Advertisement
aSSembLy inSTruCTionS
STep 1
Lay out all the included components and hardware
to ensure you have everything listed on the parts page.
Take four of the self-adhesive Noise Attenuation Pads (P5)
and place them on the VT Brackets (P4) as shown.
STep 2
Place the VT Brackets (P4) on the underside of the
surface you will be lifting. Use the included 24 Wood Screws (P13)
to attach the Brackets in place, using six screws per bracket.
Caution: Double-check that the wood screws
(P13) are short enough that they won't puncture a
hole in your surface when screwed in completely
If your surface is not pre-drilled we recommend
you pre-drill any holes needed for the VT Brackets
(P4). Never use countersunk screws
STep 3
Place the 4 Legs (P1) into the 4 VT Brackets (P4) as shown.
Using the supplied Allen Wrench, loosely thread the M6X14
Machine Screws (P12) into the remaining holes on each of the
VT Brackets (P4) to secure the 4 legs (P1). Once all screws are
in place, fully tighten all four screws.
STep 4
Now that the Legs (P1) are secure you can attach the 4
Stand-Offs (P2) and 4 Glides (P3) to the bottom of each leg
as shown. Secure the Stand-Offs (P2) and Glides (P3) with the
remaining M6X14 Machine Screws (P12), 4 per leg.
STep 5
Attach the Control Box (P6) to the underside of your surface
using two of the M5X16 Screws (P14) per box. Make sure you
leave enough room for cable connections into the wire ports
on each box. Next find a suitable area to place your Remote
(P8), we recommend somewhere on the end of your surface
along the front edge. Once you're happy with its position
you can attach it using 2 x M5X16 Screws.
As stated earlier make sure the screws are short
enough that they don't puncture a hole in your
surface when screwed in completely. Do not
overtighten the screws here, overtightening may
cause damage to the components.
how To order
1.800.676.6123
STep 6
Now that everything's in place we can start connecting it all
together. Take the CB Cable (P10) and connect the control
boxes together via the small ports located on the side of the
boxes. Connect the remote (P8) to the Control Box (P6).
Use the 4 LC Cables (P9) to connect each Leg (P1) to the
Control Box (P6). Finally take the 2 Power Cables (P11) and
connect each one to the control box. Use the included
adhesive-backed Cable Clips (P15) to secure all the wires so
they don't get tangled.
STep 7
Once you have everything connected and secure, carefully turn
your surface right-side-up. We recommend using at least 2
people to do this. Adjust the pre-installed Glides (P3) as needed.
STep 8
Plug the Power Cables (P11) from the
Control Box (P6, P7) into an outlet.
imporTanT
You MUST reset the table lift prior to use.
reSeT proCedure
If you've raised the table lift at all then press and hold the
down button on the Remote (P8) until the lift is at its lowest,
then release the button. Then press and hold the down
button for 10 seconds until the LED display reads "ASr". If
you are using a spare remote without LED then hold onto the
down button for about 10 seconds then release.
Press and hold the down button one more time until the desk
lowers a bit more, slightly rises and then stops. Release the
button and your table lift is now ready for action.
You can preset up to 4 positions by following this simple
procedure. Use the up/down buttons on the remote to find
your desired height(s), then press "M" followed by a number
1-4., then wait a few seconds until the height is displayed
again. To move to the set position, hold the number button.
|
sales@progressiveautomations.com
Ensure the boxes and remote are placed so the
wires can reach between everything
|
www.progressiveautomations.com
Page 4 of 5
Advertisement
