EWM T5.00 Operating Instructions Manual page 4

Contents
Notes on using these operating instructions
5.2.6
5.2.7
5.2.8
5.2.9
5.2.10
5.2.11
5.2.12
5.2.13
5.3 MMA welding........................................................................................................54
5.3.1
5.3.2
5.3.3
5.3.4
5.3.5
5.3.6
5.3.7
5.4 Arc length restriction (USP).....................................................................................57
5.5 JOB favourites ......................................................................................................58
5.5.1
5.5.2
5.5.3
5.6 Managing welding tasks (JOB manager) ...................................................................59
5.6.1
5.6.2
5.7 Power-saving mode (Standby) ................................................................................60
5.8 Access control ......................................................................................................60
5.9 Voltage reducing device .........................................................................................61
5.10 Dynamic power adjustment.....................................................................................61
5.11 Machine configuration menu ...................................................................................61
5.11.1
6 Maintenance, care and disposal ....................................................................................67
6.1 General ...............................................................................................................67
6.2 Disposing of equipment..........................................................................................68
7 Rectifying faults ...........................................................................................................69
7.1 Warnings .............................................................................................................69
7.2 Error messages (power source)...............................................................................71
7.3 Resetting welding parameters to the factory settings ..................................................77
7.4 Software version of the machine control ...................................................................77
8 Appendix .....................................................................................................................78
8.1 Parameter overview - setting ranges .......................................................................78
8.1.1
8.1.2
8.1.3
4
TIG activArc welding ................................................................................41
TIG antistick............................................................................................41
Pulse welding..........................................................................................42
Average value pulse welding .....................................................................42
5.2.9.1 Thermal pulsing .........................................................................43
5.2.9.2 Automated pulses.......................................................................43
5.2.9.3 AC special.................................................................................44
5.2.9.4 Pulsing in an upslope/downslope ..................................................44
Welding torch (operating variants) ..............................................................45
5.2.10.1 Welding torch mode ....................................................................45
5.2.10.2 Tapping function (tap torch trigger)................................................48
5.2.10.3 Up/down speed ..........................................................................48
5.2.10.4 Current jump..............................................................................48
RTF 1 foot-operated remote control ............................................................49
5.2.11.1 Start ramp .................................................................................49
5.2.11.2 Responsiveness.........................................................................50
Expert menu (TIG) ...................................................................................51
Aligning the cable resistance .....................................................................52
Welding task selection ..............................................................................54
Hotstart ..................................................................................................54
5.3.2.1 Selection and adjustment.............................................................54
Arcforce .................................................................................................55
Antistick .................................................................................................55
Welding current polarity reversal (polarity reversal) .......................................56
AC welding .............................................................................................56
5.3.6.1 Automatic AC f requency ..............................................................56
Pulse welding..........................................................................................57
5.3.7.1 Average value pulse welding ........................................................57
Saving current settings to Favourites ..........................................................58
Loading saved Favourites .........................................................................58
Deleting saved Favourites.........................................................................59
Copying welding tasks (JOB) .....................................................................59
Reset welding task (JOB) to the f actory setting.............................................60
Selecting, changing and saving parameters .................................................61
TIG welding ............................................................................................78
8.1.1.1 Pulse parameters .......................................................................79
8.1.1.2 AC parameters...........................................................................79
MMA welding ..........................................................................................79
8.1.2.1 Pulse parameters .......................................................................80
8.1.2.2 AC parameters...........................................................................80
Global parameters ...................................................................................80
099-00T500-EW501
2.9.2022