S+S Regeltechnik RYMASKON 200-Modbus User Manual page 35

®
RYMASKON 200-Modbus
Modbus Slave User Manual
Register Name
config_display_
value_13
config_display_
value_14
config_display_
value_15
Table 27: Display Value Configuration
© S+S REGELTECHNIK GMBH | THURN-UND-TAXIS-STR.22 | 90411 NÜRNBERG | GERMANY | FON +49(0)911 519470
Register
Address
15 14 13
282 unit_modbus
0x011A [0x0]
283
VSA VEU DSSA
0x011B [0] [0] [0]
284 unit_modbus
0x011C [0x0]
285
VSA VEU DSSA
[0] [0] [0]
0x011D
286 unit_modbus
0x011E [0x0]
287
VSA VEU DSSA
[0] [0] [0]
0x011F
These registers hold the configuration of the 16 display values.
semantic_meaning:
is used to provide information about the semantic meaning and the source of
the value. For further information please see Table 29 on Page 38.
CAL:
if set to '1' the corresponding offset_value can be edited in
CALIBRATION-mode (only capable if DSEU or DSSA is set to '1')
unit:
defines a unit with which the corresponding display value appears on the
LCD
unit_modbus:
defines a unit that the corresponding display value register appeare on
Modbus
!!! For both, unit and unit_modbus the following values are possible:
0x0 0x1 0x2 0x3
no
°C °F cfm
unit
Bits 0-11 of the higher address of each configuration register indicate the symbols that are displayed along
with the corresponding display value.
DSEU: Display Source for End User
DSSA: Diplay Source for System Administrator
These two bits define if the value displayed is taken from a display_value register at address 64 to 79 (see
Table 11 on Page 22) or from a sensor_value register at address 48 to 56 (see Table 10 on Page 21).
The following states are valid:
0 – defines that the value is taken from a display_value register that has to be set via modbus.
1 – defines that the value is taken from a sensor_value (+ offset_value) register that is automatically
updated with the current sensor value.
VEU: Visible for End User
VSA: Visible for System Administrator
These two bits define if the display value is visible for the end user and/or the system administrator.
If set to '1' the value will be visible.
Table 30
!!! See on Page 40 for example configurations of display values or set points.
Bit Position
12 11 10 9 8
unit
[0x0]
DSEU
[0]
[0] [0]
[0] [0]
unit
[0x0]
DSEU
[0]
[0] [0]
[0] [0]
unit
[0x0]
DSEU
[0]
[0] [0] [0] [0]
0x4 0x5 0x6 0x7
l/s m³/h Pa inWC V
Page 35 of 55
7 6 5 4 3
semantic_meaning
CAL
[0]
[0x00]
[0] [0] [0] [0]
[0]
semantic_meaning
CAL
[0]
[0x00]
[0] [0] [0] [0]
[0]
semantic_meaning
CAL
[0] [0x00]
[0] [0] [0] [0] [0]
0x8 0x9 0xA 0xB 0xC
% %RH ppm °F dec.
2 1 0
[0] [0] [0]
[0] [0] [0]
[0] [0] [0]
|www.SplusS.de