Advertisement
Quick Links
22x24x12 Peak Style Run-in Shed
Please read instructions completely before assembly
Description
Cross Rail Plain Ends
Extension
Straight Leg Tube
Cross Rail Swedged
Cross Rail Swedged
Cross Rail Plain End
Cross Rail Plain End
Corner Upright Leg
Side Bend Tube
End Top Bend
Middle Top Bend
Wind Brace
Wind Brace
All-Weather Cover
Protective Boot
4-Way Cover Rail Clamp
3-Way Cover Rail Clamp
Bolt Cap
5/16"x 4" Round Head Bolt
5/16"x 4" Bolt
5/16"x 4 1/2" Bolt
5/16"x 2 3/4" Bolt
5/16"x 2 1/4" Bolt
5/16"x 2" Bolt
5/16" Nuts
Ratchet
Temporary 30"Auger Anchors
Cable - 1' Lengths
Cable Clamps
Base Feet
Description
45"L
59.4"L
38"L
50 1/2"L
48 1/2"L
46.6"L
48.5"L
30"L
54.2"L
Part #
Qty.
Part #
Qty.
11105
10
11068
24
11019
8
11102
11
11103
1
1
11101
2
11104
11016
4
11013
12
11136
2
11135
4
4
11095
11093
4
1A7254
1
800196
4
11107
16
11106
8
11150
24
11133
4
11132
8
11134
4
11131
60
11130
20
648
6
690
102
10040
4
822
6
11270
8
58542
Model #
BASIC HAND TOOLS
REQUIRED FOR ASSEMBLY:
• Adjustable Wrench
• Rubber Mallet
ATTENTION:
BOLTS ARE NOT
NEEDED OR
INCLUDED FOR EVERY
CONNECTION BUT
MAY BE
PURCHASED BY CALLING
THE NUMBER BELOW.
FOR MISSING OR
REPLACEMENT PARTS
OR QUESTIONS
PLEASE CONTACT
CUSTOMER SERVICE:
1.800.524.9970
150 Callendar Road
Watertown, CT 06795
PAGE 1
05-58542-0B 08/06/08
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for ShelterLogic 58542
Summary of Contents for ShelterLogic 58542
- Page 1 11134 5/16"x 2 3/4" Bolt 11131 5/16"x 2 1/4" Bolt 11130 5/16"x 2" Bolt 5/16" Nuts Ratchet 10040 150 Callendar Road Watertown, CT 06795 Temporary 30”Auger Anchors Cable - 1’ Lengths Cable Clamps PAGE 1 Base Feet 11270 05-58542-0B 08/06/08...
- Page 2 Basic Frame Assembly STEP 1 Fit together an end rib using the following parts, (1) #11136 3-Way Top Connector, (4) #11068 Swedged Rafter Pole, (2) #11013 Side Bend Tube and (2) #11016 Bend Corner Leg. Using (8) 11131 5/16 X 2 3/4" bolts and (8) 690 5/16" nuts securely fasten the joints of all parts.
- Page 3 STEP 4 With help stand the first end rib vertically and lean against a permanent structure such as a tree or a fence. Attach the plain end of a #11102 horizontal tube and a wind brace assembly to the first rib using a #11134 5/16 X 4 1/2" bolt and a #690 5/16"...
- Page 4 STEP 7 Install the other end rib as you had installed all the middle ribs only use #11104 crossrails and attach the sliding crossrail using the remaining 3-way coverrail clamps. Note: The final windbrace assemblies should be installed as shown. Be sure the upper of the windbraces are installed between the rib and crossrail Step 8 Installing T op Rail...
- Page 5 STEP 11 INSTALLING AUGER ANCHORS Using a 3/4" pipe or steel rod, (a car tire iron works also) placed through the eyelet on the auger, screw it into the ground. Start at the four corners of the unit and space the remainder out evenly. Be sure to screw the anchor in fully (the eyelet should be a level where it can be securely attached to the frame.
- Page 6 STEP 8 Find the open side of the protective boot and open it. Insert the foot of the corner leg into the protective boot. When the foot is all the way in the boot insert the top edge of the boot into the hem of the cover (Fig 13). When complete secure the Velcro on the open side of the boot to close the boot.
-
Page 7: Customer Service
150 Callender Road Watertown, CT 06795 For Replacement Parts or Help with assembly, Please call: Customer Service: 1-800-524-9970 8am-7pm Mon-Sat EST...
Need help?
Do you have a question about the 58542 and is the answer not in the manual?
Questions and answers