Marantz WB6001T User Manual
  1. Manuals
  2. Brands
  3. Marantz Manuals
  4. Racks & Stands
  5. WB6001T
  6. User manual
Marantz WB6001T User Manual

Marantz WB6001T User Manual

Tilt flat wall mount for 61” plasma
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Model WB6001T User Guide
Tilt Flat Wall Mount for 61" Plasma

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WB6001T and is the answer not in the manual?

Questions and answers

Related Manuals for Marantz WB6001T

Summary of Contents for Marantz WB6001T

  • Page 1 Model WB6001T User Guide Tilt Flat Wall Mount for 61” Plasma...

  • Page 2: Warning Statements

    Failure to do so may result in damage to the flat panel display and could increase the risk of fire. At least two qualified people should perform the installation procedure. Injury and/or damage can result from dropping or mishandling the flat panel display. Warning Statements Contact Marantz with any questions - (630)-741-0300.

  • Page 3: Table Of Contents

    Warning Statements ...- 2 - PARTS LIST ...- 4 - Installation Tools ...- 4 - FINDING THE CENTER OF THE DISPLAY ...- 5 - POSITIONING THE MOUNTING BRACKETS ...- 6 - SECURING THE MOUNTING BRACKETS ...- 7 - WOODEN STUD LOCATION ...- 8 - FLAT PANEL INSTALLATION ...- 12 - LATERAL SHIFT ADJUSTMENT ...- 12 - TECHNICAL SPECIFICATIONS ...- 13 -...

  • Page 4: Parts List

    NOTE: This wall mount is shipped with all proper installation hardware and components. Make sure that none of these parts are missing before beginning installation. If there are parts missing stop the installation and contact Marantz. Wall plate (Qty 2)

  • Page 5: Finding The Center Of The Display

    FINDING THE CENTER OF THE DISPLAY WARNING: Proper installation procedure by qualified personnel as outlined in the installation instructions must be adhered to. Failure to do so could result in serious personal injury and possible damage to the flat panel. WARNING: DO NOT LAY THE FLAT PANEL ON THE FLOOR DURING ANY STEP OF THE INSTALLATION PROCESS..

  • Page 6: Positioning The Mounting Brackets

    POSITIONING THE MOUNTING BRACKETS Step 3 Lay the mounting brackets (stamped arrows facing out) - (Figure 3). Arrows Facing Out Figure 3 Step 5 The mounting brackets are designed with a center viewing guide on the side of them (Figure 5). Figure 5 - 6 - Step 4...

  • Page 7: Securing The Mounting Brackets

    SECURING THE MOUNTING BRACKETS Step 6 The Griplates™ have M4, M5, M6 and M8 hole patterns to fit the hardware that your flat panel requires. EXAMPLE: If your plasma uses M8 x 20 Phillip screws. Use the M8 mounting points (Figure 6). DIMPLES Figure 6 Step 7...

  • Page 8: Wooden Stud Location

    WOODEN STUD LOCATION Step 8 Using a (commercially available) wood stud finder, locate the 16" or 24" stud centers behind the wall. Once found, make a pencil marking on the center of the wood studs (Figure 8). NOTE: The wall plates have (3) 16" and (1) 24"...
  • Page 9 Step 10 Place the bottom portion of the wall plate to the reference line and mark the four (4) lag bolt mounting points through the wall plate slots on the wall (Figure 10). 16" Figure 10 Step 11 Level the wall plate with the reference arrow pointing up to the ceiling (Figure 11).
  • Page 10 Step 12 – Wooden Stud Installation Level and secure the lower plate to the wall with the reference arrow facing up to the ceiling. Secure the plate using the four (4) 5/16" lag bolts and flat washers (supplied) – (Figure 12). Repeat Step 5 to secure the upper wall plate to the wall (Figure 12).

  • Page 11: Step 13 - Concrete Installation

    Step 13 – Concrete Installation Level and secure the lower plate to the wall with the reference arrow facing up to the ceiling. NOTE: Each hole must be drilled using a 7/16” drill bit. Use a diameter of 3/8” x 2 ¼” large concrete wedge anchors (commercially available) – (Figure 14). Gently tap the wedge anchor into the hole.

  • Page 12: Flat Panel Installation

    FLAT PANEL INSTALLATION Step 14 WARNING: AT LEAST (2) QUALIFIED PERSONNEL ARE STRONGLY RECOMMENDED FOR INSTALLATION OF THIS PRODUCT. FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY AND POSSIBLE DAMAGE TO THE FLAT PANEL. Raise the flat panel with the mounting brackets secured to the flat panel and insert the top hooks from each bracket to the rod from the wall plates (Figure 15).

  • Page 13: Technical Specifications

    TECHNICAL SPECIFICATIONS Dimensions are in Inches and ( 19.000 12.000 (482.6) (304.8) A. Wall plate B. Mounting brackets C. Griplate™ D. Mounting hardware E. M6 x 30 (mm) Phillip screws F. Wood stud G. 5/16” x 3” Lag screws and flat washers H.
  • Page 14 You can find your nearest authorized distributor or dealer on our website. Marantz America, Inc. 1100 Maplewood Drive, Itasca, IL 60143, U.S.A. U.S.A. is a registered trademark. - 14 -...

Table of Contents