Related Manuals for peerless-AV DS-LEDA27-10X10
Summary of Contents for peerless-AV DS-LEDA27-10X10
- Page 1 DS-LEDA27 Series For Absen Acclaim *Actual configuration may vary 2018-05-15 #:146-9026-4 (2019-08-15)
- Page 2 WARNING ENG - This product is designed to be installed on plywood walls. Hardware is included for plywood installation. Before installing make sure the supporting surface will support the combined load of the equipment and hardware. Screws must be tightly secured. Do not overtighten screws or damage can occur and product may fail. Never exceed the Maximum Load Capacity.
- Page 3 Parts (Before beginning, make sure you have all parts shown below). Parts List left column right column inside vertical top vertical bottom vertical Description column kit spacer spacer outside vertical column kit A1 left column A2 right column spacer kit B1 top vertical spacer B2 bottom vertical spacer (not used) B3 horizontal spacer...
- Page 4 Refer to layout drawing included for your specific model. 2018-05-15 #:146-9026-4 (2019-08-15)
- Page 5 Optional: If connecting two top horizontal extrusions, first remove inner hook-on brackets. Remove and save hardware. Use extrusion connectors to connect top horizontal extrusions. H (8) F (4) G (4) 2018-05-15 #:146-9026-4 (2019-08-15)
- Page 6 Replace one hook-on bracket in between connected extrusions. Use saved hardware. Optional: If connecting two bottom horizontal extrusions, first remove inner hook-on brackets Remove and save hardware. 2018-05-15 #:146-9026-4 (2019-08-15)
- Page 7 Use extrusion connectors to connect bottom horizontal extrusions. F (3) H (6) Replace one hook-on bracket in between connected extrusions. Use saved hardware. 2018-05-15 #:146-9026-4 (2019-08-15)
- Page 8 WARNING ENG - When installing Peerless wall mounts on a wood stud wall covered with plywood, verify that the wood studs are a minimum of 2" x 4" nominal size and plywood is a minimum Grade BC, 1/2" (13 mm) thick. Plywood may be covered by gypsum board (drywall) up to 5/8"...
- Page 9 Level top horizontal extrusion and mark mounting holes on plywood (must be minimum Grade BC, 1/2" (13mm) thick.) 3.94" (100mm) display tile 2018-05-15 #:146-9026-4 (2019-08-15)
- Page 10 2.5" (64mm) 5/32" 5/32" (4mm) (4mm) Drill mounting holes into supporting surface (2.5" (64mm) minimum depth required). Level extrusion. Install using wood screws provided. 3/8" (10mm) I (7) Maximum 80 in. • lb (9 N.M.). 2018-05-15 #:146-9026-4 (2019-08-15)
- Page 11 Edges must be flush. Secure vertical spacers to the wall flush with the horizontal extrusion. 3/8" (10mm) B1 (2) 2018-05-15 #:146-9026-4 (2019-08-15)
- Page 12 Use third vertical spacer to align bottom horizontal extrusion flush with vertical spacer, then mark mounting holes on plywood (must be minimum Grade BC, 1/2" (13mm) thick.) 56.19" (143cm) Edges must be flush. 2018-05-15 #:146-9026-4 (2019-08-15)
- Page 13 2.5" (64mm) 5/32" 5/32" (4mm) (4mm) Drill mounting holes into supporting surface (2.5" (64mm) minimum depth required). Use third vertical spacer to align bottom horizontal extrusion flush with vertical spacer, then install using wood screws 3/8" provided. (10mm) I (7) Maximum 80 in.
- Page 14 Remove vertical spacer. 3/8" (10mm) B1 (2) 2018-05-15 #:146-9026-4 (2019-08-15)
- Page 15 Hook on and secure outer vertical columns. "L" and "R" markings designate left and right Tighten hardware. column. J (8) 2018-05-15 #:146-9026-4 (2019-08-15)
- Page 16 Hook on and secure all inside vertical columns. Tighten hardware. J (16) C (4) 2018-05-15 #:146-9026-4 (2019-08-15)
- Page 17 Loosen hardware on vertical columns. 2018-05-15 #:146-9026-4 (2019-08-15)
- Page 18 Plumb and level outer columns, then tighten hardware. Tighten hardware on four corner wall plates. Tighten. Tighten. 2018-05-15 #:146-9026-4 (2019-08-15)
- Page 19 Tie a string between top slots on outer columns in order to level the depth of each vertical column. Loosen, adjust, tighten. Optional leveling for bowed walls Loosen. Insert. Tighten. 2018-05-15 #:146-9026-4 (2019-08-15)
- Page 20 Tie a string between bottom slots on outer columns in order to level the depth of each vertical column. Loosen, adjust, tighten. Optional leveling for bowed walls Loosen. Insert. Tighten. 2018-05-15 #:146-9026-4 (2019-08-15)
- Page 21 Tighten or loosen to adjust height. With the string still attached, level the height of each column 2018-05-15 #:146-9026-4 (2019-08-15)
- Page 22 Adjust inner columns to fit horizontal spacers. Tighen column hardware after spacing. Start from the left column. 2018-05-15 #:146-9026-4 (2019-08-15)
- Page 23 Continue adjusting inner columns to fit horizontal spacers until all are level. Tighen column hardware after spacing 2018-05-15 #:146-9026-4 (2019-08-15)
- Page 24 Remove all spacers. 2018-05-15 #:146-9026-4 (2019-08-15)
- Page 25 Optional: For shallow depth installations, flip wall bracket orientation as shown. 2.60" 2.25" (66mm) (57mm) 3.05" 2.65" (77mm) (67mm) 2018-05-15 #:146-9026-4 (2019-08-15)
- Page 26 Level L brackets and mark mounting holes on plywood (must be minimum Grade BC, 1/2" (13mm) thick.) 2018-05-15 #:146-9026-4 (2019-08-15)
- Page 27 2.5" (64mm) 5/32" 5/32" (4mm) (4mm) Drill mounting holes into supporting surface (2.5" (64mm) minimum depth required). Level L brackets. Install using wood screws provided. 3/8" (10mm) Maximum 80 in. • lb (9 N.M.). I (10) 2018-05-15 #:146-9026-4 (2019-08-15)
- Page 28 Tie a string between center slots on outer column in order to level the depth of each vertical column. 2018-05-15 #:146-9026-4 (2019-08-15)
- Page 29 Adjust depth, then remove string. Loosen, adjust, tighten. 2018-05-15 #:146-9026-4 (2019-08-15)
- Page 30 3/8" ENG Attach display, tighten connecting hardware, and run (10mm) cables one at a time starting from the bottom left. 2018-05-15 #:146-9026-4 (2019-08-15)
- Page 31 3/8" (10mm) 2018-05-15 #:146-9026-4 (2019-08-15)
- Page 32 3/8" ENG To remove, start from the top right. (10mm) 2018-05-15 #:146-9026-4 (2019-08-15)
- Page 33 This page intentionally left blank. 2018-05-15 #:146-9026-4 (2019-08-15)
- Page 34 This page intentionally left blank. 2018-05-15 #:146-9026-4 (2019-08-15)
-
Page 35: Limited Five-Year Warranty
(from date of the original installation of the product). At its option, Peerless-AV will repair or replace, or refund the purchase price of, any product which fails to conform with this warranty. - Page 36 Peerless-AV Peerless-AV Europe Peerless-AV de Mexico 2300 White Oak Circle Unit 3 Watford Interchange, Ave de las Industrias 413 Aurora, IL 60502 Colonial Way, Watford, Herts, Parque Industrial Escobedo Email: tech@peerlessmounts.com WD24 4WP, United Kingdom Escobedo N.L Mexico 66062 Ph: (800) 865-2112...