4, licence required) Up to three VLANs per LAN interface ▪ 4 digital audio lines (Sub-D 15-pole with adaptors ▪ Word clock input/output ▪...
Page 7 Word clock input/output ▪ The configuration described in this manual refers ▪ to the MAGIC THipPro Lite with physical audio Programmable GPIO interface ▪ interfaces, but also applies to the MAGIC THipPro Pure Lite. Any reference to the physical audio ▪...
Page 8 Hardware – Module slots 1 and 2 ▪ POTS ▪ RAVENNA ▪ 2 x POTS modules for 8 caller lines ▪ 32 channels in/out 2 Ethernet interfaces ▪ DANTE ▪ ▪ Only for VoIP systems 32 channels in/out ▪ The standard Audio interfaces can still be used ▪...
Page 9: Basic Features
Basic Features (1) Housing 19” x 1 U Digital signal processing for each channel ▪ ▪ Leave 1U space above the unit for cooling. Echo Canceller with up to 120 ms echo tail time ▪ ▪ ▪ AGC Automatic Gain Control No fan for noiseless operation ▪...
Page 10 ▪ Audio test panel with signal generator ▪ 96 GPIOs, each configurable as input or output ▪ ▪ MAGIC THipPro Lite Software ▪ Predefined GPIOs for a dialling keypad Touch optimized Windows PC software for ▪ Ember+ Provider Support ▪...
Page 11: Optional Features
Optional Features (1) VoIP + HD-Voice Option MAGIC THipPro Full Upgrade ▪ ▪ For 4 or 8 channels Including SQL Database and Digital Audio ▪ ▪ ▪ -Voice (G.722) ▪ Available for THipPro Lite with 8 VoIP or 8 POTS lines ▪...
Page 12 Optional Features (2) AES67 Dante Module ▪ ▪ Audio over IP networking software upgrade. Audio over IP networking hardware upgrade. ▪ ▪ ▪ Output: 8 audio channels (1 stream). ▪ 32x32 audio channels. Input: 8 audio channels (2 streams). Supports AES67 for interconnection with Ravenna, ▪...
Page 13 Ember+ Consumer Extension MAGIC System Manager ▪ ▪ Connect up to 6 third party workplaces using only Access the MAGIC THipPro Lite from AVT’s central ▪ ▪ Ember+ and DHD SetLogic. management software which supports all AVT telephone hybrids and audio codecs.
Page 14: Accessories
Accessories MAGIC PhonerSet ▪ MAGIC THipPro Lite Handset ▪ MAGIC THipPro Lite Headset ▪ ▪ USB Headset ▪ For Pretalk Audio Streaming USB Handset ▪ For Pretalk Audio Streaming ▪...
Page 15: Pc Software
8000 x 6000 px. ▪ Automatic scaling for high- DPI screens. ▪ Up to 8 clients can access the system simultaneously. Optional MS SQL Server ▪ backend database Each client has direct access ▪ to the MAGIC THipPro Lite unit.
Page 16: Resources
Resources The AVT MAGIC THipPro Lite unit comes with a ▪ USB Flash Drive including the current PC software, firmware and the manual. The latest version of the MAGIC THipPro Lite ▪ software is freely available in the download section of our website http://www.avt-nbg.de.
Page 18: Initial Setup
Configure the IP address of the LAN interface via ▪ the front display as shown on the right. The MAGIC THipPro Lite can be configured to use ▪ DHCP later via the PC software on the LAN INTERFACE configuration page.
Page 19: Connecting The Pc Software
MAGIC THipPro Lite Connecting the software info@avt-nbg.de www.avt-nbg.de © AVT Audio Video Technologies GmbH...
Page 20 ▪ MAGIC THipPro Lite (default: 10000). the software. Run the software as administrator. ▪ Right click the MAGIC THipPro Lite icon on the ▪ desktop and select Run as administrator. ▪ Make sure to have the MAGIC THipPro Lite connected to the local network.
Page 21 MAGIC THipPro Lite PC software (2) If the PC software doesn’t get an answer from ▪ the MAGIC THipPro Lite it will show NO CONNECTION in the upper right corner. When the LAN Client software connects to a ▪ MAGIC THipPro Lite with factory settings the main panel is empty.
Page 23: First Steps
First steps (2) In the PC software go to Menu > Configuration > System > Operation Settings > Clients / Security. ▪ Enter the Windows device names or IP addresses of the PCs which should access the THipPro Lite. ▪ ▪...
Page 24: Possible Applications
MAGIC THipPro Lite Possible Applications info@avt-nbg.de www.avt-nbg.de © AVT Audio Video Technologies GmbH...
Page 25 1 Studio / One Fader LAN: PC Client 1 PRETALK ON AIR 1...
Page 26 1 Studio / Two Faders LAN: PC Client 1 ON AIR 2 ON AIR 1 PRETALK...
Page 27 1 Studio / Eight Faders LAN: PC Client 1 PRETALK ON AIR 1-8...
Page 28 2 Studios / One Fader PRETALK PRETALK LAN: LAN: PC Client 1 PC Client 5 ON AIR 2 ON AIR 1...
Page 29 2 Studios / Two Faders PRETALK PRETALK LAN: LAN: PC Client 1 PC Client 5 ON AIR 3 / 4 ON AIR 1 / 2...
Page 30 2 Studios / Two Faders PRETALK PRETALK LAN: LAN: PC Client 1 PC Client 5 ON AIR 5 - 8 ON AIR 1 - 4...
Page 31: System Settings
MAGIC THipPro Lite System Settings info@avt-nbg.de www.avt-nbg.de © AVT Audio Video Technologies GmbH...
Page 32 General (1)
Page 33 CONTRAST: Adjust the contrast to improve the ▪ MAGIC THipPro Lite systems with different indexes ▪ clarity of the front display. will not show each others call history. ▪ MAGIC THipPro Lite systems using the same index will show the same call history. General (2)
Page 34 Line Interface (1)
Page 35 ▪ LINE MODE: Specifies the type of telephone POTS gateway with up to 8 analogue telephone network the MAGIC THipPro Lite is connected to. lines. The POTS gateway must be purchased from AVT. VOIP (LAN/SIP): Voice over IP provides digital audio ▪...
Page 36 IN-HOUSE LINES: Specify lines connected to a PBX. ▪ DISABLE LOCK FUNCTION: If enabled, a line can ▪ Required to distinguish between internal and not be locked by pressing the DROP button on a external calls. Prefix digits for dialling external disconnected line.
Page 37 ANONYMOUS CALLING: Checked channels signal ▪ ▪ The PBX / EXCHANGE LINE CONFIGURATION “Anonymous” instead of the phone number or section specifies the basic local telephone Display Name to keep the number secret. Whenever number format. possible, this should rather be configured in the INTERNATIONAL PREFIX: Prefix digits for dialling ▪...
Page 38 ▪ The INHOUSE LINES section specifies the format of internal numbers and the numbers to connect to the outside world. These settings apply to channels marked as IN-HOUSE LINES. There are individual settings for VoIP and POTS. LENGTH OF EXTENSION: Number of digits of internal ▪...
Page 39 POTS Phone Numbers (1)
Page 40 ▪ The POTS PHONE NUMBERS page is displayed only if there are POTS channels configured on the LINE INTERFACE page. ▪ There is no technical necessity to specify the POTS phone numbers. Enter the POTS phone numbers if you like to ▪...
Page 41 POTS Interface: PABX / Outside Line (1)
Page 42 POTS INTERFACE: interrupted for the MAGIC THipPro Lite to drop the OUTSIDE LINES page. call. Short interrupts are used to signal events in the network (e.g., initiate call forwarding).
Page 43 ▪ BUSY / DROP TONE: The MAGIC THipPro Lite can ▪ ENABLE EXPERT SETTINGS: Help to improve the detect if the remote station has hung up. It is audio signal on telephone lines with difficult line monitoring the audio signal for a sequence of characteristics.
Page 44 VoIP (LAN/SIP) (1)
Page 45 BACKUP SERVER: The MAGIC THipPro Lite monitors ▪ ▪ The MAGIC THipPro Lite provides up to 8 VoIP constantly if the primary SIP server is available. If channels which are completely independent from not, it switches to the backup SIP server. When the each other.
Page 46 With the public phone number. VoIP, there are several ways to transmit DTMF tones. The MAGIC THipPro Lite supports the USER AUTHENTICATION: Identifies the user account ▪ transmission via INBAND audio signal or via if a password is needed to access a SIP server.
Page 47 ▪ NAT KEEP ALIVE INTERVAL: Set the time interval at control which is not supported by MAGIC THipPro which the MAGIC THipPro Lite sends periodic Keep- Lite. (default value = 0) Alive packets to the SIP Server. Thus, routers and Typical values used for VoIP are: ▪...
Page 48 SIP server rejects the registration telegrams AS DEFAULT: Enable this settings if phones call as too soon. which announce a list of supported audio codecs but only work when the MAGIC THipPro Lite selects the first algorithm from the list. VoIP (LAN/SIP) (5)
Page 49 USE INDIVIDUAL LOCAL SIP PORT NUMBERS: ▪ Enable this setting if a SIP server requires the MAGIC THipPro Lite to use a different local SIP port for each VoIP line. ② ▪ START PORT: SIP port used for the first VoIP channel.
Page 50 Audio Interface (1)
Page 51 AES/EBU INTERFACE - CLOCK SOURCE OF EXTERNAL / CLOCK 1: Synchronize to the external ▪ DIGITAL OUTPUT: The MAGIC THipPro Lite has clock supplied through the CLOCK 1 socket on the sample rate converters only on the AES/EBU rear panel of MAGIC THipPro Lite.
Page 52 ▪ MAIN NOMINAL LEVEL OF ANALOG (XLR): Use ▪ HANDSET 1/2: Set the audio levels of the handset these parameters to adjust the level of analogue interfaces on the front panel of the MAGIC audio signals to match the level of the digital THipPro Lite.
Page 53 AES67 (1)
Page 54 ▪ Configure the technical parameters of AES67 audio over IP on the AES67 page. Find the details in the ▪ Audio over IP (AES67-DANTE-RAVENNA- LIVEWIRE) document available in the download section of our website. AES67 (2)
Page 55 LAN Interface (1)
Page 56 Assign a service (Ember+, DHD, SNMP, PC control, ▪ ...) to a VLAN on the VLAN configuration page. ▪ The MAGIC THipPro Lite Base Board has two ▪ Assign a service (Ember+, DHD, SNMP, PC control, Ethernet interfaces..) to an IP address on the corresponding The LAN 3/4 module adds two additional Ethernet configuration page of the service.
Page 57 ▪ ACCESSIBLE FROM: Select the Ethernet interface Required to resolve host names of SIP servers and and the IP address of the MAGIC THipPro Lite, to STUN servers. which the PCs should be allowed to connect. LINK TYPE: Sets the mode for crossover cable ▪...
Page 58 NTP (1)
Page 59 The MAGIC THipPro Lite can synchronise its system time to coordinated universal time (UTC) via NTP. The MAGIC THipPro Lite always tries to connect to ▪ the PRIMARY SERVER. If that server is not available it will try to retrieve the time information from the ALTERNATIVE SERVER.
Page 60 VLAN (1)
Page 61 If not done correctly the PC software VLAN: Enable or disable virtual networks globally. ▪ will lose connection the MAGIC THipPro Lite. ▪ SERVICE: All services provided by the MAGIC THipPro Lite which support VLANs are listed here.
Page 62 DHD AUDIO MATRIX (1)
Page 63 Configure the parameters for connecting the ▪ REDUNDANCY LAN INTERFACE: Select the LAN MAGIC THipPro Lite to a DHD core on the DHD interface of the MAGIC THipPro Lite which AUDIO MATRIX page. connects to the Redundancy IP Address of the DHD cores.
Page 64 Ember+ (1)
Page 65 Configure the parameters for connecting the ▪ ACTIVATE EMBER+ CONSUMER to connect the MAGIC THipPro Lite to studio equipment MAGIC THipPro Lite to one or two Ember+ supporting Ember+ on the EMBER+ page. providers. Enabling the Ember+ consumer is also required for ▪...
Page 66 PhonerSet / Remote Light (1)
Page 67 AUDIO PORT: Each PhonerSet phone establishes an ▪ Configure the parameters for connecting ▪ audio stream to the MAGIC THipPro Lite for pretalk. PhonerSet or Remote Light controllers to the Enter a unique port for each PhonerSet phone. MAGIC THipPro Lite on the PHONERSET / REMOTE (default: 5400, 5402 , 5404 , 5406 , 5408 , 5410, LIGHT page.
Page 68 Stream Quality Measurement (1)
Page 69 ▪ Configure the parameters for the stream quality ▪ The thresholds for the status LEDs can be indication on the PC software clients on the configured under QUALITY LED STATUS. STREAM QUALITY MEASUREMENT configuration PACKET LOSS >: Define the number of packet losses ▪...
Page 70 SNMP (1)
Page 71 SYSTEM DESCRIPTION: Enter a string describing ▪ ▪ THipPro Lite supports SNMPv1 and SNMPv2c. this particular MAGIC THipPro Lite. This string is part of the standard MIB. READ / TRAP COMMUNITY: Enter a string for the ▪ READ community and a string for the TRAP CONTACT: Enter a string with information about ▪...
Page 72 Note: Find the MIB files in the MIB folder inside the ▪ CATEGORY A-D ALIAS: Each Trap may be ▪ installation directory of the MAGIC THipPro Lite assigned to a category. Enter strings to describe PC software. the categories. The strings can be read by the network management station.
Page 73 Quick Dials (1)
Page 74 ▪ Configure quick dials for loading presets via the front keypad of the MAGIC THipPro Lite on the QUICK DIALS configuration page. ▪ Long press a button on the front keypad of the MAGIC THipPro Lite to load the specified Preset.
Page 76 Date and Time (1)
Page 77 ▪ In an NTP server is not available you may set the internal clock of the MAGIC THipPro Lite on the DATE AND TIME configuration page. Date and Time (2)
Page 78 Login (1)
Page 79 Protect the configuration of the MAGIC THipPro ▪ Note: If you forgot your password, you need to Lite from unauthorized access via passwords. reset the MAGIC THipPro Lite to factory settings. Configure the passwords on the LOGIN ▪ Note: The local configuration on the PC is configuration page.
Page 80: Operation Settings
MAGIC THipPro Lite Operation Settings info@avt-nbg.de www.avt-nbg.de © AVT Audio Video Technologies GmbH...
Page 81 Clients / Security (1)
Page 82 name or by its IP address used to connect to the ▪ Manage connected PC clients on the CLIENTS / system. SECURITY page. ▪ CHAT NAME: Enter a name which is used in the ▪ Only Clients specified in this list are permitted to built-in chat window.
Page 83 Mode & Audio Line (1)
Page 84 2 STUDIOS: The telephone lines of the MAGIC Pretalk simultaneously. The audio signals are THipPro Lite can be split between two studios. By mixed in the MAGIC THipPro Lite. default, the PC clients 1-4 see the first studio. The PC clients 5-8 see the second studio.
Page 85 The output audio signal can be used to monitor ▪ CHANNEL ASSIGNMENT: Assign telephone lines to ▪ audio signals of the MAGIC THipPro Lite. Further the available studios. Channels can be exclusive configuration is necessary on the MONITORING SOURCE configuration page.
Page 86 ON AIR ACCESS: Enable, if the client is allowed to ▪ put a call ON AIR. ▪ RINGING TONE: Enable, if the audio interface assigned to that client should play a ringtone if there is an incoming call. ▪ 2 STUDIO SCREENING: Enable to have the telephone lines of studio 1 and studio 2 displayed on that client.
Page 87 HOLD Signal (1)
Page 88 All AES67 / Ravenna / Dante channels ▪ RECORDED HOLD SIGNAL: An audio signal stored in ▪ ▪ START: Starts recording. the internal memory of the MAGIC THipPro Lite is STOP: Stops recording ▪ used. ▪ SAVE: Stores the file on the MAGIC THipPro Lite.
Page 89 IMPORT FROM FILE: You may import an audio file. ▪ Only the first 16 seconds of the audio file are imported. The import module supports WAVE and MP3 audio files. They are automatically converted to a mono file with 16 kHz sampling frequency. ▪...
Page 90 PhonerSet (1)
Page 91 ▪ Define which audio lines are used by the PhonerSet workplaces PHONERSET page. ▪ STUDIO / Caller Line: Define which channels are displayed in the PhonerSet app for each workplace. STUDIO N: All channels of the respective studio are ▪ available on the PhonerSet.
Page 92 Remote Light Audio Assignment (1)
Page 93 ▪ Define which audio lines are used by the clients which control the MAGIC THipPro Lite via the Remote Light Protocol. ▪ Only audio interfaces which are assigned to audio lines on the MODE & AUDIO LINE configuration page are available.
Page 94 Signal Processing (1)
Page 95 ▪ Define the signal processing parameters on the ▪ AUTOMATIC GAIN CONTROL SETTINGS (AGC) / SIGNAL PROCESSING page. EXPANDER: Define the filter parameters for AGC and expander. ▪ LINE SETTINGS: THRESHOLD: The AGC is only applied to audio ▪ AUTOMATIC GAIN CONTROL: The AGC controls the ▪...
Page 96 LINE BASIS DELAY: The echo canceller can detect ▪ VOLUME CONTROL DEFAULT VALUE: The level of ▪ and eliminate echoes with a delay of up to 120 ms. the audio signal coming from the caller can be Each telephone network has an individual minimum adjusted manually in the PC software if AGC is round-trip time for echo signals.
Page 97 ▪ VOICE DISGUISE: Define the parameters of the Voice Disguise module here. Voice Disguise can be enabled on the MODE & AUDIO LINE configuration page. PITCH: Set to UP to shift the voice to higher notes. ▪ Set to DOWN to shift the voice to lower notes. ▪...
Page 98 Monitoring Source (1)
Page 99 ▪ Define audio monitoring parameters on the MONITORING SOURCE page. ▪ The monitoring audio signal is output on the audio interface assigned to HOLD / MONITORING on the MODE & AUDIO LINE configuration page. Select the audio signals to monitor in the table: ▪...
Page 100 Auto Answer (1)
Page 101 ▪ Define how the system accepts incoming calls ▪ AUTO ANSWER DELAY: Define how long a call automatically on the AUTO ANSWER page. must ring before the system accepts the call. During that time the call can be answered ▪ AUTO ANSWER ON ALL CHANNELS: Select to manually by the user.
Page 102 Line Labels (1)
Page 103 {sipaut}: Only in VoIP mode. SIP authentication as ▪ Define the labels of all telephone channels ▪ defined on the VoIP (LAN / SIP) configuration page. displayed on the main panel of the PC software on the LINE LABELS page. ▪...
Page 104 Database (1)
Page 105 MAGIC TOUCH: This is a Microsoft Access database ▪ using the format of the discontinued MAGIC Touch ▪ The MAGIC THipPro Lite uses a Microsoft Access telephone hybrid system. database to store caller information and call MAGIC THIPPRO LITE: This is a Microsoft Access ▪...
Page 106 By default, these types are: available to all clients for read and write access. ▪ Private Find the database file “Caller.mdb” in the installation directory of the MAGIC THipPro Lite PC ▪ Mobile software. Copy the file to a location where all ▪...
Page 107 Database (4)
Page 108 NETWORK LIBRARY: Chose a network library which ▪ SQL SERVER: ▪ uses a protocol which is supported by the specified Find the SQL SERVER 2012 INSTALLATION ▪ SQL server: document in the download section of our website. DEFAULT: The driver on the Client PC choses the ▪...
Page 109 AREA CODE: The national telephone number prefix for ▪ ADD PHONE NUMBER TYPE: Click to add a phone the city in which the MAGIC THipPro Lite is located. number type to the list. Edit the parameters directly in LABEL FOR INHOUSE CALLS: This label is displayed ▪...
Page 110 ▪ OPERATION PARAMETERS: Manage access to database content. AUTO-LOCK INFO: Information about each call may ▪ be stored by the user in the info record. Set the timeout when the system locks the info record after the last editing. If an info record is locked, the user must use a new info record for entering call information.
Page 111 Night Service (1)
Page 112 ▪ Configure the Night Service mode and parameters ▪ FUNCTION: Select a mode: on the NIGHT SERVICE page. NO NIGHT SERVICE OPERATION: Night service is not ▪ available to the user. ▪ When night service is activated, all incoming calls ▪...
Page 113 ▪ TRANSFER INCOMING CALL parameters: #: Six different call forwarding destinations can be ▪ defined. ▪ PHONE NUMBERS: Define the call forwarding destinations. ▪ PHONE NUMBER ALIAS: Enter a short text describing the destination. It will be presented to the user when selecting a destination and can be used in the night service message.
Page 114 DTMF Event Labels (1)
Page 115 (0-9, *,#) on his or her phone. The information can be decoded by the MAGIC THipPro Lite. The MAGIC THipPro Lite can decode signals which ▪ are transmitted as an audio signal or via RFC2833 in VoIP mode.
Page 116 GPIO (1)
Page 117 Find the details on the available functions in the ▪ ▪ The MAGIC THipPro Lite provides 8 hardware TTLs Signalling and Control with EmBER+ document through its GPIO connector at the back. available in the download section of our website.
Page 118 ▪ If EMBER+ PROVIDER is enabled, you can configure up to 64 inputs and 64 outputs under GPIO – EMBER+ – INPUT/OUTPUT. Find the details on the available functions in the ▪ Signalling and Control with EmBER+ document available in the download section of our website. If EMBER+ CONSUMER is enabled, you can ▪...
Page 119 Ember+ Consumer Extension (1)
Page 120 ▪ The EMBER+ CONSUMER EXTENSION makes it easy to control telephone lines of the MAGIC THipPro Lite from a mixing console without using the PC software. ▪ The mixing console must act as Ember+ provider and support DHD SetLogic. Configure the workplaces on the EMBER+ ▪...
Page 121 Ember+ Dial Pad Extension (1)
Page 122 Find the dial pads in the Ember+ tree of the ▪ MAGIC THipPro Liteunder: AVT MAGIC THipPro > GPIOs > Dial Pad N Find the number entered via a dial pad in the ▪ Ember+ tree of the MAGIC THipPro Lite under: AVT MAGIC THipPro >...
Page 123: Local Settings
MAGIC THipPro Lite Local Settings info@avt-nbg.de www.avt-nbg.de © AVT Audio Video Technologies GmbH...
Page 124 Window Parameters (1)
Page 125 CUSTOM: Set a custom windows size in pixels. The ▪ Define the appearance of the PC software on the ▪ supported range is: WINDOW PARAMETERS configuration page. ▪ Width: 900 – 8000 pixels ▪ SCREEN RESOLUTION: Displays the screen ▪ Height: 280 –...
Page 126 Lite waits until the phone is picked up by the call transfer destination with the possibility to talk in Pretalk. In Hold or On Air, the MAGIC THipPro Lite hangs up as soon as the call transfer destination answers the call.
Page 127 PRETALK Streaming (1)
Page 128 The audio signal of an audio input of the PC is ▪ Capture Driver or the Default Communication streamed to the MAGIC THipPro Lite by the PC software. Device. (Check the sound settings of the operating system to see which audio interfaces The MAGIC THipPro Lite streams the audio signal of ▪...
Page 129 To open a recording in the audio editor, display plays it on the audio output if the Pretalk stream the Recordings list, click on a recording with the from the MAGIC THipPro Lite is received. right mouse button and click EDIT RECORD CALLER AND SCREENER TO A STEREO ▪...
Page 130 Chat (1)
Page 131 ▪ Define the parameters for the PC software chat on the CHAT page. ▪ The PC clients have an integrated chat function. A chat window is displayed when clicking the SHOW LISTS button in the top action bar of the main panel.
Page 132 Settings Location (1)
Page 133 The settings are saved in the user directory of the logged-in Windows account. User rights are sufficient to change the local settings. (%APPDATA%\LOCAL\AVT\MAGIC THipPro LITE) FOR ALL USERS: All users of the PC use the same ▪ settings. Windows Administrator rights are required to change the local settings.
Page 134 MAGIC THipPro Lite Setting Factory Settings info@avt-nbg.de www.avt-nbg.de © AVT Audio Video Technologies GmbH...
Page 135 The MAGIC THipPro Lite can be reset to factory settings ▪ via Front Display. ▪ The configuration of the device is reset. All files stored on the device are preserved. ▪ ▪ The configurations of all clients are preserved. If there is no password configured, the device can be ▪...
Page 136 ▪ If there is a password configured but the password is not known, the device can only be reset via front display as shown on the right. Set Factory Settings (2)
Page 137: Factory Settings
▪ The MAGIC THipPro Lite can also be reset to factory settings via the PC software. ▪ Go to MENU – ADMINISTRATION – SET FACTORY SETTINGS. Set Factory Settings (3)
Page 138: Maintenance
MAGIC THipPro Lite Maintenance info@avt-nbg.de www.avt-nbg.de © AVT Audio Video Technologies GmbH...
Page 139: Backup / Restore
Backup / Restore (1)
Page 140 After the backup was restored the PC software might lose connection to the MAGIC THipPro Lite. Enter the ▪ Presets new IP address of the MAGIC THipPro Lite in the PC software under MENU > CONTROL INTERFACE. Recorded Hold signals ▪...
Page 141 Update and Firmware Download (1)
Page 142 ▪ Find updates to the MAGIC THipPro Lite software ▪ You may also update the firmware manually via on our website avt-nbg.de in the DOWNLOADS MENU → ADMINISTRATION → FIRMWARE section under SOFTWARE. DOWNLOAD. The firmware file included in the PC software is ▪...
Page 143: Registration
Registration (1)
Page 144 ▪ Open ADMINISTRATION → REGISTRATION to check which SOFTWARE options are available in your system. ▪ ENTER PASSWORD: Adding new licences is done by entering a licence password. Contact us if you like to purchase a licence. ▪ Attach the FACTORY NUMBER of your unit which is ▪...
Page 145: System Monitor
System Monitor (1)
Page 146 100 Mbit/s, full duplex. ▪ The information is organised in sections: ▪ DHD AUDIO MATRIX: The MAGIC THipPro Lite couldn’t connect to a configured DHD core. SYSTEM ALARMS: These alarms show the status of ▪ ▪...
Page 147 TX/RX: Gross data rates of the interface in send and ▪ receive direction. The MAGIC THipPro Lite can handle PATH DELAY: Current delay to the PTP master. ▪ up to 25 MBit/s in RX direction. If the data rate is higher, check for broadcast or multicast traffic that is reaching the THipPro unintentionally.
Page 148 MAGIC THipPro Lite. optional Pretalk Streams. NUMBER: Internal port used to connect the PC client. ▪ ▪ LED: Displays whether the MAGIC THipPro Lite receives a pretalk stream from a PC software client. ▪ NAME: Client alias. ▪...
Page 149 Ravenna Streams (1)
Page 150 CHANNEL: Shows which Ravenna Tx channels of ▪ windows always on top of the screen. the MAGIC THipPro Lite are included in that stream. STREAM: The stream number as displayed in the ▪ LAN 1 /2, ERROR, WARNING: Shows if there are any ▪...
Page 151 Audio Interface Monitor (1)
Page 152 ▪ Open MENU – SYSTEM MONITOR – AUDIO ▪ PHONERSET: PhonerSet audio streams over IP. INTERFACE MONITOR to get an overview of the ▪ AES67: AES67 audio channels of the AES67 software module. audio interfaces. DANTE: Audio channels of the Dante hardware ▪...
Page 153 SIP State Monitor (1)
Page 154 ▪ Open MENU – SYSTEM MONITOR – LINE STATE MONITOR to get an overview of the VoIP telephone lines. ▪ KEEP WINDOW ON TOP: Activate to keep the windows always on top of the screen. Each telephone line is displayed in a line of the ▪...
Page 155 Record SIP Logfile (1)
Page 156 ▪ STOP LOGGING: Click to stop recording the SIP MONITOR – RECORD SIP LOGFILE to save the SIP messages. communication of the MAGIC THipPro Lite to a ▪ VIEW LOGFILE: Open the logfile in a text editor on file. the PC. Available once the logging is stopped.
Page 157: Support
Support Hotline Support-Portal Support E-Mail +49 911 2571 110 avt-nbg.zammad.com support@avt-nbg.de Support info@avt-nbg.de www.avt-nbg.de...

This manual is also suitable for:

Magic thippro pure lite

AVT MAGIC THipPro Lite Configuration Manual

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for AVT MAGIC THipPro Lite

Summary of Contents for AVT MAGIC THipPro Lite

This manual is also suitable for:

Table of Contents