Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Logic Controls LD9000
Summary of Contents for Logic Controls LD9000
-
Page 1: User Manual
Models: LD9000 Series Customer Displays 2 by 20 character display USER MANUAL... -
Page 2: Fcc Notice
The manufacturer of the POS pole display makes no representations or warranties, either expressed or implied, by or with respect to anything in this manual, and shall not be liable for any implied warranties of fitness for a particular purpose or for any indirect, special or consequential damages. -
Page 3: Table Of Contents
TABLE OF CONTENTS FEATURES ...1 MODEL IDENTIFICATION...2 CARTON CONTENTS ...2 INSTALLATION ...3 FUNCTIONAL TEST...5 INTERFACE CONNECTION...8 SOFTWARE COMMANDS ... 10 HARDWARE CONFIGURATION ... 11 DISPLAY CHARACTER CODES ... 12 GENERAL SPECIFICATIONS ... 13... -
Page 4: Features
FEATURES The LD9000 family of pole displays offers a wide range of high quality features and models to choice from. Listed below are the features incorporated into each pole display. Not all features are available in all models. The model identification chart will assist you in selecting the model best suited to your needs. -
Page 5: Model Identification
MODEL IDENTIFICATION LD9 __ __ __ - __ __ COMMAND SET 0 = LOGIC CONTROLS* 1 = LOGIC CONTROLS WITH PASS-THRU 2 = SPECIAL COMMAND SET 1 (Aedex emulation) 3 = SEPCIAL COMMAND SET 2 (Noritaki emulation) 4 = SPECIAL COMMAND SET 3 (Epson D202 emulation) -
Page 6: Installation
INSTALLATION Your LD9000 family of pole displays has been pre-assembled to make the installation as simple as possible. Serial Interface Non-pass-thru Models Installation 1. Mount the pole display to the metal base plate using the mounting hardware provided. 2. The pole display can be used in a freestanding mode or attached to the counter using the remaining mounting hardware. - Page 7 Serial Interface Pass-thru Models Installation 1 Mount the pole display to the metal base plate using the mounting hardware provided. 2 The pole display can be used in a freestanding mode or attached to the counter using the remaining mounting hardware.
-
Page 8: Functional Test
Type “MODE COM1 96,N,8,1” and press the ENTER key. Type “TYPE CON>COM1” and press the ENTER key. LD9000, LD9300, LD9400, LD9500 and LD9900 1. Type “ABCDEFGH” and press ENTER key. The display will show “ABCDEFGH” on the first line. - Page 9 LD9100-PT, LD9300-PT, LD9400-PT and LD9900-PT 1. Type “ABCDEFGH” and press ENTER key. The display will show “ABCDEFGH” on the first line. 2. Type “^APASSTHRU” (^A is entered as Ctrl-A ) and press ENTER key. The data will be passed through to the peripheral (e.g. a printer).
- Page 10 LD9190-PT, LD9390-PT, LD9490-PT and LD9990-PT 1. Type “ECHO ABCDEFGH>LPT1” and press ENTER key. The display will show “ABCDEFGH” on the first line. 2. Type “ECHO ^APASSTHRU>LPT1” (^A is entered as Ctrl-A) and press ENTER key. The data will be passed through to the peripheral (e.g.
-
Page 11: Interface Connection
INTERFACE CONNECTION Serial Interface Connector Configuration The pin out configuration for the standard serial pole display is a DB9F connector. It plugs directly into the serial port of the computer. 1. DCD (tied to pins 4&6) 2. NC 3. TXD from PC 4. - Page 12 Parallel Interface Connector Configuration All standard parallel pole displays will have a DB25 male connector. It is connected to the printer port of the computer. –Strobe Data 0 Data 1 Data 2 Data 3 Data 4 Data 5 Data 6 Data 7 –Ack Busy...
-
Page 13: Software Commands
SOFTWARE COMMANDS Logic Controls pole displays are controlled by command codes and data from the computer. The model of pole display that you have will determine which command set works with your pole. Refer to the model identification chart for further information. -
Page 14: Hardware Configuration
HARDWARE CONFIGURATION Serial pole displays were factory configured for serial RS232C interface using the following protocol: · 9600 Baud Rate · 8 Data Bits · 1 Stop Bit · No Parity Other optional baud rates are available with factory settings. Refer to the model identification chart for further information. -
Page 15: Display Character Codes
DISPLAY CHARACTER CODES " & ’ < > ‘... -
Page 16: General Specifications
Vibration (10 to 55 Hz.) Shock CABLES & CONNECTORS: Serial Display cable Interface cable Power adapter Parallel Display cable LD9000 LD9000X 2 x 2 sides 5 x 7 5 x 7 0.374in. (9.5mm) 0.374in. (9.5mm) 0.244in. (6.2mm) 0.244in. (6.2mm) ASCII...