Functional Description - Makita TD003G Instruction Manual

10. The contained lithium-ion batteries are subject to
the Dangerous Goods Legislation requirements.
For commercial transports e.g. by third parties,
f o r w a r d i n g a g e n t s , s p e c i a l r e q u i r e m e n t o n p a c k -
a g i n g a n d l a b e l i n g m u s t b e o b s e r v e d .
F o r p r e p a r a t i o n o f t h e i t e m
i n g a n e x p e r t f o r h a z a r d o u s m a t e r i a l i s r e q u i r e d .
Please also observe possibly more detailed
n a t i o n a l r e g u l a t i o n s .
Tape or mask o open contacts and pack up the
battery in such a manner that it cannot move
a r o u n d i n t h e p a c k a g i n g .
W hen disposing the battery cartridge, remove
11.
it from the tool and dispose of it in a safe
place. Follo w your local regulations relating to
disposal of battery.
12. Use the batteries only w ith the products
speci ed by Makita. I n s t a l l i n g t h e b a t t e r i e s t o
non-compliant products may result in a fire, exces-
sive heat, explosion, or leak of electrolyte.
1 3 . If the tool is not used for a long period of time,
the battery must be removed from the tool.
1 4 . During and after use, the battery cartridge may
take on heat w hich can cause burns or lo w
temperature burns. Pay attention to the han-
dling of hot battery cartridges.
15. Do not touch the terminal of the tool imme-
diately after use as it may get hot enough to
cause burns.
1 6 . Do not allo w chips, dust, or soil stuck into the
terminals, holes, and grooves of the battery
cartridge. It may cause heating, catching fire,
burst and malfunction of the tool or battery car-
tridge, resulting in burns or personal injury.
17. Unless the tool supports the use near
high-voltage electrical po w er lines, do not use
the battery cartridge near a high-voltage elec-
trical po w er lines. It may result in a malfunction
or breakdown of the tool or battery cartridge.
18. Keep the battery a w ay from children.
SAVE THESE INSTRUCTIONS.
CAUTION:
Only use genuine Makita batteries.
U s e o f n o n - g e n u i n e M a k i t a b a t t e r i e s , o r b a t t e r i e s t h a t
have been altered, may result in the battery bursting
causing fires, personal injury and damage. It will
also void the Makita warranty for the Makita tool and
c h a r g e r .
Tips for maintaining maximum
battery life
Charge the battery cartridge before completely
1.
discharged. Al w ays stop tool operation and
charge the battery cartridge w hen you notice
less tool po w er.
2. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
Charge the battery cartridge w ith room tempera-
3 .
ture at 10 ° C - 40 ° C (50 ° F - 104 ° F). Let a hot
battery cartridge cool do w n before charging it.
W hen not using the battery cartridge, remove
4 .
it from the tool or the charger.
5. Charge the battery cartridge if you do not use
it for a long period (more than six months).
b e i n g s h i p p e d , c o n s u l t -
7 ENGLISH

FUNCTIONAL DESCRIPTION

CAUTION:
Al w ays be sure that the tool is
switched o and the battery cartridge is removed
before adjusting or checking function on the tool.
Installing or removing battery cartridge
CAUTION:
Always switch o the tool before
installing or removing of the battery cartridge.
CAUTION:
Hold the tool and the battery car-
tridge rmly when installing or removing battery
cartridge. Failure to hold the tool and the battery
cartridge firmly may cause them to slip o your hands
and result in damage to the tool and battery cartridge
and a personal injury.
To remove the battery cartridge, slide it from the tool
w h i l e s l i d i n g t h e b u t t o n o n t h e f r o n t o f t h e c a r t r i d g e .
Fig.1: 1. R e d i n d i c a t o r 2. B u t t o n 3. Battery cartridge
To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator as
shown in the figure, it is not locked completely.
CAUTION:
Al w ays install the battery cartridge
fully until the red indicator cannot be seen. I f n o t ,
it may accidentally fall out of the tool, causing injury to
you or someone around you.
CAUTION:
Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is
not being inserted correctly.
Indicating the remaining battery capacity
Press the check button on the battery cartridge to indi-
cate the remaining battery capacity. The indicator lamps
l i g h t u p f o r a f e w s e c o n d s .
Fig.2: 1. I n d i c a t o r l a m p s 2. C h e c k b u t t o n
Indicator lamps
Lighted O
Remaining
capacity
Blinking
75% t o 100%
50% t o 75%
25% t o 50%
0% t o 25%
C h a r g e t h e
battery.
The battery
may have
m a l f u n c t i o n e d .