Subscribe to Our Youtube Channel
Related Manuals for Vertiv NetSure +24V Battery Tray Kit
Summary of Contents for Vertiv NetSure +24V Battery Tray Kit
- Page 1 NetSure™ +24V Battery Tray Kit – 23” Installation Manual Specification Number: 588810200SK001...
- Page 2 The information contained in this document is subject to change without notice and may not be suitable for all applications. While every precaution has been taken to ensure the accuracy and completeness of this document, Vertiv assumes no responsibility and disclaims all liability for damages resulting from use of this information or for any errors or omissions.
-
Page 3: Table Of Contents
Vertiv™ NetSure™ +24V Battery Tray Kit Installation Manual TABLE OF CONTENTS Admonishments Used in this Document ..........................iv Important Safety Instructions ..............................v Safety Admonishments Definitions ............................................v Safety and Regulatory Statements ............................................v Déclarations de Sécurité et de Réglementation ......................................v 1 Description ....................................1... -
Page 4: Admonishments Used In This Document
Vertiv™ NetSure™ +24V Battery Tray Kit Installation Manual Admonishments Used in this Document will likely DANGER! Warns of a hazard the reader be exposed to that will result in death or serious injury if not avoided. (ANSI, OSHA) could WARNING! Warns of a potential hazard the reader... -
Page 5: Important Safety Instructions
Vertiv™ NetSure™ +24V Battery Tray Kit Installation Manual Important Safety Instructions Safety Admonishments Definitions Definitions of the safety admonishments used in this document are listed under “Admonishments Used in this Document” on page iv. Safety and Regulatory Statements Refer to Section 4154 (provided with your customer documentation) for Safety and Regulatory Statements. - Page 6 Vertiv™ NetSure™ +24V Battery Tray Kit Installation Manual This page intentionally left blank. Proprietary and Confidential © 2022 Vertiv Group Corp.
-
Page 7: Description
This document provides installation practice for the 588810200SK001 Battery Tray Kit. The Vertiv™ NetSure™ +24V Battery Tray Kit, part number 588810200SK001, provides a 22" deep battery tray for 23" wide relay rack. The battery tray holds four (4) 12V front terminal valve regulated lead acid (VRLA) batteries. Battery cabling is provided and shall be connected to the system’s main battery busbars. -
Page 8: Installation Procedures
Vertiv™ NetSure™ +24V Battery Tray Kit Installation Manual 2 Installation Procedures 2.1 Mounting the Battery Tray Procedure To install a Battery Tray, perform the procedure in Figure 2.1. Figure 2.1 Mounting and Securing the 588810200SK001 Battery Tray onto the Rack 1. -
Page 9: Installing The Circuit Breakers
Vertiv™ NetSure™ +24V Battery Tray Kit Installation Manual 2.2 Installing the Circuit Breakers Procedure Remove the cover from the battery disconnect circuit breaker assembly. Secure the battery disconnect circuit breaker assembly to the battery tray using 6-32 x 1/2” screws and 6-32 KEPS nuts (2-places). -
Page 10: Installing And Connecting Batteries In The Battery Tray
Vertiv™ NetSure™ +24V Battery Tray Kit Installation Manual 3 Installing and Connecting Batteries in the Battery Tray 3.1 Important Safety Instructions DANGER! Adhere to the “Important Safety Instructions” presented at the front of this document. 3.2 Wiring to the Battery Tray Procedure Refer to the wiring diagram provided in Figure 3.1 and wire the battery tray for your application. -
Page 11: Installing And Connecting Batteries
Vertiv™ NetSure™ +24V Battery Tray Kit Installation Manual 3.3 Installing and Connecting Batteries Procedure NOTE! Figure 3.2 Refer to as this procedure is performed. If Battery Trays are Equipped With Circuit Breakers: Turn OFF the Battery Disconnect circuit breakers located on all battery trays. - Page 12 Vertiv™ NetSure™ +24V Battery Tray Kit Installation Manual Figure 3.2 Battery Tray Battery Installation Details Connect NEG (-) Connect Link Furnished Connect POS (+) Connect Link Furnished Battery Cable Battery Cable with Battery to these with Battery to these to this Terminal...
- Page 13 Vertiv™ NetSure™ +24V Battery Tray Kit Installation Manual Figure 3.3 Cable Routing - Battery Tray with Circuit Breakers Routes up to Routes up to (-) Input Battery Busbar (+) Input Battery Busbar (Rear of Cabinet) (Rear o f Cabinet) Wire marked per...
-
Page 14: Alarm Jumper Routing
NOTE! For the Vertiv™ Vortex™ or Vertiv™ NetSure™ 700 system, this is PIN 11 of TB1 (System Fuse Alarm Input) on the Interconnect/Inhibit Card on the right side of the base of the power system distribution cabinet. For Vertiv™ NetSure™ 710 system this is PIN 1 of TB1 (Battery Tray FA) on the System Interface circuit card inside the distribution cabinet. - Page 15 Vertiv™ NetSure™ +24V Battery Tray Kit Installation Manual Figure 4.1 Alarm Jumper Routing 22 GA jumper Proprietary and Confidential © 2022 Vertiv Group Corp.
- Page 16 Vertiv™ NetSure™ +24V Battery Tray Kit Installation Manual This page intentionally left blank. Proprietary and Confidential © 2022 Vertiv Group Corp.
- Page 17 Vertiv™ NetSure™ +24V Battery Tray Kit Installation Manual Connect with Vertiv on Social Media https://www.facebook.com/vertivI https://www.instagram.com/vertiv/ https://www.linkedin.com/company/vertiv/ https://www.twitter.com/vertiv/ Proprietary and Confidential © 2022 Vertiv Group Corp.
- Page 18 Vertiv.com | Vertiv Headquarters, 1050 Dearborn Drive, Columbus, OH, 43085, USA © 2022 Vertiv Group Corp. All rights reserved. Vertiv™ and the Vertiv logo are trademarks or registered trademarks of Vertiv Group Corp. All other names and logos referred to are trade names, trademarks or registered trademarks of their respective owners. While every precaution has been taken to ensure accuracy and completeness here, Vertiv Group Corp.
Need help?
Do you have a question about the NetSure +24V Battery Tray Kit and is the answer not in the manual?
Questions and answers