Mackie d8B V5.1 Owner's Manual page 180

D8B
Button
Number D8B Button Mapped HUI Button
Fader 17-24 Fader 1-8
Channel V-Pot
Channel V-Pot 1-8
17-24
Mute 17-24 Mute 1-8
Solo 17-24 Solo 1-8
Select 17-24 Select 1-8
Record Ready
Record Ready 1-8
17-24
Assign 17-24 VSel 1-8
Alt+Assign 17-
Insert 1-8
24
Write 17-24 Auto 1-8
1 Level to Tape Aux Mute
2 Digital Trim Shift (flip)
3 Aux 1 Send A
4 Aux 2 Send B
5 Aux 3 Send C
6 Aux 4 Send D
7 Aux 5 Send E
8 Aux 7 Rec Ready All
9 Aux 9-10 Bank Left
10 Aux 11-12 Bank Right
11 Aux 9-10 Pan Channel Left
12 Aux 11-12 Pan Channel Right
13 Pan Pan
14 Shift
Shift + Masters N/A
D8B VFD Display
D8B VFD V-Pots
Alt+Right D8B
Scroll
VFD V-Pot
D8B VFD Select
Buttons
Previous / Next N/A
15 On Assign
16 Setup Compare
17 Memory A Bypass
18 Memory B Insert
19 EQ Window Transport
20 Gate Window ALT
21 Compressor Window Edit
22 Plug-ins Window Status
23 Load Patch Window Mix
24 Save Patch Window Mem Loc
25 Assign Bus 2 Auto Enable Send
26 Assign Bus 3 Auto Enable Plug-in
Auto Enable Send
27 Assign Bus 4
Mute
28 Assign Bus 5 Auto Mode Read
29 Assign Bus 7 Auto Mode Latch
30 Assign Bus 8 Auto Mode Write
31 Assign L-R Shift/Add
Assign Route To
32 Save
Tape
Automation
33 Auto Mode Off
Bypass
Automation
34 Auto Enable Fader
Faders
D8B Manual • Appendices • page 174
D8B v5.1 B445 HUI Layer Control Mapping
For DP3.1
16220 Woodinville Redmond Rd. NE Woodinville, WA 98072
Tel: 800-258-6883 Fax: 425-806-6312 e-mail: techmail@mackie.com
Last Updated: 2/07/03
Global General HUI Layer
Mode Comments DP3.1 Function
N Move corresponding DP3 channel Fader.
N Move corresponding DP3 channel Pan or Send Level
Mute corresponding DP3 channel
N
N Solo corresponding DP3 channel
N Select corresponding DP3 channel
N Record Arm corresponding DP3 channel
Toggle Pre/Post of corresponding PT channel Send for selected Aux 1-5. If Level To Tape (HUI Aux Mute) is lit,
N
then it will toggle the mute status of the corresponding PT channel send for the selected Aux 1-5.
N
Select corresponding DP3 channel for Insert Editing in VFD
N Use in conjunction with Auto Mode values to set automation mode for corresponding DP3 Channel.
N
When lit, assign (V-Sel) toggles the mute status of the selected Aux. When not lit, V-Sel will toggle the selected Aux Pre/Post.
N N/A
N Enables control of DP3 Mixing Board Aux 1 by HUI layer V-Pots
N Enables control of DP3 Mixing Board Aux 2 by HUI layer V-Pots
Enables control of DP3 Mixing Board Aux 3 by HUI layer V-Pots
N
N
Enables control of DP3 Mixing Board Aux 4 by HUI layer V-Pots
N N/A
N
N/A
N
Shifts HUI layer to left by 8 to view previous 8 faders
N
Shifts HUI layer to right by 8 to view next 8 faders
N Shifts HUI layer to left by 1 to view previous fader
N Shifts HUI layer to right by 1 to view next fader
N
Enables control of VST channel settings Pan on HUI layer V-Pots
N N/A
Go to HUI Layer on
Go to HUI layer on D8B
Y
D8B
N Displays Plug-in/Insert settings for selected Insert Channel. There are two main views: Plug-in Edit View and Insert Assign view.
N Changes the assigned Plug-in, chooses a Plug-in Preset, or adjusts a plug-in parameter listed in bottom line of VFD.
N Scroll to next/previous parameter of plug-in parameters in Plug-in Edit View. Scroll to next/previous insert in Insert Assign View.
N Select Insert Slot for Editing in Insert Assign View. Selected Insert has Arrows pointing to the Slot.
N Change between normal HUI VFD mode and channel HUI VFD Mode. See note below.
Toggles function of VFD V-Pots in Insert Assign view. When not lit, V-Pots select Plug-in for their corresponding slot.
N
When lit, V-Pots select preset for their corresponding plug-in.
N
N/A
N Toggles bypass of selected plug-in
N Toggles Plug-in Edit Mode for selected plug-in
N Bring to front Control Panel Window (Transport)
N Open Insert Window
N
Open Sequence Editor Window
N Open Audio Monitor Window
N Open Mixing Board Window
N
Open Markers Window
N Toggles Send Level Automation Enable in DP3 Automation Setup window
N Toggles Effect Bypass and Effect Parameter Automation Enables in DP3 Automation Setup window
N Toggles Send Mute Automation Enable in DP3 Automation Setup window
Hold and Press a channel Write (HUI Auto) button to enable automation playback on the corresponding DP3 channel
N
Hold and Press a channel Write (HUI Auto) button to enable automation playback and recording on the corresponding
N
DP3 channel, and to put the channel into Latch automation mode.
Hold and press a channel Write (HUI Auto) button to enable automation playback and recording on the corresponding
N
DP3 channel, and to put the channel into Overwrite automation mode.
N
Shifts to second function of some buttons. Used to select multiple values of some parameters.
Press twice to save the open DP3 session
N
Hold and press a channel Write (HUI Auto) button to disable automation playback and recording on the corresponding
N
DP3 channel, and to put the channel into Touch automation mode.
N Toggles Audio Volume and MIDI Volume Automation Enables in DP3 Automation Setup window