Connecting The Hob; Disposal - Hotpoint Ariston CISKBT 6001 H IX/HA Operating Instructions Manual

Connecting the hob

• The electrical safety of this appliance can only be
guaranteed if the latter is correctly and efficiently earthed, in
compliance with regulations on electrical safety. Always
ensure that this vital safety measure has been taken. If you
have any doubts, call in a qualified technician to check the
electrical system thoroughly.
• The manufacturer denies all responsibility for damage
resulting from a system which has not been earthed
correctly.
• Before powering the appliance, check whether the
technical characteristics featured on the appliance data
plate correspond with those of the mains electrical system.
• Check that the current load of the mains supply and of the
power sockets is suitable for the maximum power of the
appliance, indicated on the appliance data plate. If in doubt,
contact a qualified professional.
Disconnect the appliance from the electricity supply Disconnect the appliance from the electricity supply Disconnect the appliance from the electricity supply Disconnect the appliance from the electricity supply Disconnect the appliance from the electricity supply
before all operations. before all operations. before all operations. before all operations. Connect your hob to the electrical before all operations.
system by means of a junction box: junction box: junction box: junction box: if the appliance is junction box:
connected permanently to the mains, an omnipolar circuit
breaker breaker breaker breaker, accessible if necessary, with a minimum contact breaker
opening of 3 mm should be installed.
Single-phase connection
The hob is equipped with a preconnected electricity supply
cable, which is designed for single-phase connection.
Connect the wires according to the instructions given in
the following table and diagrams:
Voltage and
Electrical cable
mains frequency
230V 1+N ~
50 Hz
Other types of connection
If the mains supply corresponds with one of the following:
Voltage and mains frequency
• 400V - 2+N ~ 50 Hz
• 230V 3 ~ 50 Hz
• 400V - 2+2N ~ 50 Hz
Separate the wires and connect them according to the
instructions given in the following table and diagrams:
Voltage and
Electrical cable
mains frequency
400V - 2+N ~
50 Hz
230V 3 ~
50Hz
400V - 2+2N ~
50 Hz
If the mains supply corresponds with one of the following:
Voltage and mains frequency
• 400V 3 - N ~ 50 Hz
proceed as follows:
! The cable provided is not suitable for the following types
of installation.
1. Use a suitable supply cable, H05RR-. or higher, with the
right dimensions (cable section: 2.5 mm).
2. To open the terminal board, insert a screwdriver into the
side tabs of the cover and open it (see Terminal board
picture).
3. Loosen the cable clamp screw and the terminal board
screws according to the type of connection required and
position the connection supports as shown in the following
table and diagrams.
4. Position the wires according to the following table and
diagrams and connect the appliance by tightening all the
screws for the springs as much as possible.
5. Secure the power supply cable by fastening the cable
clamp screw, then put the cover back on.
omnipolar circuit omnipolar circuit omnipolar circuit omnipolar circuit
Phase
Wire connection
: yellow/green;
N: the two blue wires
together
L: brown and black
- 73/23/EEC dated 19/02/73 (Low Voltage) and subsequent
together
amendments;
- 89/336/EEC dated 03/05/89 (Electromagnetic
Compatibility) and subsequent amendments;
- 93/68/EEC dated 22/07/93 and subsequent amendments.

Disposal

Wire connection
• When disposing of packaging material: observe local
: yellow/green;
N: the two blue wires together
• The European Directive 2002/96/EC relating to Waste
L1: black
L2: brown
: yellow/green;
N1: blue
N2: blue
L1: black
L2: brown
Voltage and
Electrical connections
mains frequency
400V 3-N ~ ı 50
Hz
Phase Phase Neutral Earth
U-bolt
connection support
This appliance conforms to the following
European Economic Community directives:
legislation so that the packaging may be reused.
Electrical and Electronic Equipment (WEEE) states that
household appliances should not be disposed of using
the normal solid urban waste cycle. Exhausted
appliances should be collected separately in order to
optimise the cost of re-using and recycling the materials
inside the machine, while preventing potential damage to
the atmosphere and to public health. The crossed-out
dustbin is marked on all products to remind the owner of
their obligations regarding separated waste collection.
.or further information relating to the correct disposal of
exhausted household appliances, owners may contact
the public service provided or their local dealer.
Terminal board
Three-phase 400
Three-phase 400
3
GB