Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Supermicro BPN-SAS3-825TQ
Summary of Contents for Supermicro BPN-SAS3-825TQ
- Page 1 BPN-SAS3-825TQ B AckPlANe USeR'S GUIDe 1.0b...
- Page 2 For more information, go to www.P65Warnings.ca.gov. The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency communication devices or other critical systems whose failure to perform be reasonably expected to result in significant injury or loss of life or catastrophic property damage.
-
Page 3: Table Of Contents
Contents Contents Contacting Supermicro ..................iv Returning Merchandise for Service..............v Secure Data Deletion ..................v Chapter 1 Guidelines ESD Safety Guidelines ................... 1-1 General Safety Guidelines ................1-1 Version Information ..................1-2 Chapter 2 Connectors, Jumpers, and LEDs Rear Connector Locations ................2-1 Rear Connector Definitions ................ -
Page 4: Contacting Supermicro
BPN-SAS3-825TQ Backplane Manual Contacting Supermicro Headquarters Address: Super Micro Computer, Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. Tel: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.com (Technical Support) Web Site: www.supermicro.com Europe Address: Super Micro Computer B.V. -
Page 5: Returning Merchandise For Service
For faster service, RMA authorizations may be requested online (http://www. supermicro.com/support/rma/). Whenever possible, repack the backplane in the original Supermicro box, using the original packaging materials. If these are no longer available, be sure to pack the backplane in an anti-static bag and inside the box. Make sure that there is enough packaging material surrounding the backplane so that it does not become damaged during shipping. - Page 6 BPN-SAS3-825TQ Backplane Manual Notes...
-
Page 7: Chapter 1 Guidelines
Chapter 1 Guidelines This chapter offers guidelines for personal and equipment safety, and notes about the BPN-SAS3-825TQ version documented in this manual. ESD Safety Guidelines Electrostatic Discharge (ESD) can damage electronic com ponents. To prevent damage to your system, it is important to handle it very carefully. The following measures are generally sufficient to protect your equipment from ESD. -
Page 8: Version Information
BPN-SAS3-825TQ Backplane Manual Version Information The BPN-SAS3-825TQ backplane has been designed to utilize the most up-to-date technology available, providing your system with reliable, high-quality performance. This manual reflects PCB Revision 2.00A, the most current release available at the time of publication. Refer to the Supermicro Web site at www.supermicro.com for... -
Page 9: Chapter 2 Connectors, Jumpers, And Leds
Chapter 2 Connectors, Jumpers, and LEDs Chapter 2 Connectors, Jumpers, and LEDs This manual describes the BPN-SAS3-825TQ backplane, which supports SAS3 and SATA3 drives. Rear Connector Locations The following connectors are on the side of the backplane that faces the rear of the chassis. -
Page 10: 2-2 Rear Connector Definitions
BPN-SAS3-825TQ Backplane Manual 2-2 Rear Connector Definitions 1. Backplane Main Power Connectors Main Power 4-Pin Connector The 4-pin connectors, designated JP10 Pin# Definition and JP13, provide power to the backplane. +12V 2 and 3 Ground 2. CD/Floppy Drive Pin Connectors CD/FDD Power... - Page 11 Chapter 2 Connectors, Jumpers, and LEDs 6, 7. Sideband Headers Sideband Headers The sideband headers are designated JP51 Pin # Definition Pin # Definition and JP52. For SES-2 to work properly, you SGPIO: Controller must connect an 8-pin sideband cable. SDIN;...
-
Page 12: Rear Jumpers
BPN-SAS3-825TQ Backplane Manual Rear Jumpers JP43 ACT_IN ACT_IN SIDEBAND #2 SIDEBAND #2 +12V +12V +12V +12V JP36 JP29 SAS825TQ SAS825TQ JP18 REV 2.0 REV 2.0 BAR CODE BAR CODE JP50 JP38 JP37 JP33 JP34 JP29:9072 RESET JP29:9072 RESET SIDEBAND #1... -
Page 13: Sgpio And I C Modes And Jumper Settings
Chapter 2 Connectors, Jumpers, and LEDs SGPIO and I C Modes and Jumper Settings This backplane can utilize SGPIO or I C. SGPIO is the default mode and can be used without making changes to your jumpers. The following tables describe jumper settings for each mode. -
Page 14: Rear Led Indicators
BPN-SAS3-825TQ Backplane Manual Rear LED Indicators ACT_IN ACT_IN SIDEBAND #2 SIDEBAND #2 +12V +12V +12V +12V SAS825TQ SAS825TQ REV 2.0 REV 2.0 BAR CODE BAR CODE JP29:9072 RESET JP29:9072 RESET SIDEBAND #1 SIDEBAND #1 Figure 2-4. Front LED LEDs State... -
Page 15: Front Connectors And Led Indicators
Chapter 2 Connectors, Jumpers, and LEDs Front Connectors and LED Indicators The side of the backplane facing the front of the chassis provides connectors for eight SAS3 drives, and LEDs showing activity or failure.. ACT6 ACT4 ACT5 ACT7 FAIL6 FAIL4 FAIL5 FAIL7 SAS#4... - Page 16 BPN-SAS3-825TQ Backplane Manual Disclaimer (cont.) The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency communication devices or other critical systems whose failure to perform be reasonably expected to result in significant injury or loss of life or catastrophic property damage.
Need help?
Do you have a question about the BPN-SAS3-825TQ and is the answer not in the manual?
Questions and answers