4.8. After usage .................... 13 4.9. Warning tones of the InnoMake Clip ............ 14 4.10. Overview of the InnoMake Clip signals ..........14 5. Safety instructions................ 16 5.1. Notes and measures in case of (mal)function of the product ....17 5.2.
For unrestricted and safe use of the InnoMake Clip, it is important to read these instructions for use carefully, including the safety instructions. With these Instructions for Use, we would like to help you get to know the InnoMake Clip product and facilitate your first steps with the product.
Next to the symbol of a painted factory building, the legal manufacturer of the InnoMake clip is noted along with the postal address. Declaration of Conformity according to the applicable European...
We refer to the side facing away from the body as the front. The opposite surface of the InnoMake clip is the back. The front side faces in the direction of walking during use and can also be recognized by the fact that our company logo, a dot with three waves, is raised in the area below the two openings.
4.2. On the back of the InnoMake Clip there is a pushbutton in the upper left corner which can be used to switch the device on and off and to control other functions. The pushbutton as a control element is described in more details in section 2.2.
InnoMake app is opened for the first time. If additional control of the InnoMake Clip by the app is not desired, using the device is based on the standard settings of the InnoMake Clip at delivery.
However, the use of the InnoMake Clip without a primary aid and/or without existing residual vision is only permitted in a familiar environment (e.g., home environment, suitable workplace) if the user feels safe enough even if the InnoMake Clip fails to continue on my way unharmed.
InnoMake Clip. Users of the InnoMake Clip do not require any formal education in the relevant field of health care or a medical specialty. The InnoMake Clip may not be passed on to other persons.
4.1. Power on/off and ready state Power on The device is switched on by pressing the button on the back of the InnoMake Clip for at least 2 seconds. An ascending audio signal indicates switching on. There is also a continuous vibration during the sound signal.
USB plug on one side, which is the international USB mark. This tactile sign must point against the viewing direction of the InnoMake Clip when plugging it into the micro-USB socket. Then connect the charger's power pack to a voltage source (220- 230V).
Before using it for the first time, you should first familiarize yourself with the functions of InnoMake Clip in your usual environment, for example by standing in front of a wall and slowly moving towards or away from it, which increases or decreases the vibratory feedback.
1 long tone followed by 1 short tone in the same pitch means the LED is deactivated. 4.8. After usage When you have finished using the InnoMake Clip, you should switch off the device. The following questions will help to prepare the InnoMake Clip for the next usage: •...
This is followed by a descending sound signal as when the InnoMake Clip is switched off. We recommend charging the InnoMake Clip after each use to prepare it for the next use. Charging the battery is described in section 4.2.
Page 15
Vibratory Occurrence Keystroke Acoustic signal LED-Signal signal section Power on 1x long 3x ascending tones 1x long impulse 1x weakening Power off 1x long 3x descending tones impulse Following "Switch on" and corresponds Operational state to the signal tone of the last set measuring range 1,0 meter...
Failure to observe alarms can lead to bodily injury or even damage to property, especially if the device overheats, if obstacles are ignored The InnoMake Clip must not be dried with hot air, e.g., a hair dryer, but only in the air at room temperature.
Abrupt changes in the environment may result in functional limitations or unreliable feedback. 5.1. Notes and measures in case of (mal)function of the product Tipps, how to react to (mal-)functions of the InnoMake Clip. Malfunctions Possible reasons Necessary actions Cleaning the InnoMake Clip see Dirt on the sensors section 6.2...
Page 18
Connect charger to power Ready-to-operate Restart the device, if necessary state is not Software error charge the battery first established NOTE If the InnoMake Clip behaves in an incomprehensible manner or there are persistent, unexpected malfunctions, the dealer must be contacted. TDIMC1_4_User Manual_IMC-1.1.0_EN...
USB port facing down. This will allow any water that may have accumulated to leak out of the waterproof USB port. If the InnoMake Clip cannot be switched on after coming into contact with water or other liquids, or if it emits a continuous vibration after being switched on, the application must be terminated, and the dealer is to be contacted.
NOTE It is essential to keep the InnoMake Clip and the USB charging cable out of the reach of small children < 3 years of age. Due to the length of the USB cable of 1 meter, there is a risk of strangulation! For returning the InnoMake Clip to the dealer or to us, the most suitable product packaging for the return is the one in which the product was delivered.
Gross soiling, such as dried soil, can be removed with a damp cloth. A lint-free cloth is suitable for less stubborn soiling and for drying the device. Allow the InnoMake Clip to air dry completely after drying. Brushes or other cleaning utensils that could damage the surface of the InnoMake Clip should not be used for cleaning.
Page 22
Battery charging time approx. 2,5 hours Behaviour of the InnoMake clip during The function of the InnoMake Clip is reduced loading process to the output of the battery charge level Operating time of the InnoMake Clip with new, fully charged battery, at room approx.
Legal notice CE-conformity With the CE marking on the InnoMake clip, we assure that we meet the requirements of the • EU 2017/745 Regulation of the European Parliament and of the Council of 5 April 2017 concerning medical devices • 2014/53/EU RED- Directive •...
Page 24
Tec-Innovation GmbH Headquarter: 2123 Hautzendorf, In der Au 5 Office: Holz-Steiner Straße 6/6/1 A-2201 Gerasdorf bei Wien Contact: +43 1 226 44 66 office@tec-innovation.com www.tec-innovation.com TDIMC1_4_User Manual_IMC-1.1.0_EN...