文件名称:售后维修服务手册(6M181/6E181/6M182/6E182 方案) Document: After-sales Maintenance Service Manual(6M181/6E181/6M182/6E182 Scheme) 6M181/6E181/6M182/6E182 Scheme Adjustment of Factory Mode Press Menu to enter into the menu interface, and then press 8202 to enter into Factory menu. Primary Menu Secondary Menu Value, Notes ADC ADJUST MODE VGA(RGB),YPbPr(SD,HD)selection R-GAIN G-GAIN...
Page 15
文件名称:售后维修服务手册(6M181/6E181/6M182/6E182 方案) Document: After-sales Maintenance Service Manual(6M181/6E181/6M182/6E182 Scheme) Power-up mode (power-on upon powering up, power-off upon powering up, restore Power Mode to the previous status upon powering up) Aging Burning ON/OFF. VD&VIF-NoStrand1 VD&VIF-NoStrand2 VD&VIF parameter adjustment VD&VIF-NoStrand3 set factory TV channels CH Table1 CH Table2 set factory TV channels...
Page 16
MST6M182/MST6E182 software upgrades (After Service) 1、Software upgrade tools and materials * Personal computer (WINDOWS XP system,USB2.0) * AC100~240V power supply and power cord * ISP burning board * ISP burning board driver *ISP Tool V4.5.2.8.SZ.exe *VGA wire USB flash disk(2.0 version,Capacity not more than 2G) * Mainboard software 2、Preparatory work before the upgrade Recorded the white balance data of VGA/YPBPR signal source in factory menu before upgrading(FLASH initialization...
Page 17
has been inserted into, or change another U disk and try again. ③. Display percentage progress prompts and about 10 seconds later, the machine black screen and restart automatically, means that the machine complete the upgrade process, turn off the machine first, then pull out the U disk. Press 升...
Page 18
following instructions. (1). Connect the ISP burning board and TV VGA port with VGA cable. (2). Insert the Mstar USB Tool into the USB port of your PC. The PC can recognize the new device. You can choose to install it in the list, or choose to install at a specified directory and specify the path to the drive file. See the figure below:...
Page 19
(3) When PC finds the drive file, it will give the prompts as in the figure below during the installation process. Please click “Continue" to go ahead. The system will go through three drive installation processes, including Mstar USB Debug Tool A, Mstar USB Debug Tool B, and Mstar USB SerialPort.
Page 20
(3). Click Connect button to connect, if it prompts “Device Type is GD25Q32”, means that normal connecting; if it prompts “Can't find the Device Type!” means that there is poor connecting, please have a check. Abnormal (4). Click "Read" button in tool bar, then click "Read" to load current software. (5).
Page 21
Then click “RUN”button to burn software. When display“PASS” ,means that it succeed,then burn EDID according to the following instructions.
Page 22
5、Use ISP way to upgrade(when used USB way to upgrade, it coundn't erase the original EDID and HDCP KEY on mainboard, so we require customer use this way to upgrade first.), when you selected "ALL Chip" under "Erase Device" option during upgrading, the TV mainboard must burn EDID and HDCP KEY. The buring tools and materials for HDCP KEY and EDID: * Personal computer (WINDOWS XP system,USB2.0)...
Page 23
Please click to load current software. If prompts “Device Type is GD25Q32” means that normal connect; if prompts “Can’t find the Device Type!” means that there is poor connecting, please have a check.
Page 24
Abnormal If prompts “Device Type is GD25Q32” means that normal connect; if prompts “Can’t find the Device Type!” means that there is poor connecting, please have a check. (3). Click HdcpEdid button in main menu bar to set corresponding settings according to the following instructions: Need to burn HDCP KEY, please select and load current KEY documents, in KEY address bar input "0 X3B0000"...
Page 25
interface. Don't selet, if mainboard have burned correct KEY or EDID. (4).In burning main interface, select corresponding function, click Setup button Erase Device, Don't selet, if mainboard have burned correct KEY or EDID. to enter to Erase Block Setting menu, click Clear All to clear,click drop-down list in Global Offset Address, select"OX00000000,Bank 00",in address list select "0X3B0000", check address settings and click "OK"...
Page 26
(5).In burning interface, click "Run" to burn. Burning prompt bar will prompt burning process related information, about 12 seconds appear "Pass", and there is no longer any character rolling in prompt bar, means that is burning successfully. (6). Shut down the power of jig, pull out the burning wire to complete burning operation. It not allow pulling out the wires during burning process.
Page 27
(1). Power to the machine, press MENU button on the remote control then press 8202 number keys and then will popping the factory menu automatically, press the remote control up/down cursor keys to move to the "Reset" option press OK key to implement. After about 5 seconds latter the machine implement clear command automatically.
Page 28
Change R-GAIN/G-GAIN/B-GAIN value and R-OFFSET/G-OFFSET/B-OFFSET value to the value before the upgrade under the YPbPr(SD/HD) mode (5). In the ADC ADJUST item, press OK key to enter the next level menu, move the cursor to the MODE item, press the left/right keys tomove cursor select the YPbPr(HD)item, change the R-GAIN/G-GAIN/B-GAIN value and R-OFFSET/G-OFFSET/B-OFFSET value of the machine after the upgrade to the value before the upgrade.
Page 33
ITBC0101 v5.0 Model 32L31F\32L41F Document No. Version Back Cover Processing-1 Station Name Section/Serial No. Preprocessing 01 2012-11-1 2012-11-1 Panel K320WD1 series Effective from Date Updated Part Number Amount Descriptions Operations and Requirements Diagram Tool Parameters 7002-32L31F-C4B00013 32L31F\32L41F black back cover Fit button array to back cover properly as illustrated.
Page 34
ITBC0102 v5.0 Model 32L31F\32L41F Document No. Version Back Cover Processing-2 Station Name Section/Serial No. Preprocessing 02 2012-11-1 2012-11-1 Panel K320WD1 series Effective from Date Updated Part Number Amount Descriptions Operations and Requirements Diagram Tool Parameters Ф4×10mm round-head flat-tail nickel-plated tapping 7B11-041082-30105113 Fit the two speakers to back cover properly.
Page 35
ITBC0103 v5.0 Model 32L31F\32L41F Document No. Version Adhesive Film Sticking Station Name Section/Serial No. Preprocessing 03 2012-11-1 2012-11-1 Panel K320WD1 series Effective from Date Updated Part Number Amount Descriptions Operations and Requirements Diagram Tool Parameters T9 side interface adhesive film of mainboard Stick side interface adhesive film on side of back cover properly.
Page 36
ITBC0104 v5.0 Model 32L31F\32L41F Document No. Version Base Processing Station Name Section/Serial No. Preprocessing 04 2012-11-1 2012-11-1 Panel K320WD1 series Effective from Date Updated Part Number Amount Descriptions Operations and Requirements Diagram Tool Parameters 7003-32L31D-1U700001 32L31D glossy black base(ellipse) Put the base on table and check if it looks fine. Figure 1 Φ20.0*2.5mm rubber pad(with 3M gummed paper) Stick 4PCS rubber pad on the base as illustrated.
Page 37
ITBC0201 v5.0 Model 32L31F\32L41F Document No. Version Display Screen Placement Station Name Section/Serial No. Unit Assembly 01 2012-11-1 2012-11-1 Panel K320WD1 series Effective from Date Updated Part Number Amount Descriptions Operations and Requirements Diagram Tool Parameters 7422-320LGK-33000201-F 32″TFT KTC K320WD1-BA280 LED panel Remove its protective packaging and check if it looks fine.
Page 38
ITBC0202 v5.0 Model 32L31F\32L41F Document No. Version Light Pipe Installation Station Name Section/Serial No. Unit Assembly 02 2012-11-1 2012-11-1 Panel K320WD1 series Effective from Date Updated Part Number Amount Descriptions Operations and Requirements Diagram Tool Parameters 7373-000000-10000011 Fragile label 38×14mm Mark the fragile label and stick it on panel back as illustrated.
Page 39
ITBC0203 v5.0 Model 32L31F\32L41F Document No. Version LVDS Wire Insertion Station Name Section/Serial No. Unit Assembly 03 2012-11-1 2012-11-1 Panel K320WD1 series Effective from Date Updated Part Number Amount Descriptions Operations and Requirements Diagram Tool Parameters 0.13mm×20mm×50m viscose paper(3M8915) 7912-712500-020R1311 Insert panel end of LVDS wire to drive board.
Page 40
ITBC0204 v5.0 Model 32L31F\32L41F Document No. Version Hexagonal Screw Locking Station Name Section/Serial No. Unit Assembly 04 2012-11-1 2012-11-1 Panel K320WD1 series Effective from Date Updated Part Number Amount Descriptions Operations and Requirements Diagram Tool Parameters Φ3×2.5×6mm hexagonal screw 7B11-0302F0-00102111 Fasten 4PCS hexagonal screws to panel back as illustrated.
Page 41
ITBC0205 v5.0 Model 32L31F\32L41F Document No. Version Mylar Film Sticking Station Name Section/Serial No. Unit Assembly 05 2012-11-1 2012-11-1 Panel K320WD1 series Effective from Date Updated Part Number Amount Descriptions Operations and Requirements Diagram Tool Parameters Tear off the release paper of mylar film, then stick it on panel back as 7912-513190-0750R513 Black power mylar film(L190*W75*T0.5mm) Figure 1/2...
ITBC0206 v5.0 Model 32L31F\32L41F Document No. Version Mainboard Placement Station Name Section/Serial No. Unit Assembly 06 2012-11-1 2012-11-1 Panel K320WD1 series Effective from Date Updated Part Number Amount Descriptions Operations and Requirements Diagram Tool Parameters 32"T9C series 12V MST6M182VG mainboard 9011-11T921-46392251 Put the mainboard on table and check if it looks fine.
Page 43
ITBC0207 v5.0 Model 32L31F\32L41F Document No. Version Mainboard Locking Station Name Section/Serial No. Unit Assembly 07 2012-11-1 2012-11-1 Panel K320WD1 series Effective from Date Updated Part Number Amount Descriptions Operations and Requirements Diagram Tool Parameters Φ3×6mm B-head nickel-plated machine screws 7B11-030696-00101111 Fasten mainboard to panel back with three screws.
Page 44
ITBC0208 v5.0 Model 32L31F\32L41F Document No. Version I/O Baffle Plate Locking Station Name Section/Serial No. Unit Assembly 08 2012-11-1 2012-11-1 Panel K320WD1 series Effective from Date Updated Part Number Amount Descriptions Operations and Requirements Diagram Tool Parameters Φ3×6mm B-head nickel-plated machine screws 7B11-030696-00101111 Take out the LVDS wire from the gap of mainboard.
Page 45
ITBC0209 v5.0 Model 32L31F\32L41F Document No. Version Remote Control Board Locking Station Name Section/Serial No. Unit Assembly 09 2012-11-1 2012-11-1 Panel K320WD1 series Effective from Date Updated Part Number Amount Descriptions Operations and Requirements Diagram Tool Parameters 9015-112L31-61034031 32-42L31 remote control receive board Insert 5pin end of 700|250mm wire to remote control board socket.
ITBC0210 v5.0 Model 32L31F\32L41F Document No. Version Wire Insertion-1 Station Name Section/Serial No. Unit Assembly 10 2012-11-1 2012-11-1 Panel K320WD1 series Effective from Date Updated Part Number Amount Descriptions Operations and Requirements Diagram Tool Parameters 6149-370056-03301211 370mm double-terminal red/black wire Insert 3pin red/black power cord to power socket on mainboard.
Page 47
ITBC0211 v5.0 Model 32L31F\32L41F Document No. Version Wire Insertion-2 Station Name Section/Serial No. Unit Assembly 11 2012-11-1 2012-11-1 Panel K320WD1 series Effective from Date Updated Part Number Amount Descriptions Operations and Requirements Diagram Tool Parameters Insert LVDS wire to LVDS socket on mainboard. Figure 1 Insert backlight end to 10pin socket as illustrated.
Page 48
ITBC0212 v5.0 Model 32L31F\32L41F Document No. Version Wire Insertion-3 Station Name Section/Serial No. Unit Assembly 12 2012-11-1 2012-11-1 Panel K320WD1 series Effective from Date Updated Part Number Amount Descriptions Operations and Requirements Diagram Tool Parameters Insert 200mm 2Pin yellow/black speaker wire to 2pin socket on 6149-200045-02101201 200mm 2Pin yellow/black speaker wire Figure 1...
ITBC0213 v5.0 Model 32L31F\32L41F Document No. Version Wire Arrangement -1 Station Name Section/Serial No. Unit Assembly 13 2012-11-1 2012-11-1 Panel K320WD1 series Effective from Date Updated Part Number Amount Descriptions Operations and Requirements Diagram Tool Parameters 0.13mm×20mm×50m Viscose paper Tear off five pieces of 50mm viscose paper and fix wires in the figure 7912-712500-020R1311 Figure 1 (3M8915)(50mm)
Page 50
ITBC0214 v5.0 Model 32L31F\32L41F Document No. Version Wire Arrangement -2 Station Name Section/Serial No. Unit Assembly 14 2012-11-1 2012-11-1 Panel K320WD1 series Effective from Date Updated Part Number Amount Descriptions Operations and Requirements Diagram Tool Parameters 0.13mm×20mm×50m Viscose paper Tear off two pieces of 50mm viscose paper and fix wires in the figure 7912-712500-020R1311 Figure 1 (3M8915)(50mm)
Page 51
ITBC0215 v5.0 Model 32L31F\32L41F Document No. Version Process Inspection-1 Station Name Section/Serial No. Unit Assembly 15 2012-11-1 2012-11-1 Panel K320WD1 series Effective from Date Updated Part Number Amount Descriptions Operations and Requirements Diagram Tool Parameters Check if all processes for each parts in the machine comply with the requirements of operating instructions.
Page 52
ITBC0216 v5.0 Model 32L31F\32L41F Document No. Version Process Inspection-2 Station Name Section/Serial No. Unit Assembly 16 2012-11-1 2012-11-1 Panel K320WD1 series Effective from Date Updated Part Number Amount Descriptions Operations and Requirements Diagram Tool Parameters Check if all processes for each parts in the machine comply with the requirements of operating instructions.
ITBC0217 v5.0 Model 32L31F\32L41F Document No. Version Back Cover Installation -1 Station Name Section/Serial No. Unit Assembly 17 2012-11-1 2012-11-1 Panel K320WD1 series Effective from Date Updated Part Number Amount Descriptions Operations and Requirements Diagram Tool Parameters Put the processed back cover on assembly board and check if it looks Back cover assembly Figure 1 fine.
Page 54
ITBC0218 v5.0 Model 32L31F\32L41F Document No. Version Back Cover Installation -2 Station Name Section/Serial No. Unit Assembly 18 2012-11-1 2012-11-1 Panel K320WD1 series Effective from Date Updated Part Number Amount Descriptions Operations and Requirements Diagram Tool Parameters Insert red/black and yellow/black speaker wires to left/right speakers Figure 2/3/4 properly.
Page 55
ITBC0219 v5.0 Model 32L31F\32L41F Document No. Version Power Cord Cover Installation Station Name Section/Serial No. Unit Assembly 19 2012-11-1 2012-11-1 Panel K320WD1 series Effective from Date Updated Part Number Amount Descriptions Operations and Requirements Diagram Tool Parameters TV-5 8/128A 250VAG 4pin power switch 6264-250008-13210001 Fit power switch to power cord cover properly.
Page 56
ITBC0220 v5.0 Model 32L31F\32L41F Document No. Version Power Cord Cover Locking Station Name Section/Serial No. Unit Assembly 20 2012-11-1 2012-11-1 Panel K320WD1 series Effective from Date Updated Part Number Amount Descriptions Operations and Requirements Diagram Tool Parameters Ф4×5mm round-head white-zinc-plated machine Fasten ground wire of power to the screw hole of panel back plate with 7B11-0405D6-40102111 Figure 2...
Page 57
ITBC0221 v5.0 Model 32L31F\32L41F Document No. Version Back Cover Locking-1 Station Name Section/Serial No. Unit Assembly 21 2012-11-1 2012-11-1 Panel K320WD1 series Effective from Date Updated Part Number Amount Descriptions Operations and Requirements Diagram Tool Parameters Φ3×13mm flat-head flat-tail black-zinc-plated tapping 7B11-0313A4-00105113 Fasten back cover with four screws.
Page 58
ITBC0222 v5.0 Model 32L31F\32L41F Document No. Version Back Cover Locking-2 Station Name Section/Serial No. Unit Assembly 22 2012-11-1 2012-11-1 Panel K320WD1 series Effective from Date Updated Part Number Amount Descriptions Operations and Requirements Diagram Tool Parameters Φ3×13mm flat-head flat-tail black-zinc-plated tapping 7B11-0313A4-00105113 Fasten back cover with five screws.
Page 59
ITBC0223 v5.0 Model 32L31F\32L41F Document No. Version Back Cover Locking-3 Station Name Section/Serial No. Unit Assembly 23 2012-11-1 2012-11-1 Panel K320WD1 series Effective from Date Updated Part Number Amount Descriptions Operations and Requirements Diagram Tool Parameters Φ3×13mm flat-head flat-tail black-zinc-plated tapping 7B11-0313A4-00105113 Fasten back cover with five screws.
Page 60
ITBC0224 v5.0 Model 32L31F\32L41F Document No. Version Back Cover Locking-4 Station Name Section/Serial No. Unit Assembly 24 2012-11-1 2012-11-1 Panel K320WD1 series Effective from Date Updated Part Number Amount Descriptions Operations and Requirements Diagram Tool Parameters Φ3×6 countersunk-head black-zinc-plated machine Fasten back cover to the panel with two Φ3×6 screws.
Page 61
ITBC0225 v5.0 Model 32L31F\32L41F Document No. Version Back Cover Locking-5 Station Name Section/Serial No. Unit Assembly 25 2012-11-1 2012-11-1 Panel K320WD1 series Effective from Date Updated Part Number Amount Descriptions Operations and Requirements Diagram Tool Parameters Ф4×16mm B-head black-zinc-plated machine screws 7B11-041696-20105111 Fasten back cover to the panel with one screw.
Page 62
ITBC0226 v5.0 Model 32L31F\32L41F Document No. Version Dynamic Inspection Station Name Section/Serial No. Unit Assembly 26 2012-11-1 2012-11-1 Panel K320WD1 series Effective from Date Updated Part Number Amount Descriptions Operations and Requirements Diagram Tool Parameters For specific operations, see figure 1. Remote control When finished, step on the switch with your foot to send the product to Tapping rod...