Makita TD003G Instruction Manual page 10

Application mode
(Impact force grade
displayed on panel)
1 ( S o f t )
T m o d e *
: T h e l a m p i s o n .
* W h e n t h e t o o l r o t a t e s c o u n t e r c l o c k w i s e , t h e i m p a c t p e r m i n u t e i s t h e s a m e a s i n 4 ( m a x ) m o d e , 4 , 100 m i n
NOTE: When using T mode, the timing to stop the driving varies depending on the type of the screw and material
t o b e d r i v e n . M a k e a t e s t d r i v i n g b e f o r e u s i n g t h i s m o d e .
NOTE: W h e n n o n e o f t h e l a m p o n t h e p a n e l i s l i t , p u l l t h e s w i t c h t r i g g e r o n c e b e f o r e p r e s s i n g t h e b u t t o n
b u t t o n .
NOTE: All lamps on the switch panel go out when the tool is turned o to save the battery power. The impact force
grade can be checked by pulling the switch trigger to the extent that the tool does not operate.
ASSEMBLY
CAUTION:
Al w ays be sure that the tool is
switched o and the battery cartridge is removed
before carrying out any w ork on the tool.
Installing or removing driver bit/
socket bit
Use only driver bit/socket bit that has inserting portion
shown in the figure. Do not use any other driver bit/
s o c k e t b i t .
Fig.9
For tool w ith shallo w driver bit hole
A= 12m m
B = 9 m m
For tool w ith deep driver bit hole
A= 17m m
B = 14 m m
A= 12m m
B = 9 m m
Maximum blo w s
-1
1, 4 00 m i n ( / m i n ) T i g h t e n i n g w i t h l e s s f o r c e t o a v o i d
s c r e w t h r e a d b r e a k a g e .
– Dr i v i n g s e l f -d r i l l i n g s c r e w s t o a t h i n
( T h e t o o l s t o p s r o t a t i n g metal plate with good finish.
s o o n a f t e r i m p a c t s t a r t s .)
Use only these types of driver
b i t s . F o l l o w t h e p r o c e d u r e
1. ( N o t e ) B i t -p i e c e i s n o t
necessary.
To install these types of driver
b i t s , f o l l o w t h e p r o c e d u r e 1.
To install these types of driver
b i t s , f o l l o w t h e p r o c e d u r e 2.
(Note) Bit-piece is necessary
f o r i n s t a l l i n g t h e b i t .
Purpose
Procedure 1
For tool w ith one-touch type sleeve
T o i n s t a l l t h e d r i v e r b i t , i n s e r t t h e d r i v e r b i t i n t o t h e
s l e e v e a s f a r a s i t w i l l g o .
Fig.10: 1. D r i v e r b i t 2. S l e e v e
Procedure 2
I n a d d i t i o n t o Procedure 1 , i n s e r t t h e b i t - p i e c e i n t o t h e
s l e e v e w i t h i t s p o i n t e d e n d f a c i n g i n .
Fig.11: 1. D r i v e r b i t 2. B i t - p i e c e 3. S l e e v e
T o r e m o v e t h e d r i v e r b i t , p u l l t h e s l e e v e i n t h e d i r e c t i o n
o f t h e a r r o w a n d p u l l t h e d r i v e r b i t o u t .
Fig.12: 1. D r i v e r b i t 2. S l e e v e
NOTE: I f t h e d r i v e r b i t i s n o t i n s e r t e d d e e p e n o u g h
i n t o t h e s l e e v e , t h e s l e e v e w i l l n o t r e t u r n t o i t s o r i g i n a l
p o s i t i o n a n d t h e d r i v e r b i t w i l l n o t b e s e c u r e d . I n t h i s
case, try re-inserting the bit according to the instruc-
t i o n s a b o v e .
NOTE: When it is di cult to insert the driver bit, pull
t h e s l e e v e a n d i n s e r t i t i n t o t h e s l e e v e a s f a r a s i t w i l l
g o .
NOTE: A f t e r i n s e r t i n g t h e d r i v e r b i t , m a k e s u r e t h a t i t
is firmly secured. If it comes out, do not use it.
10 ENGLISH
Example of application
T i g h t e n i n g s a s h s c r e w s o r s m a l l
s c r e w s s u c h a s M 6 .
T i g h t e n i n g s e l f -d r i l l i n g s c r e w s .
-1
( / m i n ) .
o r