Advertisement

Quick Links

The information in this User's Manual has been carefully reviewed and is believed to be accurate. The vendor assumes
no responsibility for any inaccuracies that may be contained in this document, and makes no commitment to update
or to keep current the information in this manual, or to notify any person or organization of the updates. Please Note:
For the most up-to-date version of this manual, please see our website at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product described in this manual
at any time and without notice. This product, including software and documentation, is the property of Supermicro and/
or its licensors, and is supplied only under a license. Any use or reproduction of this product is not allowed, except
as expressly permitted by the terms of said license.
IN NO EVENT WILL Super Micro Computer, Inc. BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT
OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPER
MICRO COMPUTER, INC. SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED
OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING,
INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.
SuperServer
®
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara County in the
State of California, USA. The State of California, County of Santa Clara shall be the exclusive venue for the resolution
5019S-L
of any such disputes. Supermicro's total liability for all claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class A digital device
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the manufacturer's instruction manual,
may cause harmful interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning applies only
to products containing CR (Manganese Dioxide) Lithium coin cells. "Perchlorate Material-special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate".
WARNING: Handling of lead solder materials used in this product may expose you to lead, a
chemical known to the State of California to cause birth defects and other reproductive harm.
The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment,
nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency communication devices or other critical
systems whose failure to perform be reasonably expected to result in significant injury or loss of life or catastrophic
property damage. Accordingly, Supermicro disclaims any and all liability, and should buyer use or sell such products
for use in such ultra-hazardous applications, it does so entirely at its own risk. Furthermore, buyer agrees to fully
indemnify, defend and hold Supermicro harmless for and against any and all claims, demands, actions, litigation, and
proceedings of any kind arising out of or related to such ultra-hazardous use or sale.
Manual Revision 1.0
Release Date: November 25, 2015
Unless you request and receive written permission from Super Micro Computer, Inc., you may not copy any part of this
document. Information in this document is subject to change without notice. Other products and companies referred
to herein are trademarks or registered trademarks of their respective companies or mark holders.
USER'S MANUAL
Copyright © 2015 by Super Micro Computer, Inc.
All rights reserved.
Revision 1.0
Printed in the United States of America
2

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SuperServer 5019S-L and is the answer not in the manual?

Questions and answers

Summary of Contents for Supermicro SuperServer 5019S-L

  • Page 1 5019S-L of any such disputes. Supermicro's total liability for all claims will not exceed the price paid for the hardware product. FCC Statement: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules.
  • Page 2: Table Of Contents

    This manual is written for professional system integrators and PC technicians. It provides 1.3 System Specifications ......................9 information for the installation and use of the SuperServer 5019S-L. Installation and maintainance should be performed by experienced technicians only. 1.4 Server Chassis Features ....................10 Please refer to the 5019S-L server specifications page on our website for updates on Control Panel ........................10...
  • Page 3 SuperServer 5019S-L User's Manual Preface PCI Expansion Card Installation ..................29 6.6 Security ..........................90 Motherboard Battery ......................29 6.7 Boot ............................93 3.4 Chassis Components ......................30 6.8 Save & Exit .........................95 Appendix A BIOS Error Codes Hard Drives ........................30 Appendix B Standardized Warning Statements for AC Systems System Cooling .........................31...
  • Page 4 Super Micro Computer, Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. Tel: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.com (Technical Support) Website: www.supermicro.com Europe Address: Super Micro Computer B.V. Het Sterrenbeeld 28, 5215 ML...
  • Page 5: Chapter 1 Introduction

    One PCI Express 3.0 x8 in x16 slot (CPU slot 6) One PCI Express 3.0 x8 slot (CPU slot 7) Inspect the box the SuperServer 5019S-L was shipped in and note if it was damaged in any Hard Drives way. If any equipment appears damaged, please file a damage claim with the carrier who One 3.5"...
  • Page 6: Server Chassis Features

    SuperServer 5019S-L User's Manual Chapter 1: Introduction 1.4 Server Chassis Features Front Features The SC510-203B is a 11.3"-depth mini 1U chassis. See the illustration below for the features included on the front of the chassis. Control Panel The switches and LEDs located on the control panel are described below. See Chapter 4 for more details on the control panel.
  • Page 7: Rear Features

    SuperServer 5019S-L User's Manual Chapter 1: Introduction Rear Features 1.5 Motherboard Layout The illustration below shows the features included on the rear of the chassis. Below is a layout of the X11SSL-F with jumper, connector and LED locations shown. See the table on the following page for descriptions.
  • Page 8: Quick Reference Table

    SuperServer 5019S-L User's Manual Chapter 1: Introduction Connector Description Quick Reference Table PCI-E (PCH) Slot 5 PCI-Express 3.0 x4in x8 Slot Jumper Description Default Setting Internal Speaker/Buzzer C1/JI SMB to PCI Slots Enable/Disable Pins 1-2 (Enabled) USB 0/1 Back Panel USB 2.0 Ports...
  • Page 9 SuperServer 5019S-L User's Manual #A-2 #A-1 IMVP 8 3 PHASE for Vcore #B-2 #B-1 PCI-E X8 Gen3 PCIe3.0 x8 (in x8) #8-15 Skt-H4 PCI-E X8 Gen3 LGA1151 #0-7 PCIe3.0 x8 (in x16) DMI3 DMI3 x4 PCI-E x4 Gen3 PCI-E X1 Gen3...
  • Page 10: Chapter 2 Server Installation

    SuperServer 5019S-L User's Manual Chapter 2: Server Installation Chapter 2 • In single rack installations, stabilizers should be attached to the rack. In multiple rack in- stallations, the racks should be coupled together. • Always make sure the rack is stable before extending a server or other component from Server Installation the rack.
  • Page 11: Circuit Overloading

    SuperServer 5019S-L User's Manual Chapter 2: Server Installation 2.3 Installing the System into a Rack Circuit Overloading Consideration should be given to the connection of the equipment to the power supply circuitry The following is a basic guideline for installing the system into a rack with the rack mounting and the effect that any possible overloading of circuits might have on overcurrent protection hardware provided.
  • Page 12: Chapter 3 Maintenance And Component Installation

    3. Lift the cover upward to remove it from the chassis. See Figure 3-1. • Refer to the Supermicro website for updates on CPU support. Warning: Except for short periods of time, do not operate the server without the cover in place.
  • Page 13 SuperServer 5019S-L User's Manual Chapter 3: Maintenance and Component Installation Load Plate Load Lever Figure 3-4. Inspecting the Processor Installation Figure 3-2. Removing the Processor Cover Plate 5. With the processor inserted into the socket, inspect the four corners of the CPU to make sure that it is properly installed and flush with the socket.
  • Page 14 SuperServer 5019S-L User's Manual Chapter 3: Maintenance and Component Installation Loosen screws in sequence as shown. Screw#2 Screw#1 Screw#4 Screw#1 Screw#2 Motherboard Motherboard Mounting Holes Screw#3 Heatsink Bracket Heatsink Bracket Figure 3-7. Removing the Heatsink Figure 3-6. Installing the Heatsink 4.
  • Page 15: Memory Installation

    16GB 32GB UDIMM (4x 4GB DIMMs) (4x 8GB DIMMs) Dual Rank 32GB 64GB Figure 3-8. Installing DIMMs UDIMMs (4x 8GB DIMMs) (4x 16GB DIMMs) Note: Visit the product page on the Supermicro website for possible updates to memory support (www.supermicro.com).
  • Page 16: Pci Expansion Card Installation

    Figure 3-11. Installing a 3.5" Drive in the Chassis Note: Enterprise level hard disk drives are recommended for use in Supermicro chassis and servers. For information on recommended HDDs, visit the Supermicro website at http://www.
  • Page 17: System Cooling

    SuperServer 5019S-L User's Manual Chapter 3: Maintenance and Component Installation Brackets Fan housing mounting screw Figure 3-13. System Fans Note: Figure is for illustrative purposes only. The fan positions may be different in your system. Figure 3-12. Installing 2.5" Drives in the Chassis Note: Figure is for illustrative purposes only.
  • Page 18: Power Supply

    If the power supply unit fails, the system will shut down and you will need to replace the unit. Replacement units can be ordered directly from Supermicro. 2. Align the mounting thru holes on the power supply with the mounting holes in the...
  • Page 19: Chapter 4 Motherboard Connections

    SuperServer 5019S-L User's Manual Chapter 4: Motherboard Connections Chapter 4 Processor Power Connector JPWR2 must also be connected to the power supply. This connector is used to power the processor(s). Motherboard Connections +12V 8-pin Power Pin Definitions This section describes the connections on the motherboard and provides pinout definitions.
  • Page 20 SuperServer 5019S-L User's Manual Chapter 4: Motherboard Connections TPM/Port 80 Header Power LED/Speaker A Trusted Platform Module (TPM)/Port 80 header is located at JTPM1 to provide TPM support Pins 1-3 of JD1 are used for power LED indication and pins 4-7 are for the speaker. Please note that the speaker connector pins (4-7) are used with an external speaker.
  • Page 21 Pin# Definition Data Note: UID can also be triggered via IPMI on the motherboard. For more information on IPMI, please refer to the IPMI User's Guide posted on our website at http://www.supermicro.com. Clock UID Switch UID LED Pin Definitions...
  • Page 22: Control Panel

    SuperServer 5019S-L User's Manual Chapter 4: Motherboard Connections Control Panel Reset Button The Reset Button connection is located on pins 3 and 4 of JF1. Attach it to a hardware reset JF1 contains header pins for various control panel connections. See the figure below for the switch on the computer case.
  • Page 23: Data Cables

    SuperServer 5019S-L User's Manual Chapter 4: Motherboard Connections NIC1/NIC2 (LAN1/LAN2) NMI Button The NIC (Network Interface Controller) LED connection for LAN port 1 is located on pins 11 The non-maskable interrupt button header is located on pins 19 and 20 of JF1.
  • Page 24: Ports

    The X11SSL-F includes a total of six SATA ports, supported by the Intel C232 PCH chip. These SATA ports support RAID 0, 1, 5, and 10. Back Panel USB 0/1 (USB 2.0) Front Panel USB 2/3, 4/5 (USB 2.0) Notes: I-SATA0 and I-SATA1 are Supermicro SuperDOMs. These are yellow SATADOM ports Pin Definitions Pin Definitions Pin#...
  • Page 25: Jumpers

    SuperServer 5019S-L User's Manual Chapter 4: Motherboard Connections VGA Port CMOS Clear A video (VGA) port is located next to LAN2 on the I/O back panel. JBT1 is used to clear CMOS, which will also clear any passwords. Instead of pins, this jumper consists of contact pads to prevent accidentally clearing the contents of CMOS.
  • Page 26 SuperServer 5019S-L User's Manual Chapter 4: Motherboard Connections LAN1/2 Enable/Disable BIOS Recovery Change the setting of jumper JPL1 and JPL2 to enable or disable the LAN1 and LAN2 Use jumper JBR1 to recover the BIOS settings on the motherboard. The default setting is Ethernets ports, respectively.
  • Page 27: Led Indicators

    SuperServer 5019S-L User's Manual Chapter 4: Motherboard Connections 4.5 LED Indicators BMC Heartbeat LED A BMC Heartbeat LED is located at LEDBMC on the motherboard. When LEDBMC is blinking, the BMC is functioning normally. LAN LEDs Two LAN ports are located on the rear I/O panel of the motherboard. Each Ethernet LAN Onboard Power LED Indicator port has two LEDs.
  • Page 28: Chapter 5 Software

    SuperServer 5019S-L User's Manual Chapter 5: Software Chapter 5 5.2 Driver Installation The Supermicro FTP site contains drivers and utilities for your system at ftp://ftp.supermicro. com. Some of these must be installed, such as the chipset driver. Software After accessing the FTP site, go into the CDR_Images directory and locate the ISO file for your motherboard.
  • Page 29: Superdoctor ® 5

    5.4 IPMI ® The Supermicro SuperDoctor 5 is a program that functions in a command-line or web-based The X11SSL-F support the Inteliigent Platform Management Interface (IPMI). IPMI is used to interface for Windows and Linux operating systems. The program monitors such system health provide remote access, monitoring and management.
  • Page 30: Chapter 6 Bios

    The date's default value is 01/01/2014 after RTC reset. hot keys (<F1>, <F2>, <F3>, <Enter>, <ESC>, <Arrow> keys, etc.) can be used at any time during the setup navigation process. Supermicro X11SSM-F BIOS Version This item displays the version of the BIOS ROM used in the system.
  • Page 31: Advanced Setup Configurations

    5019S-L User's Manual Chapter 6: BIOS 6.3 A dvanced Setup Configurations Memory Information Total Memory Use the arrow keys to select Boot Setup and press <Enter> to access the submenu items. This item displays the total size of memory available in the system. Memory Speed This item displays the memory speed.
  • Page 32 5019S-L User's Manual Chapter 6: BIOS Wait For 'F1' If Error CPU Configuration Use this feature to force the system to wait until the 'F1' key is pressed if an error occurs. The following CPU information will display: The options are Disabled and Enabled. •...
  • Page 33 5019S-L User's Manual Chapter 6: BIOS Active Processor Cores Package Power Limit MSR Lock This feature determines how many CPU cores will be activated for each CPU. When all Select Enabled to lock the package power limit for the model specific registers. The options is selected, all cores in the CPU will be activated.
  • Page 34 5019S-L User's Manual Chapter 6: BIOS C-State Auto Demotion Chipset Configuration Use this feature to prevent unnecessary excursions into the C-states to improve latency. The Warning: Setting the wrong values in the following features may cause the system to malfunc- options are Disabled, C1, C3, and C1 and C3. tion.
  • Page 35 5019S-L User's Manual Chapter 6: BIOS CPU SLOT7 PCI-E 3.0 X8 DMI/OPI Configuration SLOT7 Max Link Speed The following DMI information will display: Use this item to configure the link speed of a PCI-E port specified by the user. The options •...
  • Page 36 5019S-L User's Manual Chapter 6: BIOS Maximum Memory Frequency PCI Express Configuration Use this feature to set the maximum memory frequency for onboard memory modules. The DMI Link ASPM Control options are Auto, 1067, 1200, 1333, 1400, 1600, 1800, 1867, 2000, 2133, 2200, and 2400. Use this feature to set the ASPM (Active State Power Management) state on the SA (System Max TOLUD Agent) side of the DMI Link.
  • Page 37 5019S-L User's Manual Chapter 6: BIOS SLOT5 PCIe Speed Port 0 ~ Port 7 Spin Up Device (Port 6 and Port 7 on X11SSM-F only) Use this feature to select the PCI Express port speed. The options are Auto, Gen1, Gen2, On an edge detect from 0 to 1, set this item to allow the PCH to initialize the device.
  • Page 38 5019S-L User's Manual Chapter 6: BIOS CPU SLOT 7 PCI-E 3.0 X8 OPROM Super IO Configuration Use this feature to select which firmware type to be loaded for the add-on card in this slot. The following Super IO information will display: The options are Disabled, Legacy, and EFI. •...
  • Page 39 5019S-L User's Manual Chapter 6: BIOS Serial Port 2 Change Settings COM1 Console Redirection Settings This feature specifies the base I/O port address and the Interrupt Request address of a serial This feature allows the user to specify how the host computer will exchange data with the port specified by the user.
  • Page 40 5019S-L User's Manual Chapter 6: BIOS COM1 Recorder Mode COM2 Bits Per second Select Enabled to capture the data displayed on a terminal and send it as text messages to Use this feature to set the transmission speed for a serial port used in Console Redirection. a remote server.
  • Page 41 5019S-L User's Manual Chapter 6: BIOS COM2 Putty KeyPad Flow Control This feature selects Function Keys and KeyPad settings for Putty, which is a terminal emulator Use this item to set the flow control for Console Redirection to prevent data loss caused by designed for the Windows OS.
  • Page 42 5019S-L User's Manual Chapter 6: BIOS iSCSi Configuration Trusted Computing Configuration   iSCSI Initiator Name Security Device Support This feature allows the user to enter the unique name of the iSCSI Initiator in IQN format. If this feature and the TPM jumper on the motherboard are both set to Enabled, onbaord Once the name of the iSCSI Initiator is entered into the system, configure the proper settings security devices will be enabled for TPM (Trusted Platform Module) support to enhance data for the following items.
  • Page 43 5019S-L User's Manual Chapter 6: BIOS PCI Device ID Device Name This item displays the device ID number. This item displays the adapter device name. PCI Address Chip Type This item displays the PCI address for this computer. PCI addresses are 3 two-digit This item displays the network adapter chipset name.
  • Page 44: Event Logs

    5019S-L User's Manual Chapter 6: BIOS 6.4 Event Logs SMBIOS Event Long Standard Settings Log System Boot Event Use this feature to configure Event Log settings. This option toggles the System Boot Event logging to enabled or disabled. The options are Disabled and Enabled.
  • Page 45: Ipmi

    5019S-L User's Manual Chapter 6: BIOS 6.5 IPMI When SEL is Full This feature allows the user to decide what the BIOS should do when the system event log Use this feature to configure Intelligent Platform Management Interface (IPMI) settings. is full.
  • Page 46 5019S-L User's Manual Chapter 6: BIOS Station MAC Address 6.6 Security This item displays the Station MAC address for this computer. Mac addresses are 6 two-digit This menu allows the user to configure the following security settings for the system. hexadecimal numbers.
  • Page 47 5019S-L User's Manual Chapter 6: BIOS Secure Boot Mode Append Key Use this item to select the secure boot mode. The options are Standard and Custom. Select Yes to add the database from the manufacturer's defaults to the existing DB. Select No to load the DB from a file.
  • Page 48 5019S-L User's Manual Chapter 6: BIOS 6.7 Boot • Legacy/UEFI/Dual/Boot Order #8 Use this feature to configure Boot Settings: • Legacy/UEFI/Dual/Boot Order #9 • Legacy/UEFI/Dual/Boot Order #10 • Legacy/UEFI/Dual/Boot Order #11 • Legacy/UEFI/Dual/Boot Order #12 • Legacy/UEFI/Dual/Boot Order #13 • Legacy/UEFI/Dual/Boot Order #14 •...
  • Page 49 5019S-L User's Manual Chapter 6: BIOS 6.8 Save & Exit Default Options Select the Exit tab from the BIOS setup utility screen to enter the Exit BIOS Setup screen. Restore Optimized Defaults To set this feature, select Restore Optimized Defaults from the Save & Exit menu and press <Enter>.
  • Page 50 When BIOS performs the Power On Self Test, it writes checkpoint codes to I/O port 0080h. If the computer cannot complete the boot process, a diagnostic card can be attached to the computer to read I/O port 0080h (Supermicro p/n AOC-LPC80-20). A-1 BIOS Error Beep (POST) Codes For information on AMI updates, please refer to http://www.ami.com/products/.
  • Page 51 Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de Read this appendix in its entirety before installing or configuring components in the Supermicro manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese chassis.
  • Page 52 SuperServer 5019S-L User's Manual Appendix B: Standardized Warning Statements Warnung ‫جسذٌة‬ ‫اصابة‬ ً‫تتسبب ف‬ ‫حالة ٌوكي أى‬ ً‫اًك ف‬ ‫خطز‬ ًٌ‫ٌع‬ ‫هذا الزهز‬ !‫تحذٌز‬ Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen lesen. ‫الذوائز‬ ‫بالوخاطز الٌاجوة عي‬ ‫ي على علن‬...
  • Page 53 SuperServer 5019S-L User's Manual Appendix B: Standardized Warning Statements Power Disconnection Warning Warnung Dieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschluss- bzw. Warning! The system must be disconnected from all sources of power and the power Überstromschutz installiert ist. Stellen Sie sicher, dass der Nennwert der Schutzvorrichtung cord removed from the power supply module(s) before accessing the chassis interior nicht mehr als: 250 V, 20 A beträgt.
  • Page 54 SuperServer 5019S-L User's Manual Appendix B: Standardized Warning Statements Attention ‫امداد‬ ‫وحدة‬ ‫من‬ ‫سهك انكهرباء‬ ‫وإزانت‬ ‫انطاقت‬ ‫مصادر‬ ‫من جميع‬ ‫اننظاو‬ ‫يجب فصم‬ Il est vivement recommandé de confier l'installation, le remplacement et la maintenance de ces équipements à des personnels qualifiés et expérimentés.
  • Page 55 SuperServer 5019S-L User's Manual Appendix B: Standardized Warning Statements Battery Handling Warnung Diese Einheit ist zur Installation in Bereichen mit beschränktem Zutritt vorgesehen. Der Zutritt zu derartigen Bereichen ist nur mit einem Spezialwerkzeug, Schloss und Schlüssel oder einer Warning! There is the danger of explosion if the battery is replaced incorrectly. Replace sonstigen Sicherheitsvorkehrung möglich.
  • Page 56 SuperServer 5019S-L User's Manual Appendix B: Standardized Warning Statements ¡Advertencia! ‫فعليل‬ ‫بطريقة غير صحيحة‬ ‫البطارية‬ ‫انفجار في حالة اسحبذال‬ ‫من‬ ‫هناك خطر‬ Puede que esta unidad tenga más de una conexión para fuentes de alimentación. Para cortar ‫اسحبذال البطارية‬ por completo el suministro de energía, deben desconectarse todas las conexiones.
  • Page 57 SuperServer 5019S-L User's Manual Appendix B: Standardized Warning Statements Backplane Voltage ‫اللىحة‬ ‫أوالطاقة المىجىدة على‬ ‫التيار الكهزبائي‬ ‫مه‬ ‫خطز‬ ‫هناك‬ ‫هذا الجهاس‬ ‫خدمة‬ ‫كه حذرا عند‬ ‫يعمل‬ ‫النظام‬ ‫عندما يكىن‬ Warning! Hazardous voltage or energy is present on the backplane when the system is operating.
  • Page 58 SuperServer 5019S-L User's Manual Appendix B: Standardized Warning Statements ‫תיאום חוקי החשמל הארצי‬ Attention !‫אזהרה‬ La mise au rebut ou le recyclage de ce produit sont généralement soumis à des lois et/ou ‫הציוד חייבת להיות תואמת לחוקי החשמל המקומיים והארציים‬...
  • Page 59 섀시로부터 팬 조립품을 제거할 때 팬은 여전히 회전하고 있을 수 있습니다. 팬 조림품 Verwendung von UL-oder CSA-zertifizierte Kabel, UL oder CSA auf der Code für alle anderen 외관의 열려있는 부분들로부터 손가락 및 스크류드라이버, 다른 물체들이 가까이 하지 elektrischen Geräte als Produkte von Supermicro nur bezeichnet gezeigt haben. 않도록 배치해 주십시오. Waarschuwing ¡Advertencia!
  • Page 60 Het gebruik van andere kabels en adapters kan leiden tot een storing of een brand. Elektrisch apparaat en veiligheidsinformatiebladen wet verbiedt het gebruik van UL of CSA gecertificeerde kabels die UL of CSA die op de code voor andere elektrische apparaten dan de producten die door Supermicro alleen.
  • Page 61 SuperServer 5019S-L User's Manual Appendix C: System Specifications Appendix C Regulatory Compliance Electromagnetic Emissions: FCC Class A, EN 55022 Class A, EN 61000-3-2/3-3, CISPR 22 Class A Electromagnetic Immunity: EN 55024/CISPR 24, (EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN 61000-4-6,...

Table of Contents