Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Hover-1 E-TRACK
Summary of Contents for Hover-1 E-TRACK
- Page 1 OP E RAT I ON M A N U A L H 1- T R A K...
- Page 2 HELMETS SAVE LIVES! Always wear a properly tted helmet that complies with CPSC or CE safety standards when you ride your Trak. Correct Fit: Make sure your helmet covers your forehead. Incorrect Fit: Forehead is exposed and vulnerable to serious injury.
- Page 3 • To avoid collisions, falls, and loss of control, please learn how to ride the E-Track safely. • You can learn how to ride the E-Track by reading the operation manual and watching videos. • All users are responsible for any consequences caused by violating warning contents or proper operations.
- Page 4 Use caution when riding the E-Track in cold temperatures (below 40°F/4°C). Doing so may increase the risk of mechanical failures of the dirt bike, which may lead to damage to your device, property damage, serious bodily injury, and even death.
- Page 5 • Do not operate or allow others to operate the E-Track, until the user understands all instructions, warnings and safety features described in this manual. • Check with your doctor if you have a medical condition that could affect your ability to use the E-Track.
-
Page 6: Specifications
INTRODUCTION The E-Track is a personal transporter. Our production processes are developed with strict testing for each E-Track dirt bike. Operating the E-Track without following the contents of this manual may lead to damage to your E-Track, or bodily injury. - Page 7 HOVER-1 E-TRACK DIAGRAM FEATURES/PARTS 1. Throttle 7. Motor 2. Handlebars 8. Foot Rest 3. Brake 9. Kickstand 4. Front Fender 10. Power switch (located on opposite side) 5. Tire 11. Charge Port (located on opposite side) 6. Seat...
-
Page 8: Parts List
PARTS LIST A. E-Track Dirt Bike Frame B. Handlebar Assembly C. Charger + Charging Cable D. Wrench + Hex Key/Screwdriver Tool E. Air Pump ASSEMBLING THE E-TRACK ASSEMBLE THE HANDLEBARS 1. Attach the 4 included washers to the large screws (A). Align the clamps (B & C) with the handlebar grooves. - Page 9 ASSEMBLE THE FRONT FENDER 1. Align the middle hole of the front fender (D) with the front fork and insert the small hex screw. Cap the end of the screw with the included lug nut. 2. Use the smaller hex key to tighten the screw and the wrench to tigthen the lug nut. ASSEMBLE THE NUMBER PLATE 1.
-
Page 10: Inflating The Tires
INFLATING THE TIRES Your E-Track dirt bike comes equipped with 12 inch air-filled tires. It is important you keep the tire pressure at the recommended psi levels (65 psi). Regularly check the tire pressure of your tires. If air is needed, attach the included air pump to the input valve on each tire and pump the tires until they reach 65 psi. -
Page 11: Before Riding
BEFORE RIDING It is important that you fully understand all the functions of your E-Track. If these functions are not used correctly, you will not have full control of your E-Track. Practice using the E-Track at slower speeds in a flat, open area before taking the device out into public areas. - Page 12 • Any and all axle guards, chain guards, or other covers or guards supplied by the manufacturer are in place and in serviceable condition. • The tires are in good condition, inflated properly, and have sufficient tread remaining. WARNING To reduce the risk of injury, adult supervision is required.
-
Page 13: Safety Precautions
Hover-1 is not liable for tickets or violations given to riders who do not follow local laws and regulations. • For your safety, always wear a helmet that meets CPSC or CE safety standards. - Page 14 • Use your best judgment to keep yourself out of dangerous situations with your E-Track. • Do not ride your E-Track off of curbs, ramps, or attempt to operate it in a skate park or empty pool. Misuse of your E-Track voids the manufacturer warranty and may lead to injury or damage.
- Page 15 • Do not ride your E-Track near motor vehicles or on public roads. • Do not travel up or down steep hills. • The E-Track is intended for use by a single individual. DO NOT attempt to operate the E-Track with two or more people.
- Page 16 Slow down and ride cautiously. Get off and move your E-Track to a safe operating space if needed. When you are ready to stop riding, bring your E-Track to a full stop and flip the power switch to off.
- Page 17 • Minimum Weight: 44 lbs OPERATING RANGE The E-Track can travel a distance up to 9 miles on a fully charged battery in ideal conditions. The following are some of the major factors that will affect the operating range of your device: •...
- Page 18 • After fully charging your dirt bike, unplug the charger from your device and from the wall outlet. A full charge may take up to 4 hours. Do not charge the E-Track longer than 4 hours, even if the light does not change to green.
-
Page 19: Battery Care / Maintenance
• When charging the dirt bike, only use the enclosed 1-pin charging cable provided by Hover-1. Use of any other charger or cable may lead to damage to the dirt bike, overheating, and risk of fire. Use of any other charger or cable voids the manufacturer warranty. - Page 20 • The battery contains dangerous substances. Do not open the battery or insert anything into the battery. • Only use the charger provided by Hover-1. • Do not attempt to charge the device if the battery has discharge or emits any substances. In that case, immediately distance yourself from the battery in case of fire or explosion.
-
Page 21: Care And Maintenance
• Do not dispose of the E-Track in fire as it may explode or combust. • Do not let the E-Track come into contact with sharp objects, as this will cause scratches and damage. -
Page 22: Warranty
WARRANTY For warranty information, please visit us at www.hover-1.com. Manufacturer: DGL Group, Ltd. 2045 Lincoln Highway, Edison, NJ 08817 TEL: 732-692-5000 Affix Serial Number Label Here:... - Page 23 @Hover1Rideables @RideHover1 @RideHover1 www.Hover-1.eu...