Front Runner SLIMLINE II KRFE009T Read Me First

Front Runner SLIMLINE II KRFE009T Read Me First

Ford expedition/lincoln navigator (2018-current) roof rail rack kit

Advertisement

front runner
START HERE!
Don't be a hero and muscle through this installation without reading these fitting instructions first! Improper installation of this gear may void certain
aspects of your warranty.
Before you begin, take a moment and open all your Front Runner rack kit boxes and gather the assembly instructions for the various components.
A complete kit will contain:
1. A Front Runner Mounting System specific to your vehicle
2. A Front Runner Rack Tray or Load Bar Slats
This document will guide you through the assembly of the mounting system and assist you in fitting the roof rack tray or load bars to your specific
vehicle.
Please refer to the next page for a list of all the components, quantities and tools required.
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
KRFE009T_REV_A00
FORD EXPEDITION/LINCOLN NAVIGATOR
(2018-CURRENT) SLIMLINE II ROOF RAIL RACK KIT
READ ME FIRST
IMPORTANT WARNING!
Please call us if you have any questions about the installation of this product.
1
KRFE009T
© 2022 FRONT RUNNER VEHICLE OUTFITTERS
ENG

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SLIMLINE II KRFE009T and is the answer not in the manual?

Questions and answers

Summary of Contents for Front Runner SLIMLINE II KRFE009T

  • Page 1 Don’t be a hero and muscle through this installation without reading these fitting instructions first! Improper installation of this gear may void certain aspects of your warranty. Before you begin, take a moment and open all your Front Runner rack kit boxes and gather the assembly instructions for the various components. A complete kit will contain: 1.
  • Page 2 IN THE BOX TOOLS NEEDED Slimline II Tray - 1425mm(W) X 1762mm(L) Spacer Grab On Foot 13mm Outer Grip (5) Inner Grip (A) Wind Deflector 20mm Lip Wide Pair / 1345mm FIGURE 1.1 KRFE009T_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS...
  • Page 3 Refer to GOFR001 fitment guide. Remove the Front Covers from all the Base Feet by loosening the two M5x10 Button Head Screws. Loosen and remove the M5x60 Cap Screw, M5 Spring Washer and Cap Screw Washer. KRFE009T_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS...
  • Page 4 Make sure there is no movement on the rack after fully tightening all the fasteners. Refit the Front Cover Plates. Center the rack and tighten fully. Finish off by placing M8 Nut Caps over the M8 Nyloc Nuts. KRFE009T_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS...
  • Page 5 IMPORTANT! FRONT RUNNER RACK KITS OFTEN HAVE A HIGHER LOAD RATING THAN THE VEHICLES THEY ARE MOUNTED TO. PLEASE REFER TO YOUR SPECIFIC VEHICLE MANUFACTURER FOR A RECOMMENDED ROOF RATING. FRONT RUNNER CANNOT BE RESPONSIBLE FOR IMPROPER LOADING BEYOND THE VEHICLE MANUFACTURER'S STATED LOAD CAPACITY.

Table of Contents