Kohler STERLING SP5400 Series Installation And Care Instructions

Sliding Shower Doors
USA/Canada: 1-800-STERLING (1-800-783-7546)
México: 001-877-680-1310 SterlingPlumbing.com
Critical Information!
Read Before Installation!
WARNING: Risk of serious injury. Damage prior to installation can
result in glass shattering. Inspect the glass and all parts for damage
before installation.
WARNING: Risk of serious injury. Improper installation can result
in glass shattering. Follow all installation instructions.
WARNING: Risk of serious injury. Do not cut tempered glass.
Tempered glass will shatter if cut.
WARNING: Risk of serious injury. Shower door and side panels
can shatter. Regularly inspect the glass and all parts for damage,
missing, or loose parts.
WARNING: Risk of serious injury. Always wear safety glasses
while cutting and drilling.
IMPORTANT! Do not touch the edges of the tempered glass with tools or
any other hard objects. Do not set the unframed tempered glass directly on
the floor or any hard surface.
IMPORTANT! Leave this manual for the end user.
Read these instructions before installing or using this product.
IMPORTANT! Do not cut the top track the same length as the bottom track.
NOTICE: The warranty does not apply to a product that has been modified
or altered in a manner other than as expressly permitted in the Installation
and Care Guide.
Walls must be within 3/8" (10 mm) of plumb.
Cover the drain with tape to avoid loss of small parts.
Follow the silicone sealant manufacturer's instructions for application and
curing time.
To watch this installation video online, visit www.sterlingplumbing.com.
For care and cleaning and other information; visit
www.sterlingplumbing.com/care-and-cleaning.
Read and follow all instructions.
Slide the notched end of the insert into the
1
groove and pull the notch to the end of the
bottom track. Trim the insert to be flush with the
bottom track.
Insert
Bottom Track
Apply silicone sealant in the groove on the
6
underside of the bottom track. Secure the bottom
track to the ledge along the marked location.
Groove
1204890-2-D
Required Tools
1/16"
Tin Snips
100% Silicone Sealant
Masking Tape
32 Teeth Per Inch Blade
Miter Box
Center the bottom track on the ledge with the leg
2
to the outside. Tape the bottom track in place and
mark the position.
Leg
Reposition both wall jambs. Secure the wall
7
jambs with screws. Attach a bumper at the top
and bottom locations.
Screw Cover
x2
Screw
Cover
#8-18 x 2"
Parts Identifi cation
1205305**
Hanger Bracket Kit
1203634
Hardware Skin Pack
Series Number
Label
1058827-02**
Top Track
1199426-01** 1051142-A
Hanger Bracket Screw
#8-32 x 3/8"
1199110
Gasket
1050048-B
Barrel Nut
1077763-A
Bolt
#8-32 x 1/4"
1093027
Spacer (8 ea.)
Door Panel*
1048208-N
Screw
#8-18 x 2"
Position the wall jambs over the bottom track.
3
Plumb both wall jambs. Mark the screw holes.
x2
Check the bumpers for the correct horizontal
8
alignment with the wall jambs.
Correct Incorrect
1
Installation and Care Instructions
SP5400 Series Sliding Shower and Bath Doors
*Need help? Contact the STERLING Customer Care Center at 1-800-STERLING
For service parts information, care and cleaning, and other information, visit
1044585
Roller
1057704-02** [20" (508 mm)]
1057704-01** [24" (610 mm)]
Towel Bar
1056868-A
1053530
Screw
Insert
1058294**
Center Guide
1058626-11** (SP5475-57)
1058626-12** (SP5465-45)
Bottom Track
Tile Installations Only
4
Nick the tile at the mark for the hole before
drilling with a center punch. This keeps the drill
bit from moving as the hole is started.
When installing to a tile wall, first drill a small
diameter hole, then a larger hole.
Install anchors. Do not install the screws directly
into the tile, as this may crack the tile.
When drilling, use a masonry bit.
Mark
Center
Punch
Measure distance "B" above the wall jambs.
9
Subtract 1/32" (1 mm) or the width of a saw
blade from "B." Mark and cut the top track.
Top Track
B
1/32"
(1 mm)
Cut Line
"B" Mark
B
(1-800-783-7546).
www.sterlingplumbing.com
**Finish/color code must be specifi ed when ordering.
Retain this document for future servicing.
Record model number from box for reference.
Model Number:______________
Wall Jamb*
1081001
Bumper
1031943**
1077762
Screw Cover
Anchor
Remove the wall jambs. Drill 5/16" holes into the
5
walls and insert the anchors.
x2
3
2
1
Position the top track over the wall jambs. Either
10
side of the top track may face out.
Reversible