National Instruments SCXI-1000 Quick Start Manual

National Instruments SCXI-1000 Quick Start Manual

Hide thumbs Also See for SCXI-1000:
Table of Contents

Advertisement

Available languages

Available languages

Quick Links

SCXI Quick Start Guide
Signal Conditioning eXtensions for Instrumentation
Contents
National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation. Refer to the Terms of Use section on
ni.com/legal for more information about National Instruments trademarks. Other product and company names mentioned herein are
trademarks or trade names of their respective companies. For patents covering National Instruments products, refer to the appropriate location:
Help»Patents in your software, the patents.txt file on your CD, or ni.com/patents.
373236E-01
This document explains how to install and configure SCXI signal
conditioning modules in SCXI-1000, SCXI-1001, SCXI-1000DC, or
PXI/SCXI combination chassis, confirm the module and chassis are
operating properly, and set up multichassis systems. It also describes the
NI-DAQ 7.x software relative to SCXI and integrated signal conditioning
products. This document assumes you have already installed, configured,
and tested the data acquisition (DAQ) device to which you will connect the
SCXI module. If you have not, refer to the DAQ Quick Start Guide included
with the DAQ device, and available on the NI-DAQ 7.x Device
Documentation CD and from
This document does not cover installing and configuring SCXI switch
modules. If you are installing an SCXI switch, refer to the NI Switches
Getting Started Guide.
Conventions ............................................................................................ 2
Step 2. Verify the Components ............................................................... 4
Step 3. Set Up the Chassis ...................................................................... 5
SCXI Chassis ................................................................................... 5
PXI/SCXI Combination Chassis...................................................... 5
Step 4. Install the Modules...................................................................... 6
PXI/SCXI Combination Chassis...................................................... 6
SCXI Chassis ................................................................................... 7
SCXI USB Modules......................................................................... 8
Adding a Module to an Existing SCXI System ............................... 8
Step 5. Attach Sensors and Signal Lines................................................. 9
Step 6. Attach the Terminal Blocks ........................................................ 10
SCXI Chassis or PXI/SCXI Combination Chassis .......................... 10
Step 7. Install the Cable Adapter ............................................................ 11
Single-Chassis System ..................................................................... 11
Multichassis System ........................................................................ 12
Step 8. Connect the Modules to the DAQ Device .................................. 13
Single-Chassis System ..................................................................... 13
Multichassis System ........................................................................ 14
Step 9. Power On the SCXI Chassis ....................................................... 15
© 2003-2005 National Instruments Corp. All rights reserved.
, before continuing.
ni.com/manuals
February 2005

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SCXI-1000 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for National Instruments SCXI-1000

  • Page 1: Table Of Contents

    Step 9. Power On the SCXI Chassis ............15 National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation. Refer to the Terms of Use section on ni.com/legal for more information about National Instruments trademarks. Other product and company names mentioned herein are trademarks or trade names of their respective companies.
  • Page 2: Conventions

    Step 10. Launch Measurement & Automation Explorer (MAX) ....15 Step 11. Confirm That the Chassis and Modules Are Recognized ..15 Step 12. Add the Chassis .................16 Identify the PXI Controller...............16 Add the SCXI Chassis in NI-DAQmx..........17 Add the SCXI Chassis in Traditional NI-DAQ (Legacy) ....17 Step 13.
  • Page 3: Step 1. Unpack The Chassis, Module, And Accessories

    NI-DAQ 7.x Device Documentation CD in the NI-DAQ software kit or at . After you install ni.com/support the Device Document Browser, device documents are accessible from Start»Programs»National Instruments»NI-DAQ»Browse Device Documentation. © National Instruments Corporation SCXI Quick Start Guide...
  • Page 4: Step 2. Verify The Components

    Step 2. Verify the Components Make sure you have the SCXI system components shown in Figure 1. ® W ER 1 Terminal Block or TBX Accessories (optional) 7 For SCXI Chassis Only 2 PXI Module 8 Chassis Adapter Assembly 3 SCXI Modules 9 DAQ Device 4 PXI/SCXI Combination Chassis with Controller 10 USB Cable...
  • Page 5: Step 3. Set Up The Chassis

    A system controller must be installed in the PXI side of the chassis. Refer to and type for more information on ordering a configured PXI/SCXI ni.com/info rdfis5 combination chassis through Factory Installation Services. © National Instruments Corporation SCXI Quick Start Guide...
  • Page 6: Step 4. Install The Modules

    Power off both the PXI and SCXI power switches, and unplug the chassis. Set the SCXI address switches positions to off. In Figure 3, all switches are shown in the off position. Set the voltage selection tumbler to the correct voltage for your application.
  • Page 7: Scxi Chassis

    Insert the module into the SCXI slot. Secure the module to the chassis front panel mounting rail using the two thumbscrews. ® 1 Thumbscrews 2 Module Figure 5. Installing the SCXI Module in a New Chassis © National Instruments Corporation SCXI Quick Start Guide...
  • Page 8: Scxi Usb Modules

    SCXI USB Modules Note SCXI USB modules, such as the SCXI-1600, cannot be used in a PXI/SCXI combination chassis or in multichassis systems. SCXI USB modules are plug-and-play, integrated signal conditioning modules that communicate between an SCXI system and a USB-compatible computer or USB hub, so no intermediate DAQ device is needed.
  • Page 9: Step 5. Attach Sensors And Signal Lines

    Switch or jumper settings—Refer to the module user manual for more information about configuring the hardware. • Sensors: – Refer to ni.com/sensors – If you are using LabVIEW, refer to the LabVIEW Measurements Manual packaged with LabVIEW or available from ni.com/manuals © National Instruments Corporation SCXI Quick Start Guide...
  • Page 10: Step 6. Attach The Terminal Blocks

    If you are using Traditional NI-DAQ (Legacy), refer to Chapter 5, Transducer Conversion Functions, of the Traditional NI-DAQ User Manual, which you can access from Start»Programs» National Instruments»NI-DAQ»Traditional NI-DAQ User Manual. – For information on IEEE 1451.4 TEDS smart sensors, refer to ni.com/zone...
  • Page 11: Step 7. Install The Cable Adapter

    Do not force the adapter if there is resistance. Forcing the adapter can bend pins. Caution Fasten the adapter to the rear of the SCXI chassis with the screws provided with the SCXI-1349. © National Instruments Corporation SCXI Quick Start Guide...
  • Page 12: Multichassis System

    1 SCXI Chassis 3 68-Pin Shielded Cable 2 SCXI-1349 Cable Adapter 4 Screws Figure 9. Installing the Cable Adapter Multichassis System The SCXI-1346 covers the rear connector of two modules. The module to the right Note of the one directly connected to the SCXI-1346 cannot have an external cable inserted into its rear 50-pin connector.
  • Page 13: Step 8. Connect The Modules To The Daq Device

    1 SCXI-1000 or SCXI-1001 Chassis 2 SCXI-1346 Cable Adapter 3 Shielded Cable Connecting to TO NEXT CHASSIS 4 Shielded Cable Connecting to FROM DAQ BOARD OR PREVIOUS CHASSIS Figure 10. SCXI-1346 Cable Assembly Install the SCXI-1349 cable adapter into the last SCXI chassis in the chain.
  • Page 14: Multichassis System

    Multichassis System Connect either end of one 68-pin shielded cable to the E Series DAQ device. Connect the other end of the cable to the SCXI-1346 in chassis ID n labeled FROM DAQ BOARD OR PREVIOUS CHASSIS. Connect a 68-pin shielded cable to the SCXI-1346 in chassis n labeled TO NEXT CHASSIS.
  • Page 15: Step 9. Power On The Scxi Chassis

    Expand Devices and Interfaces. If you are using a remote RT target, expand Remote Systems, find and expand your target, and then expand Devices and Interfaces. Check that your device appears under Devices and Interfaces. © National Instruments Corporation SCXI Quick Start Guide...
  • Page 16: Step 12. Add The Chassis

    1 When a device is supported by both Traditional NI-DAQ (Legacy) and NI-DAQmx and both are installed, the same device is listed with a different name under the Traditional NI-DAQ (Legacy) and NI-DAQmx folders under My System»Devices and Interfaces. 2 Only NI-DAQmx devices are listed under Remote Systems»Devices and Interfaces.
  • Page 17: Add The Scxi Chassis In Ni-Daqmx

    Right-click Devices and Interfaces and select Create New. Alternatively, right-click Devices and Interfaces»Traditional NI-DAQ (Legacy) Devices and select Add SCXI Chassis. The Create New window opens. Select the SCXI chassis under Traditional NI-DAQ (Legacy) Devices. Click Finish. © National Instruments Corporation SCXI Quick Start Guide...
  • Page 18: Step 13. Configure The Chassis And Modules

    Step 13. Configure the Chassis and Modules The configuration process differs depending on the NI-DAQ API you are using to control the chassis and modules—NI-DAQmx or Traditional NI-DAQ (Legacy). Configure the Chassis and Modules in NI-DAQmx If you are configuring a chassis with an SCXI-1600, right-click the chassis, select Note Properties, and skip to step 6 of this section.
  • Page 19 If you are using a connected accessory, specify it in Accessory. Click Details. The Details window opens. 10. If you are configuring an SCXI module with jumper-selectable settings, click the Jumpers tab and enter the hardware-selected settings. © National Instruments Corporation SCXI Quick Start Guide...
  • Page 20 11. Click the Accessory tab. Select a compatible module accessory from the Accessory drop-down listbox. 12. Click Configure to edit accessory settings. Not all accessories have settings. Refer to the accessory documentation for more information. 13. If you are using an analog input module in parallel mode, in a multichassis configuration, or another special configuration, click the Cabling tab to adjust the settings for cabling.
  • Page 21 18. If you installed more than one module, repeat the process from step 6 of this procedure. 19. If you need to change any chassis settings, click the Chassis tab. 20. Click OK to accept and save the settings for this chassis. © National Instruments Corporation SCXI Quick Start Guide...
  • Page 22: Add Modules To An Existing System In Ni-Daqmx

    A message at the top of the SCXI Chassis Configuration window displays the status of the configuration. You cannot save the chassis configuration if an error appears until you finish entering module information. If a warning appears, you can save the configuration, but NI recommends that you correct the source of the warning first.
  • Page 23 Complete the following steps to configure the module in a local system using Traditional NI-DAQ (Legacy). Expand Devices and Interfaces»Traditional NI-DAQ (Legacy) Devices. Expand the chassis to display a list of modules. Right-click a module slot and choose Properties. © National Instruments Corporation SCXI Quick Start Guide...
  • Page 24 The Configuring SCXI Module in Chassis Slot window opens. The General tab is selected by default. Choose the DAQ device connected to the module from the Connected to list. Select the checkbox if the DAQ device controls the chassis. Select a mode—multiplexed or parallel—from Operating Mode. If you are using modules with software-selectable filters and/or gain settings for each channel, click the Channel tab and select the settings.
  • Page 25: Add Modules To An Existing Local System In Traditional Ni-Daq (Legacy)

    For information about the software-configurable properties of the module, refer to Measurement & Automation Explorer Help for Traditional NI-DAQ. In MAX, select Help»Help Topics»Traditional NI-DAQ (Legacy). Select a compatible device from the Accessory list. Click Finish. © National Instruments Corporation SCXI Quick Start Guide...
  • Page 26: Step 14. Test The Chassis

    Step 14. Test the Chassis Expand Devices and Interfaces»NI-DAQmx Devices or Devices and Interfaces»Traditional NI-DAQ (Legacy) Devices. Testing a chassis on a remote RT target is not supported in Traditional NI-DAQ (Legacy). Right-click the name of the chassis to test. Select Test to verify that MAX recognizes the chassis.
  • Page 27: Step 15. Configure Channels And Tasks

    – Connect the DAQ device to a different module in the chassis. – Try a different cable assembly. – Try a different chassis. – Try a different DAQ device. © National Instruments Corporation SCXI Quick Start Guide...
  • Page 28: Resources

    I am not getting good data on any channel. What is causing this problem? The SCXI chassis has backplane fuses, fused at 1.5 A on the SCXI-1000 chassis and at 4 A on the SCXI-1001 chassis. One or both of the fuses might be blown.
  • Page 29 Verify correct placement and configuration of the modules. If you did not auto-detect modules, modules installed in the chassis may not be configured in software. Alternately, modules configured in software might not match the ones installed in the chassis. © National Instruments Corporation SCXI Quick Start Guide...
  • Page 30 Can I programmatically detect whether or not my chassis is powered on? You can determine whether or not you can communicate with configured modules. In NI-DAQmx, use a LabVIEW VI that you can obtain from by typing or in Traditional NI-DAQ (Legacy), ni.com/express rdtscp, SCXI_ModuleID_Read...
  • Page 31: Worldwide Technical Support

    Worldwide Technical Support Visit the following sections of the National Instruments Web site at for technical support and professional services: ni.com • Support—Online technical support resources at ni.com/support include the following: – Self-Help Resources—For answers and solutions, visit the award-winning National Instruments Web site for software drivers...
  • Page 32: Specifications

    Specifications Safety These products are designed to meet the requirements of the following standards of safety for electrical equipment for measurement, control, and laboratory use: • IEC 61010-1, EN-61010-1 • UL61010-1 • CAN/CSA-C22.2 No. 1010-1 Note For UL and other safety certifications, refer to the product label or visit , search by model number or product line, and click the ni.com/certification appropriate link in the Certification column.
  • Page 33 Système à un seul châssis ..............47 National Instruments, NI, ni.com et LabVIEW sont des marques de National Instruments Corporation. Pour plus d’informations concernant les marques de National Instruments, veuillez vous référer à la partie Terms of Use sur le site .
  • Page 34: Conventions

    Système multi-châssis ..............47 Étape 9. Mettez le châssis SCXI sous tension .........48 Étape 10. Ouvrez Measurement & Automation Explorer (MAX) ..49 Étape 11. Confirmez que le châssis et les modules ont été reconnus ..49 Étape 12. Ajoutez le châssis ..............50 Identifier le contrôleur PXI ..............50 Ajouter le châssis SCXI dans NI-DAQmx........51 Ajouter le châssis SCXI dans...
  • Page 35: Étape 1. Déballez Le Châssis, Le Module Et Les Accessoires

    Sortez le châssis, le module et l’accessoire de son sachet d’emballage et examinez les produits pour repérer tout composant déconnecté ou tout signe d’endommagement. Contactez NI si l’un des produits apparaît endommagé de quelque façon que ce soit. N’installez pas un périphérique endommagé. © National Instruments Corporation Guide de démarrage SCXI...
  • Page 36: Étape 2. Vérifiez Les Composants

    . Une fois que ni.com/support vous aurez installé l’explorateur Device Document Browser, vous pourrez accéder aux documents du périphérique à partir de Démarrer» Programmes»National Instruments»NI-DAQ»Browse Device Documentation. Étape 2. Vérifiez les composants Assurez-vous que vous avez les composants du système SCXI représentés dans la figure 1.
  • Page 37: Étape 3. Configurez Le Châssis

    AC différents. Reportez-vous à la documentation du châssis pour obtenir de plus amples informations. Vérifiez que les paramètres d’alimentation sont correctement définis (100, 120, 220 ou 240 VAC). Connectez le cordon d’alimentation. © National Instruments Corporation Guide de démarrage SCXI...
  • Page 38: Châssis Combiné Pxi/Scxi

    ® 1 2 0 RESET 1 Avant 3 Interrupteur d’alimentation du châssis 5 Culbuteur de sélection de tension 2 Arrière 4 Interrupteur d’adresse du châssis 6 Prise du cordon d’alimentation Figure 2. Configuration du châssis SCXI Châssis combiné PXI/SCXI Remarque Un contrôleur système doit être installé...
  • Page 39: Étape 4. Installez Les Modules

    Faites glisser le module vers l’arrière du châssis. Vérifiez que la poignée d’insertion/éjection est abaissée. Dès que vous sentez une résistance, relevez la poignée d’insertion/éjection pour insérer complètement le module en place. © National Instruments Corporation Guide de démarrage SCXI...
  • Page 40: Châssis Scxi

    Fixez le module sur le rail de montage de la face-avant du châssis à l’aide des deux vis. 1 Module DAQ PXI 3 Rail d’insertion/éjection 2 Poignée d’insertion/éjection Figure 4. Installation du module PXI dans un nouveau châssis Châssis SCXI Touchez n’importe quelle partie métallique du châssis pour décharger l’électricité...
  • Page 41: Modules Usb Scxi

    Reportez-vous à la liste des modules SCXI à l’Étape 7. Installez l’adaptateur de câble pour déterminer quel module doit être connecté à l’adaptateur de câble, le cas échéant. © National Instruments Corporation Guide de démarrage SCXI...
  • Page 42: Étape 5. Connectez Les Lignes De Capteurs Et De Signaux

    1 Nouveau module SCXI 3 Châssis SCXI 2 Module SCXI existant 4 Périphérique DAQ existant Figure 7. Installation du module SCXI dans un système existant Étape 5. Connectez les lignes de capteurs et de signaux Connectez les lignes de capteurs et de signaux aux blocs de connexion, aux terminaux accessoires ou aux terminaux du module.
  • Page 43: Étape 6. Connectez Les Blocs De Terminaison

    Placez les blocs de connexion sur l’avant des modules. Reportez-vous à la page pour connaître les combinaisons de modules et ni.com/products blocs de connexion possibles. Reportez-vous au guide d’installation TBX si vous utilisez un bloc de terminaison TBX. © National Instruments Corporation Guide de démarrage SCXI...
  • Page 44: Étape 7. Installez L'adaptateur De Câble

    ® 1 Modules avec blocs de terminaison installés 2 Connexion d’un bloc de terminaison au module SCXI 3 Faces-avant de modules SCXI Figure 8. Connexion de blocs de terminaison Étape 7. Installez l’adaptateur de câble Système à un seul châssis Remarque Si vous installez un module USB SCXI, comme le SCXI-1600, ou que vous utilisez un châssis combiné...
  • Page 45: Système Multi-Châssis

    Le SCXI-1346 couvre le connecteur arrière de deux modules. Il n’est pas possible de brancher un câble externe dans le connecteur à 50 broches du module se trouvant sur le côté droit du module qui est directement connecté au SCXI-1346. © National Instruments Corporation Guide de démarrage SCXI...
  • Page 46 Répétez les étapes 1 à 3 pour chaque châssis SCXI dans le système, à l’exception du dernier châssis SCXI dans la chaîne. 1 Châssis SCXI-1000 ou SCXI-1001 2 Adaptateur de câble SCXI-1346 3 Câble blindé se connectant à TO NEXT CHASSIS 4 Câble blindé...
  • Page 47: Étape 8. Connectez Les Modules Au Périphérique Daq

    Connectez le câble blindé à 68 broches à l’avant-dernier châssis dans l’emplacement étiqueté TO NEXT CHASSIS. Connectez l’autre extrémité du câble au SCXI-1349 dans le dernier châssis. © National Instruments Corporation Guide de démarrage SCXI...
  • Page 48: Étape 9. Mettez Le Châssis Scxi Sous Tension

    – – – 1 Câble blindé connecté à l’adaptateur de câble SCXI-1349 5 Blocs de terminaison 2 Câble blindé connecté à l’adaptateur de câble SCXI-1346 6 Capteurs 3 Périphérique DAQ 7 Châssis SCXI 4 Câble blindé au périphérique DAQ Figure 11. Système SCXI complété Étape 9.
  • Page 49: Étape 10. Ouvrez Measurement & Automation Explorer (Max)

    Développez la catégorie Périphériques et interfaces. Si vous utilisez une cible RT déportée, développez l’élément Systèmes déportés, recherchez et développez votre cible, et développez ensuite la catégorie Périphériques et interfaces. Vérifiez que votre périphérique apparaît bien sous Périphériques et interfaces. © National Instruments Corporation Guide de démarrage SCXI...
  • Page 50: Étape 12. Ajoutez Le Châssis

    1 Quand un périphérique est supporté à la fois par NI-DAQ traditionnel (ancien driver) et NI-DAQmx et que ces deux drivers sont installés, le même périphérique apparaît sous un nom différent dans les dossiers NI-DAQ traditionnel et NI-DAQmx sous Système»Périphériques et interfaces. 2 Seuls les périphériques NI-DAQmx sont recensés sous Systèmes déportés»...
  • Page 51: Ajouter Le Châssis Scxi Dans Ni-Daqmx

    Châssis SCXI NI-DAQmx. Cliquez sur Terminer. Vous pouvez aussi faire un clic droit sur Périphériques et interfaces» Périphériques NI-DAQmx et sélectionner le châssis à partir de Créer un nouvel objet»Châssis SCXI NI-DAQmx. © National Instruments Corporation Guide de démarrage SCXI...
  • Page 52: Ajouter Le Châssis Scxi Dans Ni-Daq Traditionnel (Ancien Driver)

    Ajouter le châssis SCXI dans NI-DAQ traditionnel (ancien driver) Effectuez les étapes suivantes pour ajouter le châssis à un système local en utilisant NI-DAQ traditionnel (ancien driver). Cliquez avec le bouton droit sur Périphériques et interfaces et sélectionnez Créer un nouvel objet. Vous pouvez aussi faire un clic droit sur Périphériques et interfaces»Périphériques NI-DAQ traditionnel (ancien driver) et sélectionner Ajouter un châssis SCXI.
  • Page 53 état inconnu ou indésirable. Déconnectez tous les périphériques connectés pour lesquels une détection automatique pourrait poser un problème. Cliquez sur Enregistrer. La fenêtre Configuration d’un châssis SCXI s’ouvre. L’onglet Modules est sélectionné par défaut. © National Instruments Corporation Guide de démarrage SCXI...
  • Page 54 Si vous n’avez pas sélectionné la détection automatique des modules, sélectionnez un module SCXI dans la liste déroulante Modules. Assurez-vous que le module correspond au bon emplacement. Cliquez dans le champ Identificateur de périphérique et entrez un ID alphanumérique unique pour changer le nom du module SCXI. MAX fournit un nom par défaut pour Identificateur de périphérique.
  • Page 55 Câblage pour ajuster les paramètres de câblage. Si vous exploitez le module en mode multiplexé standard, il n’est pas nécessaire de modifier ces paramètres. © National Instruments Corporation Guide de démarrage SCXI...
  • Page 56 14. Sélectionnez le périphérique DAQ connecté au module SCXI dans la liste Quel est le périphérique connecté à ce module ?. 15. Sélectionnez un périphérique DAQ dans la liste Numériseur de module. • En mode multiplexé, vous pouvez sélectionner un autre module comme numériseur de module.
  • Page 57: Ajouter Des Modules À Un Système Existant Dans Ni-Daqmx

    Cliquez sur Auto-détecter tous les modules et sur Oui. En commençant à l’étape 6 de la section précédente, suivez les instructions pour configurer le module. Testez le châssis, comme décrit à l’Étape 14. Testez le châssis. © National Instruments Corporation Guide de démarrage SCXI...
  • Page 58: Configurer Le Châssis Et Les Modules Dans Ni-Daq Traditionnel (Ancien Driver)

    Configurer le châssis et les modules dans NI-DAQ traditionnel (ancien driver) Effectuez les étapes suivantes, comme illustré dans les figures, pour configurer un châssis SCXI local dans NI-DAQ traditionnel (ancien driver). Sélectionnez un ID pour le châssis SCXI. L’ID peut prendre n’importe quelle valeur entière entre 1 et 3200.
  • Page 59 Développez la catégorie Périphériques et interfaces»Périphériques NI-DAQ traditionnel (ancien driver). Développez le châssis pour afficher la liste des modules. Cliquez avec le bouton droit sur un emplacement de module et sélectionnez Propriétés. © National Instruments Corporation Guide de démarrage SCXI...
  • Page 60 La fenêtre de configuration d’un module SCXI dans un emplacement du châssis s’affiche. L’onglet Généralités est sélectionné par défaut. Sélectionnez le périphérique DAQ connecté au module dans la liste Connecté à. Cochez la case située en dessous si le périphérique DAQ contrôle le châssis.
  • Page 61: Ajouter Des Modules À Un Système Local Existant Dans Ni-Daq Traditionnel (Ancien Driver)

    Développez le châssis pour afficher la liste des emplacements. Faites un clic droit sur un emplacement vide et sélectionnez Insérer. Sélectionnez le module SCXI que vous voulez ajouter au châssis. Cliquez sur Suivant. Aucun est sélectionné par défaut pour Connecté à. © National Instruments Corporation Guide de démarrage SCXI...
  • Page 62: Étape 14. Testez Le Châssis

    Sélectionnez le mode : multiplexé ou parallèle, dans Mode de fonctionnement. Cliquez sur Suivant. Si vous utilisez des modules comportant des filtres sélectionnables au niveau du logiciel et/ou des paramètres de gain pour chaque voie, définissez les valeurs de ces paramètres pour chaque voie. Sélectionnez les paramètres dans les différents champs affichés.
  • Page 63: Étape 15. Configurez Les Voies Et Les Tâches

    Configurez les voies et les tâches du Guide de démarrage DAQ pour plus de précisions. Conseils pour le développement d’une application Reportez-vous au Guide de démarrage DAQ pour obtenir des informations. © National Instruments Corporation Guide de démarrage SCXI...
  • Page 64: Dépannage

    Dépannage Cette section contient des conseils de dépannage ainsi que les réponses aux questions les plus fréquemment posées par les utilisateurs SCXI au personnel du service de support technique de NI. Conseils Avant de contacter NI, essayez les suggestions de dépannage suivantes : •...
  • Page 65: Questions Fréquemment Posées

    Quelle peut être l’origine du problème ? Le châssis SCXI est équipé de fusibles sur le fond de panier, capables de supporter 1,5 A pour le châssis SCXI-1000 et 4 A pour le châssis SCXI-1001. Il est possible qu’un des deux fusibles, ou les deux, soient grillés.
  • Page 66 Si le problème persiste après remplacement du fusible, il est possible que vous ayez endommagé le circuit du bus numérique ou le module SCXI. Veuillez contacter le support technique National Instruments à l’adresse pour obtenir de l’aide. ni.com/support MAX ne reconnaît pas le châssis lorsque je lance un test.
  • Page 67 SCXI à la terre. Vérifiez que vous avez mis à la masse le connecteur négatif de chaque thermocouple flottant par l’intermédiaire d’une résistance. © National Instruments Corporation Guide de démarrage SCXI...
  • Page 68: Support Technique Dans Le Monde Entier

    élevée en mode commun sur la référence de masse du thermocouple. Support technique dans le monde entier Visitez les sections suivantes du site Web de National Instruments sur pour obtenir une assistance technique et des services ni.com professionnels : •...
  • Page 69: Spécifications

    Certificat d’étalonnage : si votre produit supporte l'étalonnage, vous pouvez obtenir un certificat d’étalonnage sur ni.com/calibration Le siège social de National Instruments est situé à cette adresse : 11500 North Mopac Expressway, Austin, Texas, 78759-3504, États-Unis. Visitez la section sur les filiales internationales, sur ni.com/niglobal...
  • Page 70: Conformité Ce

    Pour assurer sa conformité EMC, exploitez ce périphérique avec des câbles Remarque blindés. Conformité CE Ces produits remplissent les principales conditions des Directives européennes applicables, telles que modifiées pour l'estampille CE, comme suit : Directive portant sur les basses tensions (sécurité) ..........73/23/EEC Directive portant sur la compatibilité...
  • Page 71 Systeme mit nur einem Chassis ............82 Multichassis-System ..............84 National Instruments, NI, ni.com und LabVIEW sind Marken der Firma National Instruments Corporation. Nähere Informationen zu den Marken von National Instruments finden Sie im Abschnitt Terms of Use unter . Sonstige hierin erwähnte Produkt- und Firmenbezeichnungen sind ni.com/legal...
  • Page 72: Symbole Und Darstellungen

    Schritt 8: Anschließen der Module an die DAQ-Karte ....... 85 Systeme mit nur einem Chassis............ 85 Multichassis-System..............86 Schritt 9: Einschalten des Chassis ............87 Schritt 10: Starten des Measurement & Automation Explorer (MAX) ................87 Schritt 11: Überprüfung der automatischen Erkennung des Chassis und der Module.................
  • Page 73 Dateinamen und Zeichen dargestellt, die im jeweiligen Fall über die Tastatur einzugeben sind. Mit Monospace-Schrift im Fettdruck sind auf dem Bildschirm ausgegebene monospace fett Meldungen gekennzeichnet. Außerdem finden Sie in dieser Darstellungsart Befehlszeilen, die sich von anderen Beispielen unterscheiden. © National Instruments Corporation SCXI-Schnellstartanleitung...
  • Page 74: Schritt 1: Auspacken Der Chassis, Module Und Des Zubehörs

    Schritt 1: Auspacken der Chassis, Module und des Zubehörs Ihr Modul ist antistatisch verpackt, um Schäden durch elektrostatische Ent- ladung zu verhindern. Vorsicht! Freiliegende Kontakte niemals mit den Fingern berühren! Ergreifen Sie beim Auspacken folgende Vorsichtsmaßnahmen: • Legen Sie sich ein Erdungskabel an oder berühren Sie ein mit Masse verbundenes Objekt.
  • Page 75: Schritt 2: Überprüfen Der Komponenten Auf Vollständigkeit

    Mindestens eines der folgenden Softwarepakete einschließlich der dazugehörigen Dokumentation: – LabVIEW ™ ™ – LabWindows /CVI – Visual C++ – Visual Basic • Betriebsanleitungen der SCXI-Module • Schraubendreher, etwa 3 mm breit • Phillips-Schraubendreher 1 und 2 © National Instruments Corporation SCXI-Schnellstartanleitung...
  • Page 76: Schritt 3: Inbetriebnahme Des Chassis

    • Abisoliergerät • Spitzzange Schritt 3: Inbetriebnahme des Chassis Lesen Sie bitte vor dem Entfernen von Abdeckungen oder Kabeln das Faltblatt Vorsicht! Read Me First: Safety and Radio-Frequency Interference, das Ihrem Chassis beiliegt. Vor Installation der Karte ist unbedingt eine Erdung erforderlich, um Schäden durch elektro- statische Entladung vorzubeugen.
  • Page 77: Pxi/Scxi-Kombinations-Chassis

    Lesen Sie bitte für weitere Hinweise die Beschreibung des ent- sprechenden Chassis. Schließen Sie das Netzkabel an. 1 2 0 RESET 1 Vorderseite 4 Netzkabelanschluss 7 PXI-Netzschalter 2 Rückseite 5 Adressschalter 8 Systemcontroller 3 Spannungregler 6 SCXI-Netzschalter Abbildung 3. Aufbau eines PXI/SCXI-Kombinations-Chassis © National Instruments Corporation SCXI-Schnellstartanleitung...
  • Page 78: Schritt 4: Einstecken Der Module

    Schritt 4: Einstecken der Module Das Chassis muss unbedingt ausgeschaltet sein. SCXI-Module können nicht bei Vorsicht! laufendem Betrieb ausgetauscht werden, da sonst die Sicherungen durchbrennen oder das Chassis bzw. die Module beschädigt werden können. PXI/SCXI-Kombinations-Chassis Um das PXI-DAQ-Modul der E- oder M-Serie, über das der Datenaus- tausch zwischen Chassis und PC erfolgen soll, in den PXI-Steckplatz (ganz rechts) einzubauen, gehen Sie wie folgt vor: Berühren Sie zur elektrostatischen Entladung ein beliebiges Metallteil...
  • Page 79: Scxi-Chassis

    DAQ-Karte erforderlich ist. Verfahren Sie nach dem Einstecken des Moduls in das Chassis wie folgt: Schließen Sie das Modul mit dem USB-Kabel an den Computer oder einen anderen damit verbundenen Hub an. Befestigen Sie mit einem Kabelbinder die Zugentlastungsvorrichtung am Kabel. © National Instruments Corporation SCXI-Schnellstartanleitung...
  • Page 80: Hinzufügen Von Modulen Zu Einem Scxi-System

    ® oder 1 PC 3 USB-Kabel 2 USB-Hub 4 SCXI-Modul mit USB-Anschluss ß Abbildung 6. Anschlie en eines SCXI-Moduls mit USB-Anschluss Hinzufügen von Modulen zu einem SCXI-System Module können auch in SCXI-Systeme eingesteckt werden, die im Multi- plexmodus betrieben werden. Sollte es in Ihrem System bereits einen Controller geben, stecken Sie alle weiteren Module einfach wie beschrie- ben in die verbleibenden Steckplätze.
  • Page 81: Schritt 5: Anschließen Der Sensoren Und Leitungen

    Zum traditionellen NI-DAQ-Treiber (alt) im Kapitel 5, Transducer Conversion Functions, des Traditional NI-DAQ User Manual, zu finden unter Start»Programme»National Instruments»NI-DAQ»Traditional NI-DAQ User Manual. – Auf unserer Website zu TEDS-Sensoren (intelli- ni.com/zone genten Sensoren, die dem Standard IEEE 1451.4 entsprechen). © National Instruments Corporation SCXI-Schnellstartanleitung...
  • Page 82: Schritt 6: Befestigen Der Anschlussblöcke

    Schritt 6: Befestigen der Anschlussblöcke SCXI-Chassis oder PXI/SCXI-Kombinations-Chassis Bei Nutzung eines Moduls, das direkt an den PC angeschlossen wird, fahren Sie Hinweis bitte bei Schritt 7: Anschließen des Kabeladapters fort. Befestigen Sie die Anschlussblöcke an der Vorderseite der Module. Welche Anschlussblöcke für welche Module geeignet sind, erfahren Sie unter .
  • Page 83 Verbinden Sie die 50-polige Federleiste auf der Rückseite des Kabel- adapters mit der Steckerleiste auf der Rückseite des entsprechenden SCXI-Moduls. Vorsicht! Den Adapter nicht gewaltsam anbringen. Die Kontakte können sonst beschädigt werden. Schrauben Sie den Adapter an der Rückseite des Chassis fest. © National Instruments Corporation SCXI-Schnellstartanleitung...
  • Page 84: Multichassis-System

    1 SCXI-Chassis 3 Stecker 2 Kabeladapter des Typs SCXI-1349 4 Schrauben Abbildung 9. Montage des Kabeladapters Multichassis-System Hinweis Adapter des Typs SCXI-1346 sind so breit wie zwei Module. Aus diesem Grund kann an ein Modul rechts neben dem Adapter kein Kabel angeschlossen werden. Für einen Messaufbau mit mehreren Chassis ist für jedes Chassis ein sol- cher Adapter erforderlich, mit Ausnahme des Chassis, das am weitesten von der DAQ-Karte der E-Serie entfernt ist.
  • Page 85: Schritt 8: Anschließen Der Module An Die Daq-Karte

    1 Chassis des Typs SCXI-1000 oder SCXI-1001 2 Kabeladapter des Typs SCXI-1346 3 Abgeschirmtes Kabel, das mit TO NEXT CHASSIS verbunden ist 4 Kabel, das mit FROM DAQ BOARD OR PREVIOUS CHASSIS verbunden ist Abbildung 10. Kabeladapter des Typs SCXI-1346 Bringen Sie an das letzte Chassis den Adapter des Typs SCXI-1349 an.
  • Page 86: Multichassis-System

    Multichassis-System Verbinden Sie ein Ende des 68-poligen Kabels mit der DAQ-Karte der E-Serie. Schließen Sie das andere Kabelende an den SCXI-1346-Adapter im Chassis n mit der Beschriftung FROM DAQ BOARD OR PREVIOUS CHASSIS an. Verbinden Sie das 68-polige Kabel mit dem SCXI-1346-Adapter in Chassis n mit der Beschriftung TO NEXT CHASSIS.
  • Page 87: Schritt 9: Einschalten Des Chassis

    Bei Systemen im Netzwerk, die mit LabVIEW Real-Time arbeiten, klicken Sie zunächst die Kategorie Netzwerkumgebung, dann das System und anschließend die Kategorie Geräte und Schnitt- stellen doppelt an. Überprüfen Sie, ob das Gerät unter “Geräte und Schnittstellen” ange- zeigt wird. © National Instruments Corporation SCXI-Schnellstartanleitung...
  • Page 88: Schritt 12: Hinzufügen Weiterer Chassis

    1 Wenn ein Gerät sowohl mit dem (alten) traditionellen NI-DAQ-Treiber als auch mit NI-DAQmx arbeitet, und beide Treiber installiert sind, wird es unter Mein System»Geräte und Schnittstellen mit unterschiedlichen Namen in beiden Kategorien aufgeführt. 2 Beachten Sie bitte, dass unter Netzwerkumgebung»Geräte und Schnittstellen nur die NI-DAQmx-Geräte angezeigt werden.
  • Page 89: Hinzufügen Von Scxi-Chassis Unter Ni-Daqmx

    Wählen Sie unter NI-DAQmx-Geräte»NI-DAQmx - SCXI-Chassis das verwendete Gehäuse aus. Klicken Sie auf Beenden. Statt dessen können Sie auch mit der rechten Maustaste auf Geräte und Schnittstellen»NI-DAQmx-Geräte klicken und die Option Neu» NI-DAQmx - SCXI-Chassis auswählen. © National Instruments Corporation SCXI-Schnellstartanleitung...
  • Page 90: Hinzufügen Von Scxi-Chassis Beim Alten Traditionellen Ni-Daq-Treiber

    Hinzufügen von SCXI-Chassis beim alten traditionellen NI-DAQ-Treiber Zum Hinzufügen eines mit dem traditionellen NI-DAQ-Treiber gesteuer- ten SCXI-Gehäuses zum lokalen System gehen Sie wie folgt vor: Klicken Sie mit der rechten Maustaste auf Geräte und Schnittstellen und wählen Sie Neu. Klicken Sie mit der rechten Maustaste auf Geräte und Schnittstellen»Traditionelle NI-DAQ-Geräte und wählen Sie SCXI-Chassis hinzufügen.
  • Page 91 Zustand versetzt werden. Trennen Sie daher die Verbindung zu allen Geräten, bei denen die die automatische Modulerkennung Probleme verursachen könnte. Klicken Sie auf Speichern. Es öffnet sich das Dialogfeld zur Konfigu- ration von SCXI-Chassis. Die Registerkarte Module ist bereits per Voreinstellung ausgewählt. © National Instruments Corporation SCXI-Schnellstartanleitung...
  • Page 92 Wenn die automatische Modulerkennung nicht aktiviert wurde, wählen Sie im Feld Modul ein SCXI-Modul aus. Vergewissern Sie sich, dass sich das Modul im angegebenen Steckplatz befindet. Um den Namen des SCXI-Moduls zu ändern, klicken Sie in das Feld Gerätekennung. Der Name muss alphanumerisch sein und darf nur einmal vergeben werden.
  • Page 93 13. Bei Verwendung eines Moduls zur Erfassung analoger Signale im Pa- rallelmodus, bei einer Schaltung mit mehreren Chassis oder einem anderen Spezialfall sind die Optionen auf der Registerkarte Verkabe- lung entsprechend anzupassen. Für den Standard-Multiplexmodus können die Einstellungen beibehalten werden. © National Instruments Corporation SCXI-Schnellstartanleitung...
  • Page 94 14. Unter Mit dem Modul verbundene Karte ist die DAQ-Karte auszu- wählen, die mit dem SCXI-Modul verbunden ist. 15. Wählen Sie unter Modul-Digitalisierer eine DAQ-Karte aus. • Im Multiplexmodus ist auch ein anderes Modul als A/D-Umsetzer zulässig. Für den Multiplexmodus muss die Digitalisierungsop- tion Gemultiplext aktiviert werden.
  • Page 95: Hinzufügen Von Modulen Zu Einem System Bei Nutzung Von Ni-Daqmx

    Klicken Sie auf das Chassis. Sie sehen nun eine Liste aller Steckplätze des Chassis. Klicken Sie mit der rechten Maustaste auf einen freien Steckplatz und wählen Sie Einfügen. Es öffnet sich das Dialogfeld zur Konfiguration von SCXI-Chassis. © National Instruments Corporation SCXI-Schnellstartanleitung...
  • Page 96: Konfiguration Von Chassis Und Modulen Beim Alten Traditionellen Ni-Daq-Treiber

    Klicken Sie auf Auto-Erkennung aller Module und anschließend auf Ja. Gehen Sie zur Konfiguration des Moduls nach den Anweisungen ab Schritt 6 des vorangegangenen Abschnitts nach. Testen Sie das Chassis, wie in Schritt 14: Überprüfen des Chassis beschrieben. Konfiguration von Chassis und Modulen beim alten traditionellen NI-DAQ-Treiber Bei Verwendung des traditionellen NI-DAQ-Treibers sind zur Konfigura- tion eines lokalen SCXI-Chassis folgende Schritte erforderlich:...
  • Page 97 Erweitern Sie die Kategorie Geräte und Schnittstellen»Traditio nelle NI-DAQ-Geräte. Klicken Sie auf das Chassis. Sie sehen nun eine Liste aller darin befindlichen Module. Klicken Sie mit der rechten Maustaste auf einen Modulsteckplatz und wählen Sie Eigenschaften. © National Instruments Corporation SCXI-Schnellstartanleitung...
  • Page 98 Es öffnet sich das Fenster zur Modulkonfiguration. Die Registerkarte Allgemein ist automatisch ausgewählt. Wählen Sie unter Verbunden mit die DAQ-Karte aus, an die das Modul angeschlossen ist. Wenn das Chassis mit dieser Karte gesteuert wird, markieren Sie das entsprechende Kästchen. Wählen Sie einen Betriebsmodus aus (Parallel- oder Multiplex- modus).
  • Page 99: Hinzufügen Von Modulen Zu Einem Lokalen System Bei Nutzung Des Alten Traditionellen Daq-Treibers

    Klicken Sie mit der rechten Maustaste auf einen freien Steckplatz und wählen Sie Einfügen. Wählen Sie das Modul, das Sie zu Ihrem Chassis hinzufügen möchten. Klicken Sie auf Weiter. Die Grundeinstellung für Verbunden mit lautet kein. © National Instruments Corporation SCXI-Schnellstartanleitung...
  • Page 100: Schritt 14: Überprüfen Des Chassis

    Wählen Sie einen Betriebsmodus aus (Parallel- oder Multiplexmo- dus). Klicken Sie auf Weiter. Wenn Sie mit einem Modul mit softwarekonfigurierbarem Filter und/oder Verstärker für jeden Kanal arbeiten, nehmen Sie die gewünschten Einstellungen vor. Klicken Sie auf Weiter. Die softwarekonfigurierbaren Eigenschaften von Modulen werden auch in der Hilfe zum Measurement &...
  • Page 101: Schritt 15: Konfiguration Der Kanäle Und Tasks

    Schritt 15: Konfiguration der Kanäle und Tasks Dieser Schritt ist nur dann erforderlich, wenn Sie Ihre Karte mit NI-DAQ oder einer Entwicklungsumgebung von National Instruments programmie- ren. Lesen Sie zu diesem Thema bitte auch den Abschnitt Konfiguration der Kanäle und Tasks in der DAQ-Schnellstartanleitung.
  • Page 102: Fehlersuche

    Fehlersuche Nachfolgend soll auf einige Fragen zu SCXI eingegangen werden, die unserer Support-Abteilung häufig gestellt werden. Daneben finden Sie ein paar Tipps, die Ihnen im Problemfall weiterhelfen sollen. Tipps Bevor Sie sich mit uns wegen eines Problems in Verbindung setzen, pro- bieren Sie folgende Tipps aus: •...
  • Page 103: Informationsquellen

    Modul und am Chassis leuchten. Wenn eine der LEDs nicht leuchtet, ist mindestens eine Sicherung durchgebrannt. Beim SCXI-1000 sind die Sicherungen nur nach Entfernen des Lüfters zugänglich. Beim SCXI-1001 befinden sie sich auf der Rückseite hinter dem rechten Lüfter in der Nähe des Stromversorgungsmoduls.
  • Page 104 Biegen Sie die Drähte der neuen Sicherung so um, dass sie in den Sockel passt (dieser ist ca. 13 mm lang) und kürzen Sie die abgeboge- nen Enden auf eine Länge von ca. 6 mm. Setzen Sie die Sicherung mit der Spitzzange vorsichtig in den Sicherungssockel.
  • Page 105 Die meisten Thermoelemente sind erdfreie Signalquellen mit einer geringen Gleichtaktspannung. Sie müssen so geschaltet werden, dass der Ruhestrom vom Verstärker des SCXI-Moduls an einen Masseanschluss abgeleitet wird. Vergewissern Sie sich, ob die negative Leitung jedes Ther- © National Instruments Corporation SCXI-Schnellstartanleitung...
  • Page 106: Weltweite Technische Unterstützung

    Sie sich bei Problemen ni.com/exchange mit Hunderten Applikationsingenieuren weltweit austauschen können. Die Applikationsingenieure von National Instruments sorgen dafür, dass alle Ihre Fragen beantwortet werden. Welche Art der technischen Unterstützung in Ihrer Nähe verfüg- bar ist, erfahren Sie unter oder bei einer ni.com/services...
  • Page 107: Technische Daten

    Sie unter das zuge- ni.com/calibration hörige Kalibrierungszertifikat. Die Adresse der Hauptgeschäftsstelle von National Instruments lautet 11500 North Mopac Expressway, Austin TX, 78759-3504, USA. Auf die Websites unserer einzelnen Niederlassungen mit Kontaktangaben, Tele- fonnummern des technischen Supports, E-Mail-Adressen sowie Hinweisen auf aktuelle Ereignisse und Veranstaltungen gelangen Sie über...
  • Page 108: Ce-Zulassung

    CE-Zulassung Die von Ihnen erworbenen Produkte erfüllen die Mindestanforderungen der geänderten europäischen Richtlinien für das CE-Prüfsiegel: Niederspannungsrichtlinie (Sicherheit) ..........73/23/EEC Elektromagnetische Verträglichkeit Richtlinie (EMV) ........89/336/EEC Welche behördlichen Sicherheitsstandards das Produkt außerdem erfüllt, ist in Hinweis der dazugehörigen Konformitätserklärung beschrieben. Zur Suche nach Konformitätser- klärungen besuchen Sie , geben die Nummer des betreffenden ni.com/certification...
  • Page 109 National Instruments Corporation 、 、 、および は (米国ナショナルインスツルメンツ社)の商標です。 National Instruments Term of Use の商標の詳細については、 ni.com/legal の「 」セクションを参照してください。本文書中に記載されたその他の製品名および National Instruments 企業名は、それぞれの企業の商標または商号です。 の製品を保護する特許については、ソフトウェアに含まれている特許情報(ヘルプ→特許 情報) 、 に含まれている patents.txt ファイル、または ni.com/patents のうち、該当するリソースから参照してください。 373236E © 2003–2005 National Instruments Corp. All rights reserved. 2005 年 月版...
  • Page 110 9. SCXI ............124 手順 シャーシに電源を投入する 10. Measurement & Automation Explorer 手順 ( ) ........................124 を起動する ....124 手順 シャーシとモジュールが認識されたことを確認する ................125 手順 シャーシを追加する ................126 コントローラを認識する NI-DAQmx SCXI ..........126 に シャーシを追加する NI-DAQ SCXI ....127 従来型 (レガシー)に シャーシを追加する ............127 手順 シャーシとモジュールを設定する NI-DAQmx ........127 でシャーシとモジュールを構成する NI-DAQmx .....131 で既存のシステムにモジュールを追加する...
  • Page 111 ご使用のモジュールおよびコンポーネントは、静電気による損傷( 、 静電破壊)を防ぐため、静電防止の梱包で出荷されています。 注意 露出しているコネクタピンには絶対に触れないでください。 このような損傷を回避するには、以下の予防措置を講じてください。 • 接地ストラップを使用したり、接地された物体に触れたりして、身体 を接地する。 • 静電防止の梱包をシャーシの金属部分に接触させてから、モジュール を梱包箱から取り出す。 シャーシ、モジュール、およびアクセサリを箱から取り出し、部品がゆる んでいないかどうか、また、損傷箇所がないかどうかを調べます。製品が 損傷している場合は、ナショナルインスツルメンツまでご連絡ください。 損傷したデバイスをインストールしないでください。 モジュールを使用しないときは、静電防止の梱包に保管してください。 安全およびコンプライアンスの情報については、デバイスに梱包されてい NI-DAQ た、もしくは ソフトウェアキットもしくは ni.com/jp/ NI-DAQ 7.x Device Documentation CD から取得できる 付属 support Device Document Browser のデバイス関連文書を参照してください。 © National Instruments Corporation SCXI クイックスタートガイド...
  • Page 112 National をインストール後、デバイスの文書はスタート→プログラム→ Instruments NI-DAQ Browse Device Documentation → → から表示 できます。 手順 コンポーネントを確認する SCXI 図 に示される システムコンポーネントが梱包されているかどうか を確認します。 ® W ER SCXI ターミナルブロックまたは アクセサリ(オプション) シャーシのみ モジュール シャーシアダプタアセンブリ SCXI モジュール デバイス PXI/SCXI 10 USB コンボシャーシおよびコントローラ ケーブル SCXI 11 SCXI USB シャーシ デバイス...
  • Page 113 使用しているシャーシがアドレス可能な場合、シャーシアドレスを設 定します。旧タイプのシャーシにはアドレス可能でないものもあり ます。 • シャーシにアドレススイッチがある場合、オフに設定します。 図 では、スイッチはすべて の位置にあります。 • 旧タイプのシャーシには、正面パネルの内側にジャンパを使用 し、シャーシアドレススイッチを使用しないものがあります。 ヒューズと 電源の選択に関しても異なります。詳細につい ては、それぞれのシャーシ関連文書を参照してください。 100/120/220/240 VAC 適切な電源設定( )を確認します。 電源コードを接続します。 ® 1 2 0 RESET 正面 シャーシの電源スイッチ 電圧選択タンブラ 背面 シャーシのアドレススイッチ 電源コードのコネクタ 2 SCXI 図 シャーシのセットアップ © National Instruments Corporation SCXI クイックスタートガイド...
  • Page 114 PXI/SCXI コンボシャーシ メモ システムコントローラは、シャーシの 側にインストールされる必要がありま PXI/SCXI す。インストールサービスを通じて構成された コンボシャーシを注文 する方法の詳細については、 を開いて を入力します。 ni.com/jp/info rdfisj SCXI および の電源を切り、シャーシのコードを抜いてください。 2. SCXI アドレススイッチを にしてください。図 では、スイッチ はすべて の位置にあります。 電圧選択タンブラを使用しているアプリケーションに適切な電圧に設 定します。詳細については、それぞれのシャーシ関連文書を参照して ください。 電源コードを接続します。 1 2 0 RESET 正面 電源コードのコネクタ 電源スイッチ 背面 アドレススイッチ システムコントローラ SCXI 電圧選択タンブラ 電源スイッチ 3 PXI/SCXI 図...
  • Page 115 モジュール はホットスワップには対応していません。電源が のときにモジュールを追 加したり、取り外したりすると、シャーシのヒューズが飛んだり、シャーシや モジュールを損傷する場合があります。 PXI/SCXI コンボシャーシ PXI E シャーシの最も右のスロットに シリーズまたは シリーズの の通信デバイスをインストールするには、以下の手順に従ってくだ さい。 静電気を放電するため、シャーシの金属部分に触れます。 図 のように、モジュールの縁を上下の モジュールガイドに配 置します。 シャーシの後部にモジュールを差し込みます。脱着ハンドルが押し下 げられていることを確認します。 抵抗を感じたら、脱着ハンドルを引き上げて、モジュールを枠に挿入 します。 モジュールをシャーシのフロントパネル取り付けレールに、 つのネ ジを使用して取り付けます。 PXI DAQ モジュール 脱着レール 脱着ハンドル 図 新規シャーシに モジュールを取り付ける © National Instruments Corporation SCXI クイックスタートガイド...
  • Page 116 SCXI シャーシ 静電気を放電するため、シャーシの金属部分に触れます。 2. SCXI スロットにモジュールを挿入します。 モジュールをシャーシのフロントパネル取り付けレールに、 つのつ まみネジを使用して取り付けます。 ® つまみネジ モジュール SCXI 図 新規シャーシに モジュールを取り付ける SCXI USB モジュール SCXI-1600 SCXI USB PXI/SCXI メモ などの モジュールは、 コンボシャーシまたはマ ルチシャーシシステムで使用することができません。 SCXI USB SCXI モジュールは、プラグアンドプレイ対応の、 システムと 対応コンピュータまたは ハブ間を通信する信号調節実装モ ジュールであるため、中間 デバイスは必要ありません。モジュール をシャーシに取り付けた後、以下の手順に従ってください。 SCXI USB ケーブルを、...
  • Page 117 図 モジュールを取り付ける SCXI 既存の システムにモジュールを追加する SCXI マルチプレスクモードで既存の システムにモジュールを追加するこ ともできます。お使いのシステムに既にコントローラが設定されている場 SCXI 合、追加 モジュールを空いているシャーシスロットに前述の方法で 取り付けることができます。ケーブルアダプタに接続するモジュールを決 定するには(該当する場合) 、 「手順 ケーブルアタプタを取り付ける」 SCXI の モジュールの一覧を参照してください。 SCXI SCXI 新規 モジュール シャーシ SCXI 既存 モジュール 既存 デバイス SCXI 図 既存システムに モジュールを取り付ける © National Instruments Corporation SCXI クイックスタートガイド...
  • Page 118 – (英語)を参照してください。 ni.com/sensors – LabVIEW LabVIEW を使用する場合は、 に同梱されている LabVIEW Measurements Manual 『 』または ni.com/jp/ を参照してください。 manuals – NI-DAQmx を使用する場合には、スタート→プログラム→ National Instruments NI-DAQ NI-DAQmx Help → → から表 NI-DAQmx Help Sensors 示できる『 』の「 」のトピックを参照 してください。 – NI-DAQ 従来型 (レガシー)を使用する場合には、スタート→プ National Instruments...
  • Page 119 SCXI ターミナルブロックの モジュールへの取り付け SCXI モジュールの正面パネル 図 ターミナルブロックを取り付ける 手順 ケーブルアタプタを取り付ける シングルシャーシシステム SCXI-1600 SCXI USB メモ などの モジュールを既にインストールした場合、もしくは PXI/SCXI 9. SCXI コンボシャーシを使用する場合は「手順 シャーシに電源を投 入する」へ進みます。 SCXI 適切な モジュールを認識して、ケーブルアダプタに接続します : SCXI-1349 (例 ) 。同時サンプリング機能を持つアナログ入力モ ジュールを、シャーシにあるようにケーブルアセンブリに接続する必 要があります。同時サンプリング機能を持たないモジュールを接続し た場合、アプリケーションを実行するたびにエラーメッセージが表示 されます。 © National Instruments Corporation SCXI クイックスタートガイド...
  • Page 120 • すべてのモジュールがマルチプクレスモードの場合、以下のリス トのどのモジュールが最初に発生するか決定し、ケーブルアダプ タを取り付けます。 SCXI-1520 SCXI-1530 SCXI-1531 SCXI-1540 SCXI-1140 、 、 、 、 SCXI-1521/B SCXI-1112 SCXI-1102/B/C SCXI-1104/C SCXI-1125 、 、 、 、 、 SCXI-1126 SCXI-1141 SCXI-1142 SCXI-1143 SCXI-1581 、 、 、 、 SCXI-1120/D SCXI-1121 SCXI-1100 SCXI-1122 、 、 、 SCXI-1124 SCXI-116x 、...
  • Page 121 シリーズ デバイスから SCXI-1346 一番遠いシャーシを除いて、チェーン内の各シャーシにつき マルチシャーシアダプタを つ使用する必要があります。最後のシャー SCXI-1349 シが ケーブルアダプタを使用します。 SCXI 適切な モジュールを識別して、ケーブルアダプタに接続しま す。適切なモジュールを特定するには、 「シングルシャーシシステム」 セクションの手順 を参照してください。 ケーブルアダプタの後部にある ピンメスコネクタを、適切な SCXI モジュールの後部にある ピンオスコネクタに挿入します。 3. SCXI-1346 SCXI 付属のネジで、アダプタを シャーシの後部に固定し ます。 SCXI SCXI チェーン内の最後の シャーシを除いて、システム内の各 シャーシに対して手順 から を繰り返し行います。 © National Instruments Corporation SCXI クイックスタートガイド...
  • Page 122 SCXI-1000 SCXI-1001 または シャーシ SCXI-1346 ケーブルアダプタ TO NEXT CHASSIS に接続しているシールドケーブル FROM DAQ BOARD OR PREVIOUS CHASSIS に接続しているシールドケーブル 10 SCXI-1346 図 ケーブルアセンブリ 5. SCXI-1349 SCXI ケーブルアダプタをチェーン内の最後の シャーシに SCXI-1349 取り付けます。 を取り付ける方法の詳細については、 「シ ングルシャーシシステム」セクションの手順 を参照してください。 手順 モジュールを デバイスに接続する シングルシャーシシステム PXI/SCXI コンボシャーシにモジュールを取り付けた場合、シャーシの バックプレーンがモジュールと デバイスを接続しています。...
  • Page 123 最後のシャーシに到達するまで、手順 と手順 を残りのシャーシ に対して繰り返します。 TO NEXT CHASSIS 最後から 番目のシャーシにある、 「 」というラベ ルの付いたコネクタに ピンシールドケーブルを接続します。 SCXI-1349 最後のシャーシにある にケーブルの反対側を接続します。 – – – SCXI-1349 ケーブルアダプタに接続されたシールドケーブル ターミナルブロック SCXI-1346 ケーブルアダプタに接続されたシールドケーブル センサ SCXI デバイス シャーシ シールドケーブルから デバイス SCXI 図 完成した システム © National Instruments Corporation SCXI クイックスタートガイド...
  • Page 124: Scxi シャーシに電源を投入する

    9. SCXI 手順 シャーシに電源を投入する SCXI シャーシを使用する場合、シャーシの電源スイッチは「手順 PXI/SCXI シャーシをセットアップする」の図 に示されています。 コン ボシャーシを使用する場合、 とシャーシの電源スイッチは「手順 シャーシをセットアップする」の図 に示されています。 Windows は、ハードウェアのインストール後に初めてコンピュータが再 起動されたときに、新しくインストールされたデバイスを認識します。一 Windows 部の システムでは、インストールされたすべての デバイス に対して、新しいハードウェアの検索ウィザードが起動します。デフォル トにより、デバイスに最適なドライバを検索する(推奨)が選択されま Windows す。 がデバイスを認識するように、次へまたははいをクリック して各デバイスのソフトウェアをインストールします。 SCXI-1600 コントローラが モジュールなどの デバイスを認識する と、モジュールのフロントパネルの が点滅または点灯します。 の点滅パターンおよびトラブルシューティングについては、デバイスの関 連文書を参照してください。 10. Measurement & Automation Explorer 手順...
  • Page 125: 手順 12. シャーシを追加する

    <F5> デバイスが表示されない場合には、 を押して の表示を更 新します。デバイスがまだ認識されないときは、 ni.com/support/ のトラブルシューティングを参照してください。シャー ja/trouble シが認識されない場合には、この文書の「トラブルシューティング」 セクションを参照してください。 手順 シャーシを追加する NI-DAQmx ハードウェアをインストールすることなく、 によってシミュ SCXI NI-DAQmx レートされた シャーシおよびモジュールを使用して、 アプリケーションをテストすることができます。シミュレートしたデバイ スを作成、そしてシミュレートしたデバイスの構成を物理デバイスにイン NI-DAQmx ポートする手順については、ヘルプ→ヘルプトピック→ を選 NI-DAQmx Measurement & Automation Explorer 択して、 『 対応 ヘル プ』を参照してください。 © National Instruments Corporation SCXI クイックスタートガイド...
  • Page 126: Pxi コントローラを認識する

    コントローラを認識する PXI/SCXI NI-DAQmx コンボシャーシを使用している場合は、 または従来 NI-DAQ 型 (レガシー)で以下の手順を実行して、使用しているシャーシ にインストールされている埋め込み式 コントローラを識別します。 システムを右クリックして、次のモデルとして識別を選択しま す。リモート ターゲットを使用する場合、リモートシステムを展 開し、ターゲットを検索して展開して、 システムを右クリックし ます。 2. PXI コントローラをリストから選択します。 PXI-1052 NI-DAQ PXI-1011 メモ シャーシを従来型 と使用する場合、そのシャーシを シャーシとして識別してください。 NI-DAQmx SCXI に シャーシを追加する SCXI-1600 SCXI USB メモ などの モジュールをインストールした場合は、 「手順 SCXI USB シャーシとモジュールを設定する」へ進みます。 モジュールと関連...
  • Page 127: Ni-Daq Scxi

    択します。 終了をクリックします。 手順 シャーシとモジュールを設定する NI-DAQ API 構成の手順は、シャーシおよびモジュールの制御に使用する NI-DAQmx NI-DAQ ( または従来型 (レガシー) )によって異なります。 NI-DAQmx でシャーシとモジュールを構成する SCXI-1600 メモ でシャーシを構成する場合は、シャーシを右クリックして、プロパ SCXI-1600 ティを選択し、このセクションの手順 へ進んでください。 は、他 のすべてのモジュールを自動検出します。 図を見ながら以下の手順に従ってください。 SCXI シャーシ通信デバイスから、 通信モジュールにケーブルで接続 した デバイスを選択します。 が デバイスを つだ け検出している場合は、デフォルトによりそのデバイスが選択され、 このメニューは操作不可となります。 © National Instruments Corporation SCXI クイックスタートガイド...
  • Page 128 SCXI 通信する モジュールスロットから、シャーシ通信デバイスに接 続されているモジュールスロットを選択します。 シャーシアドレスにシャーシアドレスの設定を入力します。設定が SCXI シャーシのアドレス設定と一致することを確認してください。 4. SCXI モジュールを自動検出するかどうかを選択します。モジュール SCXI を自動検出しない場合は、 は通信する モジュールスロッ トを無効にします。 注意 自動検出機能は ラインをトグルするため、接続されているデバイスが不明 な状態や適切でない状態におかれることがあります。自動検出によって問題が 発生する可能性のあるデバイスをすべて、システムから外してください。 SCXI 保存をクリックします。 シャーシ構成ウィンドウが開きます。 デフォルトにより、モジュールタブが選択されます。 モジュールを自動検出しなかった場合は、モジュール配列リストボッ SCXI クスから モジュールを選択します。モジュールを正しいスロッ トに指定したことを確認してください。 SCXI モジュール名を変更するには、デバイス識別子フィールドをク リックして固有の を英数字で入力します。 はデバイス識別 子にデフォルト名を表示します。 接続されたアクセサリを使用している場合、アクセサリで指定します。 SCXI ni.com/jp クイックスタートガイド...
  • Page 129 詳細をクリックします。詳細ウィンドウが開きます。 SCXI ジャンパで選択した設定で モジュールを構成する場合は、ジャ ンパタブをクリックしてハードウェアで選択した設定を入力します。 アクセサリタブをクリックします。アクセサリドロップダウンリスト ボックスから互換性のあるアクセサリを選択します。 構成をクリックして設定を承諾します。すべてのアクセサリに設定が あるとは限りません。詳細については、アクセサリの関連文書を参照 してください。 アナログ入力モジュールをパラレルモード、マルチシャーシ構成、ま たは別の特別な構成で使用している場合には、ケーブルタブをクリッ クしてケーブルの設定を調整します。標準マルチプレクスモード操作 を使用している場合には、設定を変更する必要はありません。 © National Instruments Corporation SCXI クイックスタートガイド...
  • Page 130 SCXI どのデバイスをこのモジュールに接続しますか リストから、 モジュールに接続した デバイスを選択します。 モジュールデジタイザリストから デバイスを選択します。 • マルチプレクスモードでは、異なるモジュールをモジュールデジ タイザにすることができます。モジュールをマルチプレクスモー ドで操作している場合は、マルチプレクスデジタイザモードを選 択していることを確認してください。 • パラレルモードでは、モジュールに接続されたデバイスとモ ジュールデジタイザは同一です。モジュールをパラレルモードで 操作している場合は、パラレルデジタイザモードを選択している ことを確認してください。 デジタイザモードを選択します。 • マルチプレクスモードについては、マルチシャーシデイジー チェーン指標ドロップダウンリストボックスから指標番号を選択 します。 • パラレルモードについては、デジタイザチャンネルドロップダウ ンリストボックスからチャンネルの範囲を選択します。ケーブル 接続のデバイスが1つのコネクタのみを持つ場合、チャンネルの 範囲は自動的に選択されます。 メモ 一部の シリーズデバイスは つのコネクタを特長としています。モジュール にケーブル接続しているコネクタに対応するチャンネルの範囲を選択する必要 があります。チャンネル ~ はコネクタ に対応しています。チャンネル ~ はコネクタ に対応しています。 注意 シャーシをデイジーチェーン接続から取り外した場合、別のシャーシのモ...
  • Page 131: Ni-Daqmx で既存のシステムにモジュールを追加する

    ら構成を保存することを推奨します。 21. IEEE 1451.4 TEDS トランスデューサ電子データシート( )センサおよ びアクセサリについては、上記の方法でデバイスを構成してアクセサ TEDS リを追加します。デバイスに直接接続された センサを構成する には、 のデバイスとインタフェースの下にあるモジュールを右 TEDS クリックして、 を構成を選択します。構成ウィンドウの TEDS をスキャンをクリックします。 NI-DAQmx で既存のシステムにモジュールを追加する 次の手順に従ってください。 NI-DAQmx デバイスとインタフェース→ デバイスを展開します。リ モート ターゲットを使用している場合、リモートシステムを選択 し、ターゲットを展開して、デバイスとインタフェース→ NI-DAQmx デバイスを右クリックします。 スロットのリストを表示するシャーシをクリックします。 SCXI 空のスロットを右クリックして、挿入を選択します。 シャーシ 構成ウィンドウが開きます。 © National Instruments Corporation SCXI クイックスタートガイド...
  • Page 132: 従来型 Ni-Daq (レガシー)でシャーシとモジュールを構成する

    全モジュール自動検出、そしてはいをクリックします。 前のセクションの手順 まで戻り、説明に従ってモジュールを構成 してください。 「手順 シャーシをテストする」で説明されているように、シャー シをテストします。 NI-DAQ 従来型 (レガシー)でシャーシとモジュールを構成する SCXI NI-DAQ ローカル シャーシを従来型 (レガシー)で構成するには、 SCXI 以下の手順に従って図のように シャーシを構成します。 SCXI 3200 シャーシの を選択します。 には ~ の任意の整数 を使用することができます。この を使用してアプリケーションの シャーシを識別してください。 シャーシのアドレス設定を入力します。シャーシのアドレスには、 SCXI ~ の任意の値を使用することができます。設定が シャーシ のアドレス設定と一致していることを確認してください。シャーシア ドレスのスイッチの位置については、 「手順 シャーシをセットアッ プする」を参照してください。次へをクリックします。 3. SCXI モジュールを自動検出するかどうかを選択します。次へをク...
  • Page 133 デバイスを選択します。このデバイスは、シャーシとコンピュー タの間の通信パスのように動作します。次へをクリックします。 SCXI ケーブルで通信デバイスに接続した モジュールを選択します。 NI-DAQ シャーシにモジュールが つしかない場合、デフォルトで はそのモジュールを選択します。 完了をクリックして設定を承諾します。 NI-DAQ 以下の手順に従って、従来型 (レガシー)を使用してモジュール をローカルシステムで構成します。 NI-DAQ デバイスとインタフェース→従来型 (レガシー)デバイスを 展開します。 モジュールのリストを表示するシャーシを展開します。 モジュールのスロットを右クリックしてプロパティを選びます。 © National Instruments Corporation SCXI クイックスタートガイド...
  • Page 134 SCXI モジュールをシャーシスロットに構成ウィンドウが開きます。 デフォルトにより、一般設定タブが選択されます。 モジュールに接続する デバイスを接続先リストから選択しま す。 デバイスがシャーシを制御する場合は、チェックボックス にチェックマークを付けます。 操作モードからモード(マルチプレクスまたはパラレル)を選択し ます。 ソフトウェア選択可能フィルタと各チャンネルのゲイン設定の両方ま たは片方が備えられているモジュールを使用している場合には、チャ ンネルタブをクリックして、設定を選択します。 アクセサリタブをクリックします。互換性のあるモジュールアクセサ リを選択します。 SCXI ni.com/jp クイックスタートガイド...
  • Page 135: モジュールを追加する

    をローカルシステムに追加します。 NI-DAQ デバイスとインタフェース→従来型 (レガシー)デバイスを 展開します。 スロットのリストを表示するシャーシを展開します。空のスロットを 右クリックして、挿入を選択します。 SCXI シャーシに追加する モジュールを選択します。次へをクリック します。 デフォルトでは接続先はなしが選択されます。 操作モードからモード(マルチプレクスまたはパラレル)を選択しま す。次へをクリックします。 ソフトウェア選択可能フィルタと各チャンネルのゲイン設定の両方ま たは片方が備えられているモジュールを使用している場合には、チャ ンネル値を設定します。表示されたフィールドから設定を選択しま す。次へをクリックします。 モジュールのソフトウェア構成可能なプロパティについては、 『従来 NI-DAQ Measurement & Automation Explorer 型 対応 ヘルプ』 を参照してください。 で、ヘルプ→ヘルプトピック→従来型 NI-DAQ (レガシー)を選択します。 アクセサリリストから対応するデバイスを選択します。 終了をクリックします。 © National Instruments Corporation SCXI クイックスタートガイド...
  • Page 136: 手順 14. シャーシをテストする

    手順 シャーシをテストする NI-DAQmx デバイスとインタフェース→ デバイス、またはデバイス NI-DAQ とインタフェース→従来型 (レガシー)デバイスを展開しま す。リモート ターゲット上のシャーシをテストすることは、従来 NI-DAQ 型 (レガシー)ではサポートされていません。 テストするには、シャーシ名を右クリックします。 テストを選択して、 がシャーシを認識することを確認します。 シャーシが認識されない場合、メッセージが表示されます。 各モジュールが正常にインストールされているかどうかをテストするに は、テストするモジュールを右クリックして、テストパネルをクリックし ます。エラーの詳細ボックスにエラーなしが表示された場合、モジュール は正常にインストールされています。 SCXI-1600 SCXI メモ をテストすると、 システム全体が確認されます。 SCXI システムは、正常に動作しています。 前の自己テストで、シャーシが正常に構成および動作していることを確認 SCXI できなかった場合、以下の手順で 構成の問題を解決します。 SCXI • SCXI シャーシの確認メッセージボックスが開いて、 シャーシ ID: x モデル番号シャーシ を表示し、...
  • Page 137: 手順 15. チャンネルの構成とタスクの設定

    トラブルシューティング SCXI このセクションは、トラブルシューティングのヒント、および ユー ザからのよくある質問の回答について記載しています。 ヒント にお問い合わせになる前に、以下のトラプルシューティングをお試し ください。 • SCXI シャーシの電源が であることを確認してください。 PXI/SCXI コンボシャーシを使用する場合、 とシャーシの電源ス イッチが になっていることを確認してください。 • NI-DAQ お使いのシステムのデバイスをサポートする ドライバソフト ウェアの最新バージョンをインストールしたことを確認してください。 • がシャーシとの通信を確立できない場合、以下のいずれかを試 してください。 – デバイスをシャーシ内の異なるモジュールに配線します。 – 他のケーブルアセンブリを試します。 – 他のシャーシを試します。 – 他の デバイスを試します。 © National Instruments Corporation SCXI クイックスタートガイド...
  • Page 138: リソース

    またはソフトウェアのインストールで問題が ある場合、以下のリソースを参照してください。 • トラブルシューティングの説明については、 ni.com/support/ja/ のトラブルシューティングリソースを参照 troubleshooting.htm してください。 • 一般的なインストールやプログラミングに関する問題点のトラブル FAQ) シューティングおよび の製品についてよくある質問( の回 答に関する文書については、 を参照してください。 ni.com/jp/kb • National Instruments デバイスが損傷した可能性があり、 ハード ウェアを修理またはキャリブレーションのために返却する必要がある 場合、日本ナショナルインスツルメンツ テクニカルサポートへお電 03-5472-2981 00-12 話ください。 電話番号:   (平日  : :   00-17 : : ) よくある質問 シャーシの電源は...
  • Page 139 を繰り返し ます。 ファンのラベルがある方を下にして、ファンとフィルタをファン穴に 合わせます。 つのネジを取り付けなおし、組み立てが固定している かどうかを確認します。 ヒューズの仕様については、シャーシユーザマニュアルを参照してくだ さい。 シャーシの電源を にしたままモジュールをうっかり外してしまいま した。そのままモジュールを元どおり取り付けましたが、シャーシがうま く動作しません。結局、シャーシに電源が入らなくなってしまいました。 どうしたらよいでしょうか SCXI モジュールはホットスワップに対応していないため、シャーシの ヒューズが飛んでしまった可能性があります。ヒューズを取り替えても問 SCXI 題が解消しない場合は、デジタルバス回路または モジュールが損傷 を受けた可能性があります。 から、ナショナルイン ni.com/support/ja スツルメンツの技術サポートまでお問い合わせください。 テスト中、 がシャーシを認識しません。どうしたらよいでしょうか 以下の項目を確認してください。 • シャーシに電源が入っていることを確認します。 • シャーシが デバイスに正しく接続されていることを確認しま す。複数の デバイスが に取り付けられている場合には、 © National Instruments Corporation SCXI クイックスタートガイド...
  • Page 140 シャーシ通信デバイスとして選択されたデバイスが実際にシャーシに 接続されていることを確認します。 • モジュールを取り付けた際に、バックプレーンのピンが曲がってし まったかどうかを確認します。 • モジュールの取り付け方および構成が正しいことを確認します。モ ジュールが自動検出されなかった場合、シャーシに取り付けられたモ ジュールはソフトウェアで構成されない可能性があります。また、ソ フトウェアで構成されたモジュールが、シャーシに取り付けたモ ジュールと一致していない可能性があります。 シャーシに電源が入っているかどうかをプログラムで検出できますか 構成済みのモジュールと通信できるかどうかを判断できます。 NI-DAQmx では、 にアクセスして とタイプす ni.com/express rdtscp LabVIEW VI NI-DAQ ると入手できる を使用します。従来型 (レガシー) では、 を使用してください。 SCXI_ModuleID_Read 計測しようとすると、すべてのチャンネルが正の方向に浮動します。どう やって問題を解決したらよいでしょうか? SCXI デバイスの信号基準設定が モジュールと一致していることを NRSE 確認します。たとえば、デバイスが に対して構成されている場合、 SCXI 接続されている モジュールも同じ構成であることを確認してくださ い。構成を一致させるには、モジュールのジャンパ設定を変更する必要が あります。...
  • Page 141: 世界各国の技術サポート

    NI Developer Exchange からアクセスできる で、世界各地から アプリケーションエンジニアへご質問を承ります。お尋ねいただ きましたご質問には、ナショナルインスツルメンツのアプリケー ションエンジニアが必ず解答いたします。 ご利用の地域のその他の技術サポートオプションについては、 をご覧頂くか、または ni.com/jp/services ni.com/jp/ から最寄の営業所までお問い合わせください。 contact • — トレーニングと認定 自習形式のコースキットやインストラクタによ る実践コースなどのトレーニングおよび認定プログラムについては、 にアクセスしてください。 ni.com/jp/training • — システムインテグレーション 時間の制約がある場合や社内で技術 リソースが不足している場合、または、その他のプロジェクトで簡単 には解消しない問題がある場合などは、ナショナルインスツルメンツ のアライアンスパートナーによるサービスをご利用いただけます。詳 しくは、最寄りの 営業所にお電話いただくか、 ni.com/jp/ をご覧ください。 alliance © National Instruments Corporation SCXI クイックスタートガイド...
  • Page 142: 安全性

    • — 適合宣言( ) 適合宣言とは、その会社の自己適合宣言を用い た、さまざまな欧州閣僚理事会指令への適合の宣言のことです。この EMC) 制度により、電磁適合性( に対するユーザ保護や製品の安全性 に関する情報が提供されます。ご使用の製品の適合宣言は、 (英語)から入手できます。 ni.com/certification • Calibration Certificate — ご使用の製品がキャリブレーションをサ ポートする場合、 からその製品の ni.com/calibration calibration certificate (英語)を入手してご利用になることもでき ます。 11500 North Mopac Expressway, ナショナルインスツルメンツ本社は Austin, Texas, 78759-3504 にあります。最新のコンタクト情報、サポー トの電話番号、電子メールアドレス、および現在のイベントの情報を提供 する海外オフィスのウェブサイトにアクセスするには、 (英語)を参照してください。 ni.com/niglobal 仕様 安全性 これらの製品は、計測、制御、実験に使用される電気装置に関する以下の 規格および安全性の必要条件を満たすように設計されています。...
  • Page 143: Ce 適合

    適合 これら製品は、以下のように (欧州委員会)マーク用に修正された該 当する欧州規格の主な要件を満たしています。 ........73/23/EEC 低電圧規格(安全性) 電磁環境両立性 ............ 89/336/EEC 規格( ) メモ この製品のこのほかの適合規格については、この製品の適合宣言( )を参 照してください。この製品の を取得するには、 ni.com/certification (英語)にアクセスしてモデル番号または製品ラインで検索し、保証の欄の該当 するリンクをクリックしてください。 © National Instruments Corporation SCXI クイックスタートガイド...

This manual is also suitable for:

Scxi-1001Scxi-1000dc

Table of Contents