Related Manuals for Taurus B970
Summary of Contents for Taurus B970
- Page 1 Assembly and Operating Instructions max. 400 kg ~ 60 Min. 43 kg L 145 | B 66 | H 125 TFB970.01.01 Art. No. TF-B970 Taurus Weight Bench B970...
- Page 2 B970...
-
Page 3: Table Of Contents
Content GENERAL INFORMATION Technical Data Personal Safety Set-Up Place ASSEMBLY General Instructions Scope of Delivery Assembly STORAGE AND TRANSPORT General Instructions Transportation Wheels TROUBLESHOOTING, CARE AND MAINTENANCE General Instructions Faults and Fault Diagnosis Maintenance and Inspection Calendar DISPOSAL RECOMMENDED ACCESSORIES ORDERING SPARE PARTS Serial Number and Model Name Parts List... - Page 4 B970...
- Page 5 With Taurus® fitness equipment, the focus is on what sport is all about: maximum performance! Therefore, the equipment is developed in close consultation with athletes and sports scientists.
- Page 6 This notice indicates potentially hazardous situations which, if not avoided, will result in death or serious injuries! NOTICE This notice indicates further useful information. Retain these instructions in a safe place for future reference, maintenance or when ordering replacement parts. B970...
-
Page 7: General Information
GENERAL INFORMATION Technical Data Weight and Dimensions Article weight (gross, incl. packaging): 46 kg Article weight (net, excl. packaging): 43 kg Package dimensions (L x W x H): approx. 134 cm x 42 cm x 24.5 cm Set-up dimensions (L x W x H): approx. 145 cm x 66 cm x 125 cm Maximum load: 400 kg... -
Page 8: Personal Safety
Make sure that nobody is within the range of motion of the equipment during training so as not to endanger you or other persons. ࣑ ATTENTION Do not insert any objects of any kind into the openings of the device. B970... -
Page 9: Set-Up Place
Set-Up Place WARNING ⚠ Do not place the equipment in main corridors or escape routes. ⚠ CAUTION Choose a location in which to place the equipment such that there is enough free space/ clearance to the front, the rear and to the sides of the equipment. The training room should be well ventilated during training and not be exposed to any draughts. -
Page 10: Assembly
To prevent damage to the equipment and the floor, assemble the equipment on a mat or packaging board. NOTICE In order to make the assembly as simple as possible, some screws and nuts to be used can already be pre-assembled. Ideally, assemble the equipment at its later set-up place. B970... -
Page 11: Scope Of Delivery
Scope of Delivery The scope of delivery consist of the following parts. At the beginning, check whether all parts and tools belonging to the device are included in the scope of delivery and whether damage has occurred. In the event of complaints, the contractual partner must be contacted directly. CAUTION ⚠... -
Page 12: Assembly
Step 1: Assembly of the buttom tube Fasten the buttom tube (2) together with the fixed plate (3) to the main frame (1) with two bolts (15), four washers (18) and two nuts (17). Tighten the bolts and nuts. B970... - Page 13 Step 2: Assembly of the shark fin design plates Fasten the two shark fin design plates (4) to the two sides of the main frame (1) with three bolts (15), six washers (18) and three nuts (17). Tighten the bolts and nuts.
- Page 14 Assembly of the seat tube and back tube Fix the seat tube part (6) and the two parts of the back tube (5) to the main frame (1) with a bolt (19), two washers (23) and a nut (22). Tighten the bolt and nut. B970...
- Page 15 Step 4: Assembly of the leg press part 1 Connect the adjustment tube and the adjustment sleeve (7 & 8) with a bolt (25). Tighten the bolt.
- Page 16 Fix the adjustment tube (7) to the seat tube part (6) with a bolt (20), two washers (23) and a nut (22). Fix the adjustment sleeve (8) to the main frame (1) with a bolt (21), two washers (23) and a nut (22). Tighten the bolts and nuts. B970...
- Page 17 Step 6: Assembly of the support tube Secure the support tube (9) between the two back tubes (5) with a bolt (19), two washers (23) and a nut (22). Tighten the bolt and nut.
- Page 18 Step 7: Assembly of the leg press Part 3 Attach the handle part (10) to the seat tube part (6) with two bolts (20), four washers (23) and two nuts (22). Tighten the bolts and nuts. B970...
- Page 19 Step 8: Assembly of the leg press Part 4 Place one foam (11) on each side of the handle part (10) and secure it with one foam cap (12) and one screw (16). Tighten the screws.
- Page 20 Step 9: Assembly of the seat cushion Secure the seat cushion (13) to the seat tube part (6) with four bolts (25) and four washers (26). Tighten the bolts. B970...
- Page 21 Step 10: Assembly of the back cushion Secure the back cushion (14) to the two back tubes (5) with four bolts (24) and four washers (26). Tighten the bolts.
-
Page 22: Storage And Transport
The equipment must not be used until it has been repaired. If necessary, use only original spare parts. ࣑ ATTENTION In addition to the instructions and recommendations for maintenance and care given here, additional service and/or repair work may be necessary; this must only be carried out by authorised service technicians. B970... -
Page 23: Faults And Fault Diagnosis
Faults and Fault Diagnosis The equipment undergoes regular quality controls during production. Nevertheless, faults or malfunctions may occur. Frequently, individual parts are responsible for these disturbances, an exchange is usually sufficient. Please refer to the following overview for the most common errors and how to correct them. -
Page 24: Recommended Accessories
Of course, you can also contact our customer service: by telephone, e-mail, in one of our branches or via our social media channels. We will be happy to advise you! chest strap floor mat chest strap contact gel silicone spray towels B970... -
Page 25: Ordering Spare Parts
It's located on a white sticker. The exact position of this sticker is shown the following illustration. Enter the serial number in the appropriate field. Serial number: Brand / Category: Taurus / weight bench Model Name: Weight Bench B970 Article Number: TF-B970... -
Page 26: Parts List
Foam cap Seat cushion Back cushion Hexagon bolt M10*90 Button head socket screw M10*10 Lock nut Washer Φ10 Hexagon bolt M12*210 Hexagon bolt M12*150 Hexagon bolt M12*120 Lock nut Washer Φ12 Hexagon bolt M8*70 Hexagon bolt M8*30 Washer Φ8 B970... -
Page 27: Exploded Drawing
Exploded Drawing... -
Page 28: Warranty
WARRANTY Training equipment from Taurus® is subject to strict quality control. However, if a fitness equipment purchased from us does not work perfectly, we take it very seriously and ask you to contact our customer service as indicated. We are happy to help you by phone via our service hotline. - Page 29 Warranty Conditions For the warranty to be valid, the following steps must be taken: Please contact our customer service by email or phone. If the product under warranty has to be sent in for repair, the seller bears costs. After expiry of the warranty, the buyer bears the costs of transport and insurance.
-
Page 30: Contact
�� Mo - Fr 08:00 - 18:00 09:00 - 18:00 09:00 - 18:00 Please find a detailed overview including address and opening hours for all stores of the Sport-Tiedje Group in Germany and abroad on the following website: www.sport-tiedje.com/en/stores B970... - Page 31 LIVE FITNESS WEBSHOP AND SOCIAL MEDIA Sport-Tiedje is Europe’s largest specialist store www.sport-tiedje.co.uk for home fitness equipment with currently over www.sport-tiedje.de/blog 70 stores and one of the world’s most renowned online mail order companies for fitness equipment. Private customers order via the 25 www.facebook.com/SportTiedje web shops in the respective national language or have their desired equpiment assembled on...
- Page 32 Taurus Weight Bench B970...