Related Manuals for Hover-1 PRO ALTAI R500
Summary of Contents for Hover-1 PRO ALTAI R500
- Page 1 Altai Owner's Manual DGL Group Assembly & Maintenance 2045 Lincoln Highway Edison, NJ 08817 All users must read and understand this handbook before irst use. support@hover-1.com | hover-1.com...
- Page 2 HOVER 1 PRO SERIES Thank you for choosing a Hover-1 Altai. It is our pleasure to guide you through Join our Hover 1 Community setting up your Altai and hitting the road! of riders wherever you are! Please read through this Owner’s Manual to get familiar with the proper operation of your Altai E-Bike’s controls, features, capabilities, and...
-
Page 3: Table Of Contents
19. SAFETY CHECKLIST 21. OPERATIONS First Ride Start Your E Bike Throttle Pedal Assist Control Cruise Control USB Operation Setting Menu Light System Suspension Fork Adjustment Braking Hover-1 E Mobility App Bluetooth Connectivity Display Screen Information Error Codes 35. MAINTENANCE 41. WARRANTY... -
Page 4: Basics
D I A G R A M O F T H E A L T A I Hydraulic Brakes Twist Throttle Racing Seat 3.5” Full LCD Display LED Taillight LED Headlight Rear Mudguard Spring Suspension Fork Hover-1 Pro Series Motor Removable Battery Crank Arm / Pedals... -
Page 5: General Symbols
Possible dangers to your life and health if respective calls to action are ignored. • Do not make any aftermarket modifications to your Altai that are not expressly approved by Hover-1 Pro Series. WARNING • Do not ride the E-Bike if you exceed the maximum weight limit of 264 lbs Warns about a situation that can cause death, serious physical injury and/or heavy material damage if safety instructions are ignored. -
Page 6: Assembly
Take pictures if you suspect rough handling and Set of pedals contact: support@hover-1.com Battery charger If you require additional assistance, please reach out to support@hover-1.com Battery for more information. We often update user guides based on the feedback we receive from our customers. -
Page 7: Unpacking Instructions
UNPACKING INSTRUCTIONS Please exercise caution when Take all parts and tools out of the lifting the box, as it weighs about box. Please refer to the 'Tools 73 lbs. Needed' section to ensure that you have all the necessary parts for assembly. -
Page 8: Install The Handlebars
DANGER DANGER INSTALL THE HANDLEBARS Properly inflate the tires between 26-30 PSI. Do not over-inflate the tires. Attach the handlebars to the E-Bike frame. Tilt the handlebars forward or back to adjust their position to your riding Remove all the wrapping preference. -
Page 9: Connect The Display Cables
WARNING Do not over tighten the stem bolt. Over tightening the stem bolt can damage the steering system and cause loss of control. CONNECT THE DISPLAY CABLES Match the colored cables to the same-colored ports behind the display: NOTICE • 3 green cables •... -
Page 10: Install The Battery Pack
INSTALL THE BATTERY PACK Push open the rear re lector bracket loop and slide it onto the E Bike frame, next to the rear tire. Align the re lector horizontally (parallel to the ground), with the re lective piece facing the rear of the E Bike. Match all the notched joints of the Clamp the rear re lector to the E Bike frame and completely tighten the battery to the E-Bike frame and slide... -
Page 11: Safety Checklist
5. Lighting Please be sure all the items you installed are properly torqued, tightened, and connected! If there any questions, please contact us: support@hover-1.com Check if the headlight and taillight are working properly. To be sure your E-Bike is safe on the road, please use the... -
Page 12: Operations
Cruise control is set to ‘off’ by default. You must enable cruise control through Press and hold the power button. the E-Bike’s setting menu (refer to pages 24-25) or through the Hover-1 Then, press the battery button to ‘o’. The E-Bike will shut off. -
Page 13: Usb Operation
If an error indicator appears on the display, please check the error code list. repeat for the remaining If you still require assistance, please contact customer support at: 1919 numbers until finished. support@hover-1.com P02: Wheel Diameter Setting Press ‘+’ or ‘-’ to switch the figure from 12C to 28C Twist Throttle... -
Page 14: Light System
P05: Cruise Control LIGHT SYSTEM Press ‘+’ or ‘-’ to turn cruise control on/off. Turn On/O the Halo Light Click the L-shaped button above the high/low beam combo switch to turn the headlight on. Click the button again to turn it off. P06: Pedal Assist Setting Press ’+’... -
Page 15: Braking
Altai E-Bike’s exciting features! Horn Button Horn Button Turning Signals Turning Signals BLUETOOTH CONNECTIVIT Y Pairing Your E Bike for the First Time Turn on your smartphone’s Bluetooth. Open the Hover-1 E-Mobility App, search for the E-Bike, and connect. - Page 16 Reset Instructions for Pairing a New Phone to Your E Bike Continue pressing the ‘M’ button to cycle to P07 (Read through all the steps before you begin) Once the unit is switched to P07, press the power Press the power button to turn button.
- Page 17 How to Unpair Your E Bike Each Altai E-Bike comes programmed in speed restriction mode, which allows Open the Hover-1 E-Mobility App. Press and hold the E-Bike you want for throttle operation and pedal assist up to 19.88 mph. This allows the Altai to remove.
-
Page 18: Display Screen Information
DISPLAY SCREEN INFORMATION ERROR CODES The main display presents several important metrics as follows: The electronics system has the ability to self-diagnose and report a limited set of errors. Errors will appear on the screen as error codes. Representation of how much charge Battery level graphic The chart below explains the meaning of each error code: remains in the battery. -
Page 19: Maintenance
MAINTENANCE Charge the Battery Pack It is recommended to do a maintenance check-up of your E-Bike at least once a It is recommended that the battery be charged for about 7-8 hours prior to your year. It is advised that the first maintenance check-up be performed after the first first use to help prime the lithium-ion battery cells for optimal performance. - Page 20 SEAT MAINTENANCE • Do not use any charger that has been dropped. Do not short-circuit the battery pack’s terminals. 1. If the seat is dusty or dirty, use a cloth with gentle soap and water for cleaning. • Do not overcharge the battery. 2.
- Page 21 CHAIN SPECIFICATIONS SPECIFICATIONS It is recommended that you inspect the chain tensioner for wear and tear. Model: H1 ALT50 Periodically lube the chain. If the chain is sagging or seems more loose Net Weight: 72 lbs than normal, you may need to tighten the chain. Max Supported Weight: 264 lbs It is recommended that you purchase chain lube for daily chain Max Speed: 20 mph Class-1 mode / 28 mph Unlimited mode...
-
Page 22: Warranty
The warranty will be considered void if: cost. The warranty will be ful illed on a case-by-case basis at Hover-1 Pro Series’ discretion. Products and/or parts that have been replaced or 1. - Page 23 If it is determined that a valid warranty claim exists. Hover-1 Pro Series may send replacement parts or issue an RMA number (Return Material Authorization) to return the damaged product as Hover-1 deems appropriate.