Page 14
MSD318 Software Upgrades (After Service) 1、 Software upgrade tools and materials u Personal computer (WINDOWS XP system,USB2.0) u AC100~240V power supply and power cord u ISP burning board and connecting line USB flash disk(2.0 version,Capacity not more than 2G) 2、 Preparatory work before the upgrade Recorded all the ADC and the white balance data of all the message source in factory menu before upgrade(FLASH initialization may occur after the upgrade, flush color calibration data, then restore the data you have been recorded): (1)In the condition of YPbPb signal source, press MENU key and pop-up the main menu, then press 8202 number keys...
Page 15
③. When shows "USB Search Success!", move the cursor to "YES" and press OK key, after display "Software Upgrading Please Wait..." the machine will black screen and restart, it means that upgrading complete, turn off the power and pull out U disk. USB Search Failure Press right...
Page 16
4.3. Take out one Φ5×15mm P-head white-zinc-plated tapping screws with flat washers and two Φ4×15mm B-head pointed-tail nickel-plated tapping screws which fastened to the base, move the base assembly from the machine. Φ5×15 screw Φ4×15screw Φ4×15screw 4.4. Take down Φ3×14 sink-head pointed-tail black-zinc-plated tapping screws(1-2# screws) 、Φ3×10 sink-head pointed-tail black-zinc-plated tapping screws(1# screw) and Φ3×10 sink-head machine screws (4,5,6# screws)which fastened to the back cover.
Page 17
4.6. Open the back cover carefully. ③ Notice: a). Need special tools to open. Do not force pull the back cover from surface frame, to avoid break out the button of surface frame, causing the ② ④ back cover and the surface frame with big crevice.。...
Page 18
到 PC 端 到主板 ISP 4pin 插座 To mainboard (2) Insert the Mstar USB tool into the USB port of your PC. The PC can recognize the new device. You can choose to install it in the list, or choose to install at a specified directory and specify the path to the drive file. See the figure below:...
Page 19
(3) When the PC finds the drive file, it will give the prompts as in the figure below during the installation process. Please click “Continue" to go ahead. The system will go through three drive installation processes, including Mstar USB Debug Tool A, Mstar USB Debug Tool B, and Mstar USB SerialPort.
Page 20
To mainboard ISP 4pin socket Insert power cord Power switch is on (2). In the config menu bar to select Use USB and Auto release USB, Communication Setting items corresponding to the Port Type menu select USB。Set the burning speed of 48 in I2C Speed Setting item, ISP Slave Address item menu select OX92,Serial Debug Slave Address menu select 0XB2。...
Page 21
Normal connection will display: Device Type is EN25B64; Abnormal connection display: Can’t Entry ISP Mode! (4). Press Load button in the main menu,in the popping menu click button to load TV mainboard program. bin file. Load button The loading path (5).
Page 22
Read bottom The loading path (6).Other function setting and loading item as following figure, Please click Run to burn the software: In blank space (prompt area for burning) you will see a lot of information related to burning. About six minutes later, the word “Pass"...
Page 23
completed, change the TV and click Run key to burn next machine. 5、When upgrade complete, install the machine back cover, then must be adjusted before leave the factory: (1). Power to the machine, press MENU key to popping the main menu, press 8202 number keys and then will popping the factory menu automatically, move the cursor to the "Reset"...
Need help?
Do you have a question about the LE32W164 and is the answer not in the manual?
Questions and answers