SpeedyBee F405 V3 BLS 50A User Manual

Hide thumbs Also See for F405 V3 BLS 50A:

Advertisement

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the F405 V3 BLS 50A and is the answer not in the manual?

Questions and answers

Summary of Contents for SpeedyBee F405 V3 BLS 50A

  • Page 1: Table Of Contents

    (Click on any section to jump) Part 1 - OverView Specs Overview Dimensions Package FC & ESC Connection Part 2 - SpeedyBee F405 V3 Flight Controller Layout FC’s Peripheral Connection App & FC Configuration FC Firmware Update Specifications Part 3 - SpeedyBee BLS 50A 4-in-1 ESC Layout Connection with Motors &...
  • Page 2: Part 1 - Overview Specs Overview

    Part 1 - OverView Specs Overview 1/14 SpeedyBee F405 V3 BLS 50A 30x30 Stack Product Name SpeedyBee F405 V3 Flight Controller SpeedyBee BLS 50A 4-in-1 ESC Supported. For FC & ESC parameter settings Bluetooth NOT Supported Wireless FC Firmware Flashing...
  • Page 3: Dimensions

    Dimensions 2/14 1.6mm 39.4mm 1.6mm 44mm 7.8mm 30.5mm 6.1mm 30.5mm 16.1mm...
  • Page 4: Package

    3/14 Package Option 1 - SpeedyBee F405 V3 50A 30x30 Stack SpeedyBee F405 V3 Flight Controller x 1 SpeedyBee BLS 50A 4-in-1 ESC x 1 35V 1500uF Low ESR Capacitor x 1 M3 Nylon Nut x 5 M3 silicone O Ring x 5 M3*8mm Silicone Grommets(for FC) x 5 M3*8.1mm Silicone Grommets(for ESC) x 5...
  • Page 5: Fc & Esc Connection

    FC & ESC Connection 4/14 Use the 8-pin cable in the package to connect the FC and the ESC. Or solder 8 wires directly to the 8 pads on each end. Method 1 - Using 8-pin cable Use any end of the 8-pin JST cable to connect the FC to the ESC. F7 V3 Flight Controller BL32 50A 4-in-1 ESC Method 2 - Direct soldering...
  • Page 6: Part 2 - Speedybee F405 V3 Flight Controller

    LED strips connected to LED1-LED4 pads on the corners. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by the Betaflight firmware.
  • Page 7: Fc's Peripheral Connection

    FC’s Peripheral Connection 6/14 PPM Receiver Reciever 5-36V 5-36V SBUS 5-36V Video Video Video G/TX Menu Menu M/RX CH2 RX CH1 TX Crossfire Nano Rx SIGNAL SERVO LED Strip Buzzer Analog VTX DJI Air Unit...
  • Page 8: App & Fc Configuration

    App & FC Configuration 7/14 Get the SpeedyBee App Search ‘SpeedyBee’ on Google Play or App Store. Or download the Android .apk file on our website: https://www.speedybee.com/download. FC Configuration...
  • Page 9: Fc Firmware Update

    FC Firmware Update 8/14 SpeedyBee F405 V3 flight controller does not support wireless firmware flashing, so please flash firmware for it on your PC following the steps below: ① Connect the flight controller to the PC with a USB cable ② Open Betafight/Emuflight/INAV configurator on your PC. Take Betaflight configurator as an example, go to the ‘Firmware Flashing’...
  • Page 10: Specifications

    Yes(CC pad on the front side) Current Sensor Input Supported. For SpeedyBee BLS 50A ESC, please set scale = 386 and Offset = 0. 3S - 6S Lipo(Through G, BAT pins/pads from the 8-pin connector or 8-pads on the Power Input...
  • Page 11: Part 3 - Speedybee Bls 50A 4-In-1 Esc Layout

    Part 3 - SpeedyBee BLS 50A 4-in-1 ESC Layout 10/14 Driver chips MOTOR 4 MOTOR 2 MOTOR 1 MOTOR 3 Capacitor pin Capacitor pin hole(GND) hole(BAT+) BAT- BAT+ 8pin connector(to FC) MCU(BB21) TVS Diode...
  • Page 12: Connection With Motors & Power Cable

    Connection with Motors & Power Cable 11/14 Motor 4 Motor 2 Motor 3 Motor 1 1500uF Low ESR Capacitor XT60 Power Cable Note : In order to prevent the stack from being burnt out by voltage spikes on powering up, it is strongly recommended to use the Low ESR capacitor in the package.
  • Page 13: Esc Configuration

    ESC Configuration 12/14 If you’d like to use a PC configurator, we recommend the ESC Configurator.
  • Page 14: Esc Firmware Update

    ESC Firmware Update 13/14 We recommend using the ESC Configurator on your PC to update firmware for this ESC. Please make sure to select ‘JH-50’ as the ESC type for either BLHeli_S or Bluejay.
  • Page 15: Specifications

    Specifications 14/14 Product Name SpeedyBee BLS 50A 30x30 4-in-1 ESC BLHeli_S JH50 Firmware Wireless Configuration Full Configuration Supported in the SpeedyBee app https://esc-configurator.com/ PC Configurator Download Link Continuous Current 50A * 4 Burst Current 55A(5S) TVS Protective diode External Capacitor...

Table of Contents

Save PDF