Programming; Remarks About Programming - Marantz DR4050 User Manual

PROGRAMMING

Remarks about programming

• You can program up to 99 tracks to play in any desired
sequence.
• Tracks can be programmed more than once, but each time
counts as a track. ( )
S S T T E E P P
• A program for playback can be made from both the disc in
the recorder deck and the disc in the player deck. A program
for recording can only be made from the disc in the player
deck.
Programming for playback
1 1 Select Changer mode or DJ mode using the DJ MODE key.
CHANGER or DJ MODE appears on the display.
2 2 Press CDR or CD to select the required deck.
Selected key lights up.
3 3 Press PROG(ram) to enter Program mode.
flashes and PROGRAM followed by track
P P R R O O G G
information appears on the display.
REM REC TIME TRACK TOTAL REM
1 2 3 4 5 6 7 8 9 10 11
SYNC MANUAL
RECORD
CHANGER
DIGITAL I CD
OPTICAL I
RW
ANALOG
REM REC TIME TRACK TOTAL REM
1
SYNC MANUAL
RECORD
DIGITAL I CHANGER
CD
OPTICAL I
RW
ANALOG
4 4 Select the required track numbers by turning the EASY
JOG/ENTER key left or right and store by pressing ENTER.
REM REC TIME TRACK TOTAL REM
2 7 8 11
SYNC MANUAL
RECORD
DIGITAL I CD CHANGER
OPTICAL I
RW
ANALOG
or:
Key in a track number with the number keys on the remote
control and press ENTER to confirm. For 2-digit numbers,
press the keys in rapid succession.
The track will be stored in the program.
The track number, total program time and the number of
programmed tracks ( ) are displayed.
S S T T E E P P
5 5 Repeat step 4 4 for all tracks to be programmed.
6 6 Press STOP or PROG(ram) to end programming.
lights continuously.
P P R R O O G G
7 7 Press PLAY/PAUSE 2 ; to start programmed play.
26
Programming for recording
1 1 Press REC TYPE to select the required recording mode (see
'Recording').
2 2 Compile your programme as described in "programming for
playback". (steps 3 to 5)
• Only tracks from the disc in the CD player can be stored.
3 3 Press REC(ord). to start recording.
Note:
- To review the program, press PROG(ram), followed by 5 or
6 with the CD player or CD recorder in stop mode.
- To add more tracks to the program, repeat steps 1 1 to 7 7 .
- If you try to store more than 99 tracks, PROG FULL
appears on the display.
Clearing a program
1 1 Press STOP 9 if necessary to stop programmed play.
2 2 Press STOP 9 again to clear the program.
TRACK TIME STEP
• The program is also cleared if you open the disc tray.
PROG
Erasing a track from a program
SHUFFLE ALL
CD
REPEAT
RW
SCAN TRACK
1 1 In Stop mode press PROG(ram) to enter Program mode.
TRACK TIME STEP
2 2 Use 5 or 6 to select the track that has to be deleted.
PROG
SHUFFLE ALL
CD
REPEAT
RW
SCAN TRACK
3 3 Press CANCEL/DELETE to erase the track from the program.
TRACK TIME STEP
4 Repeat step 2 and 3 for all tracks to be erased.
PROG
5 Press STOP 9 or PROG(ram) to end erasing.
SHUFFLE ALL
CD
REPEAT
RW
SCAN TRACK
disappears from the display.
P P R R O O G G
The track number and program step will be shown on
the display.
The remaining program steps and the remaining playing
time of the program will be displayed.
lights continuosly.
P P R R O O G G